XCXiulan Cheng

Xiulan Cheng

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xiulan Cheng has a total of 46 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Highly efficient metamaterial solar energy absorber from UV to NIR regime

    by Cuiwei Xue, Rujun Liao, Xueling Quan, Huanan Duan, Xiu-Lan Cheng

    We theoretically propose and experimentally demonstrate an ultra-broadband metamaterial absorber (MA) based on a quadrilayer structure, comprising a Cr-SiO 2 -Ge cube array atop a Ge-Cr base film. The geometric parameters were optimized using a hybrid particle swarm optimization (PSO) and gradient descent algorithm. The resulting absorber exhibits a simulated average absorption of 95.1%, which is matched by a measured average absorption of 84.1% across the ultraviolet to near-infrared spectrum (200–2000 nm). The simulated absorber exhibits a 90% absorption bandwidth of 1413 nm (587–2000 nm), along with polarization insensitivity and excellent angular stability under both TE and TM modes. Furthermore, quantitative analysis reveals a high solar-weighted absorption of 91.8%. Finally, the efficient generation of photoelectrons and hot carriers—facilitated by the Ge and Cr layers, respectively—highlights the device’s potential for applications in solar energy harvesting, photodetection, and photothermal conversion.


  • Inverse design and fabrication of high-efficiency perfectly vertical LNOI grating couplers

    by Cuiwei Xue, Rujun Liao, Xiaoman Li, Weiping Wu, Xin Jin, Xueling Quan, Minni Qu, Liying Wu, Liping Xu, Liucheng Fu, et al.

    A perfectly vertical grating coupler (GC) on X-cut lithium niobate on insulator (LNOI) platform is designed and demonstrated. The optimized random grating structure of GC is designed by an inverse design method and exhibits a simulated coupling efficiency of approximately −2.52 dB and measured coupling efficiency of approximately −3.18 dB at a communication wavelength of 1550 nm. This is the highest, to the best of our knowledge, measured result yet reported compared to the coupling efficiency of LNOI grating couplers without reflector in existing literature, regardless of the angle of incidence and the thickness of lithium niobate. The fabrication tolerance is investigated, and the discrepancy between simulation and experiment is analyzed.


  • High-efficiency thin-film lithium niobate apodized grating coupler utilizing negative diffraction angle

    by Rujun Liao, Xiaofeng Wang, Cuiwei Xue, Xueling Quan, Liping Xu, Liucheng Fu, Min Liu, Minni Qu, Yunliang Shen, Liying Wu, et al.

    Lithium niobate on insulators (LNOI), which is an integrated optoelectronic material platform with essential prospects, has an excellent electro-optical coefficient and a low loss window covering from visible to mid-infrared. However, both the lower refractive index of lithium niobate (LN) and the immaturity of processing techniques cause difficulties in achieving high coupling efficiency in grating couplers. Therefore, an apodized LNOI grating coupler utilizing a negative diffraction angle is proposed. The simulated and experimental coupling efficiencies are -2.1 dB and -2.8 dB at 1550 nm wavelength, respectively, which is the highest efficiency reported for LNOI grating couplers that do not incorporate additional materials or complex fabrication processes. The grating coupler also has high process and test tolerances, making it possible to realize it on different process platforms.


  • Graded-Index Lens Based Edge Coupler With Low-Loss, Broad Bandwidth for Efficient Coupling Between Silicon Waveguide and Standard Single-Mode Fiber

    by Jinbin Xu, Chenxing Guo, Yaqian Li, Xin Jin, Xueling Quan, Xiulan Cheng

    Efficient fiber-to-chip coupling is crucial for achieving high-performance silicon photonic chips. While lensed fiber to chip coupling has been extensively researched and proven excellent, it does have limitations such as strict alignment tolerance and high cost. Therefore, the recommended approach is the standard single-mode fiber (SMF)-to-chip coupling. One potential solution for SMF-to-chip coupling involves an edge coupler based on a graded-index (GRIN) lens; however, this method often requires a GRIN lens with numerous layers, making fabrication extremely challenging. In this study, we propose and experimentally validate an edge coupler based on a GRIN lens assisted by a complementary taper structure. This new type of composite structure demonstrates low coupling loss, broad bandwidth, and polarization insensitivity, enabling efficient SMF-to-chip coupling. Our design simplifies the fabrication process by significantly reducing the number of layers in the GRIN lens while achieving lower coupling losses compared to conventional GRIN lens-based edge couplers. Experimental results demonstrate that at 1550 nm, the measured TE and TM mode coupling losses are 1.21 dB and 1.78 dB respectively, while maintaining the 1 dB bandwidth exceeding 90 nm.


