APArina R. Potylitsyna

Arina R. Potylitsyna

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Arina R. Potylitsyna has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Adsorption of 2,4-Dichlorobenzoic Acid on Carbon Nanofibers Produced by Catalytic Pyrolysis of Trichloroethylene and Acetonitrile

    by Anna M. Ozerova, Elena S. Tayban, Inna L. Lipatnikova, Arina R. Potylitsyna, Yury I. Bauman, Igor P. Prosvirin, Yury V. Shubin, Aleksey A. Vedyagin, Ilya V. Mishakov, Olga V. Netskina

    In this study, carbon nanofibers were synthesized by the catalytic pyrolysis of trichloroethylene (CNF-Cl) and its mixture with acetonitrile (CNF-Cl-N). The addition of acetonitrile resulted in the incorporation of nitrogen in the CNF (0.33 at%), the removal of chlorine, an increase in oxygen-containing functional groups on the surface (from 1.6 to 3.6 at%), and an increase in the volume of mesopores (from 0.35 to 0.41 cm3·g−1) and macropores (from 0.115 to 0.393 cm3·g−1). The study of 2,4-DCBA adsorption on both CNFs revealed that the adsorption capacity showed dependence with a maximum on the 2,4-DCBA concentration in the solution, which was attributed to the electrostatic interactions of adsorbate with adsorbent at various pHs. The adsorption forces were effective over distances greater than the size of the 2,4-DCBA molecule, indicating volume pore filling. The maximum adsorption capacity occurred at 0.7–1.2 mM and a pH of 3.4 ± 0.1. CNF-Cl-N exhibited lower 2,4-DCBA adsorption than CNF-Cl-N due to its lower specific surface area, lower micropore volume, and higher concentration of oxygen-containing groups on the surface. However, these differences were not significant, suggesting that CNFs produced from both chlorine-containing wastes and their mixtures with nitrogen-containing compounds can be effectively used for water treatment to remove 2,4-DCBA.


  • Open Access

    Efficient Production of Segmented Carbon Nanofibers via Catalytic Decomposition of Trichloroethylene over Ni-W Catalyst

    by Arina R. Potylitsyna, Yuliya V. Rudneva, Yury I. Bauman, Pavel E. Plyusnin, Vladimir O. Stoyanovskii, Evgeny Y. Gerasimov, Aleksey A. Vedyagin, Yury V. Shubin, Ilya V. Mishakov

    The catalytic utilization of chlorine-organic wastes remains of extreme importance from an ecological point of view. Depending on the molecular structure of the chlorine-substituted hydrocarbon (presence of unsaturated bonds, intermolecular chlorine-to-hydrogen ratio), the features of its catalytic decomposition can be significantly different. Often, 1,2-dichloroethane is used as a model substrate. In the present work, the catalytic decomposition of trichloroethylene (C2HCl3) over microdispersed 100Ni and 96Ni-4W with the formation of carbon nanofibers (CNF) was studied. Catalysts were obtained by a co-precipitation of complex salts followed by reductive thermolysis. The disintegration of the initial bulk alloy driven by its interaction with the reaction mixture C2HCl3/H2/Ar entails the formation of submicron active particles. It has been established that the optimal activity of the pristine Ni catalyst and the 96Ni-4W alloy is provided in temperature ranges of 500–650 °C and 475–725 °C, respectively. The maximum yield of CNF for 2 h of reaction was 63 g/gcat for 100Ni and 112 g/gcat for 96Ni-4W catalyst. Longevity tests showed that nickel undergoes fast deactivation (after 3 h), whereas the 96Ni-4W catalyst remains active for 7 h of interaction. The effects of the catalyst’s composition and the reaction temperature upon the structural and morphological characteristics of synthesized carbon nanofibers were investigated by X-ray diffraction analysis, Raman spectroscopy, and electron microscopies. The initial stages of the carbon erosion process were precisely examined by transmission electron microscopy coupled with elemental mapping. The segmented structure of CNF was found to be prevailing in a range of 500–650 °C. The textural parameters of carbon product (SBET and Vpore) were shown to reach maximum values (374 m2/g and 0.71 cm3/g, respectively) at the reaction temperature of 550 °C.


  • Open Access

    Comparative Study on Carbon Erosion of Nickel Alloys in the Presence of Organic Compounds under Various Reaction Conditions

    by Alexander M. Volodin, Roman M. Kenzhin, Yury I. Bauman, Sofya D. Afonnikova, Arina R. Potylitsyna, Yury V. Shubin, Ilya V. Mishakov, Aleksey A. Vedyagin