  • Open Access

    Study of the fabrication technology on tapered structure in quartz

    by Wu Liying, Liu Dan, Cheng Xiulan, Quan Xueling, Zhang Wenhao, Ma Ling

    Zero-mode waveguides (ZMWs) are nanostructures that drastically reduce the effective optical observation volume beyond the diffraction limit, thereby permitting the use of higher concentrations of fluorescently tagged molecules for single-molecule studies. This work presents the fabrication technology of quartz plasma etching to create tapered sidewalls for the application in ZMWs, utilizing an inductively coupled plasma (ICP) reactive ion etching tool. This method involves a meticulously designed two-step etching process to achieve quartz cavities with a minimum sidewall angle of approximately 60 deg. Initially, the process involves altering the photoresist pattern from a vertical to a tapered form, facilitated by the use of CF4/O2/Ar plasma at elevated radio frequency power settings. Subsequently, the quartz material is etched utilizing CF4 based plasma, with the tapered photoresist serving as a mask. This innovative approach allows for the successful transference of the tapered photoresist structure onto the quartz material, culminating in the formation of uniform and symmetrical tapered quartz cavities. Most importantly, the surface roughness (Rq) of the tapered quartz, measured to be around 3 nm, is extremely low and meets the stringent requirements for optical devices.


  • O-band and C-band dual-polarization SMF-28 edge coupler with SiON taper cladding based on silicon nitride platform

    by Yaqian Li, Jinbin Xu, Xueling Quan, Chenxing Guo, Xin Jin, Xiu-Lan Cheng

    Optical communication is progressing towards low power consumption and lightweight solutions, necessitating the integration of multispectral output capabilities within a single optical module. We demonstrate a SiN photonic platform-based edge coupler for a standard single mode fiber (SMF) that enables operation in both the O-band and C-band simultaneously. The device is composed of a multi-segment SiN inverse taper and SiON taper cladding with specific refractive index. The measured edge coupler exhibits a coupling loss of less than 1 dB/facet, 0.5 dB bandwidth exceeding 100 nm from 1260 nm to 1360 nm; and a coupling loss of less than 2 dB/facet, 1 dB bandwidth exceeding 100 nm from 1500 nm to 1600 nm. Furthermore, the polarization dependent loss (PDL) remained less than 0.3 dB throughout the measurement range.


  • Design and demonstration of high efficiency perfectly vertical grating couplers with a random structure

    by Xin Jin, Jinbin Xu, Cuiwei Xue, Chenxing Guo, Liucheng Fu, Min Liu, Yunliang Shen, Xueling Quan, Xiu-Lan Cheng

    Utilizing an automated optimization method, we propose a perfectly vertical grating coupler (PVGC) characterized by random structure, superior performance, simplified fabrication process, and increased minimum feature size (MFS). Within the range of MFS from 60 to 180 nm, the optimized PVGC exhibited a simulated coupling efficiency of approximately −2.0 dB at 1550 nm with a 34 nm 1-dB bandwidth. Experimental results for the PVGCs fabricated by electron beam lithography (EBL) demonstrated coupling efficiencies ranging from −2.5 to −2.8 dB with a 32 nm 1-dB bandwidth while maintaining high manufacturing tolerances. This represents the most outstanding experimental outcome to date regarding the coupling performance of a PVGC fabricated on a 220 nm silicon on insulator (SOI), without requiring any complex processes as reported in the existing literature.


  • Open Access

    Fabrication-constrained inverse design and demonstration of high-performance grating couplers

    by Xin Jin, Jinbin Xu, Yaqian Li, Cuiwei Xue, Rujun Liao, Liucheng Fu, Min Liu, Yunliang Shen, Xueling Quan, Xiulan Cheng

    A high-performance grating coupler (GC) operating at a wavelength of 1550 nm is proposed by utilizing the adjoint-based inverse design algorithm on a 220 nm silicon-on-insulator (SOI) substrate. The grating scheme offers several advantages, including simple structure, large minimum feature size (MFS), manufacturing friendliness, support for large-scale production and multi-project wafer (MPW) runs, etc., while simultaneously maintaining exceptional coupling performance and fabrication tolerance. The design process incorporates various fabrication constraints to satisfy the specifications of different foundry processes. The optimized GC demonstrates excellent coupling performance and 3 dB bandwidth within the MFS range of 60 to 180 nm. The simulated coupling efficiency (CE) of the GC with 130 nm MFS is -1.69 dB, whereas the experimentally measured CE of the fabricated GC using electron beam lithography (EBL) is -2.83 dB. Notably, the experimental CE of the GC with 180 nm MFS fabricated using 248 nm deep ultraviolet (DUV) lithography is -2.77 dB, representing the highest experimental CE ever reported for a single-layer etching C-Band GC supported by MPW runs fabricated on 220 nm SOI without utilizing any back reflector, multi-etch layer, or overlay. The manufacturing outcomes of the same GC structure employing different manufacturing processes are discussed and analyzed, providing valuable insights for the fabrication of silicon photonics devices.


  • Waveguide integrated trapezoidal germanium photodetector based on lateral PIN junction in SOI

    by Shen Lu, Liying Wu, Sipan Yang, Jinbin Xu, Yanqian Li, Xueling Quan, Xiulan Cheng

    Photodetector (PD) is considered as a key component in the applications of optical communications. With the technology development of germanium (Ge) epitaxy on silicon, the research on waveguide integrated germanium photodetector is becoming more popular for its good photo-response characteristics in the infrared wavelength band. However, to the best of our knowledge, the influence of Ge layer shape on the performance of photodetectors has not been paid attention yet. In this paper, the influence of different shapes of germanium layer on the performance of photodetectors was explored by using the simulation software of Lumerical FDTD and DEVICE. Moreover, responsivity and 3-dB bandwidth on mature silicon-on-insulator (SOI) platform were further studied, respectively. The morphology of epitaxial Ge layer in the lateral PIN-type waveguide integrated photodetector was fully optimized, and the photodetectors theoretically exhibit excellent output performance at the wavelength of 1550nm with a bias voltage of -1 V. Furthermore, the responsivity and 3-dB bandwidth of the trapezoidal Ge photodetectors are obviously higher than that of traditional rectangular germanium photodetectors with lower dark current. In detail, the responsivity in our proposed photodetector structure is 1.04 A/W, the 3-dB bandwidth is as high as 30.8 GHz, and the dark current is as low as 97 nA.

  • Design and fabrication of a high-performance binary blazed grating coupler for perfectly perpendicular coupling

    by Jinbin Xu, Sipan Yang, Liying Wu, Liping Xu, Yaqian Li, Rujun Liao, Minni Qu, Xueling Quan, Xiu-Lan Cheng

    A high-performance binary blazed grating coupler (BBGC) on a silicon-on-insulator (SOI) platform for perfectly vertical coupling has been proposed. The period and the etching depth of the grating and the fill factors of the sub-gratings are simulated optimally with manufacturable feature sizes, and the coupling efficiency (CE) is as high as −1.78 dB at 1550 nm with a broad 3-dB bandwidth of around 100 nm. Then, a BBGC with the CE of −3.69 dB at 1550.5 nm and a 3-dB bandwidth of about 70 nm was experimentally demonstrated. Moreover, a large process tolerance of about 20 nm on the narrower sub-grating width was proved, achieving the insertion loss lower than −4.64 dB at 1550 nm. The realization of the BBGC on a SOI platform is simple, repeatable, and compatible with standard complementary metal-oxide semiconductor (CMOS) technology.