    The processes of carbon erosion of nickel alloys during the catalytic pyrolysis of organic compounds with the formation of carbon nanofibers in a flow-through reactor as well as under reaction conditions in a close volume (Reactions under Autogenic Pressure at Elevated Temperature, RAPET) were studied. The efficiency of the ferromagnetic resonance method to monitor the appearance of catalytically active nickel particles in these processes has been shown. As found, the interaction of bulk Ni-Cr alloy with the reaction medium containing halogenated hydrocarbons (1,2-dichloroethane, 1-iodobutane, 1-bromobutane) results in the appearance of ferromagnetic particles of similar dimensions (~200–300 nm). In the cases of hexachlorobenzene and hexafluorobenzene, the presence of a hydrogen source (hexamethylbenzene) in the reaction mixture was shown to be highly required. The microdispersed samples of Ni-Cu and Ni-Mo alloys were prepared by mechanochemical alloying of powders and by reductive thermolysis of salts-precursors, accordingly. Their interaction with polymers (polyethylene and polyvinyl chloride) under RAPET conditions and with ethylene and 1,2-dichloroethane in a flow-through reactor are comparatively studied as well. According to microscopic data, the morphology of the formed carbon nanofibers is affected by the alloy composition and by the nature of the used organic substrate.


  • Open Access

    Synthesis of Chlorine- and Nitrogen-Containing Carbon Nanofibers for Water Purification from Chloroaromatic Compounds

    by Anna M. Ozerova, Arina R. Potylitsyna, Yury I. Bauman, Elena S. Tayban, Inna L. Lipatnikova, Anna V. Nartova, Aleksey A. Vedyagin, Ilya V. Mishakov, Yury V. Shubin, Olga V. Netskina

    Chlorine- and nitrogen-containing carbon nanofibers (CNFs) were obtained by combined catalytic pyrolysis of trichloroethylene (C2HCl3) and acetonitrile (CH3CN). Their efficiency in the adsorption of 1,2-dichlorobenzene (1,2-DCB) from water has been studied. The synthesis of CNFs was carried out over self-dispersing nickel catalyst at 600 °C. The produced CNFs possess a well-defined segmented structure, high specific surface area (~300 m2/g) and high porosity (0.5–0.7 cm3/g). The addition of CH3CN into the reaction mixture allows the introduction of nitrogen into the CNF structure and increases the volume of mesopores. As a result, the capacity of CNF towards adsorption of 1,2-DCB from its aqueous solution increased from 0.41 to 0.57 cm3/g. Regardless of the presence of N, the CNF samples exhibited a degree of 1,2-DCB adsorption from water–organic emulsion exceeding 90%. The adsorption process was shown to be well described by the Dubinin–Astakhov equation. The regeneration of the used CNF adsorbent through liquid-phase hydrodechlorination was also investigated. For this purpose, Pd nanoparticles (1.5 wt%) were deposited on the CNF surface to form the adsorbent with catalytic function. The presence of palladium was found to have a slight effect on the adsorption capacity of CNF. Further regeneration of the adsorbent-catalyst via hydrodechlorination of adsorbed 1,2-DCB was completed within 1 h with 100% conversion. The repeated use of regenerated adsorbent-catalysts for purification of solutions after the first cycle of adsorption ensures almost complete removal of 1,2-DCB.


  • The Features of the CCVD of Trichloroethylene Over Microdispersed Ni and Ni–Mo Catalysts

    by Arina R. Potylitsyna, Yury I. Bauman, Ilya V. Mishakov, Pavel E. Plyusnin, Aleksey A. Vedyagin, Yury V. Shubin


  • Open Access

    Two Scenarios of Dechlorination of the Chlorinated Hydrocarbons over Nickel-Alumina Catalyst

    by Ilya V. Mishakov, Aleksey A. Vedyagin, Yury I. Bauman, Arina R. Potylitsyna, Anastasiya S. Kadtsyna, Vladimir V. Chesnokov, Anton Yu. Nalivaiko, Alexander A. Gromov, Roman A. Buyanov

    Dechlorination processes attract great interest since they are involved in environmental protection and waste disposal technologies. In this paper, the process of gas-phase dechlorination of 1,2-dichloroethane, chloroform, and chlorobenzene over Ni/Al2O3 catalyst (90 wt% Ni) prepared by a coprecipitation technique was investigated. The reduction behavior of the oxide precursor NiO/Al2O3 was studied by thermogravimetric analysis in a hydrogen medium. A thermodynamic assessment of the conditions under which metallic nickel undergoes deactivation due to the formation of nickel chloride was performed. The dechlorination of chlorinated substrates was studied using a gravimetric flow-through system equipped with McBain balances in a wide range of temperatures (350–650 °C) and hydrogen concentrations (0–98 vol%). The impact of these parameters on selectivity towards the products of hydrodechlorination (C2H4, C2H6, and C6H6) and catalytic pyrolysis (carbon nanomaterial and CH4) was explored. The relationship between the mechanisms of the catalytic hydrodechlorination and the carbide cycle was discussed, and the specific reaction conditions for the implementation of both scenarios were revealed. According to the electron microscopy data, the carbonaceous products deposited on nickel particles during catalytic pyrolysis are represented by nanofibers with a disordered structure formed due to the peculiarity of the process including the side carbon methanation reaction.