Hasan Donat Yildizay
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hasan Donat Yildizay has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Fatih Sen
Sen Research Group, Department of Biochemistry, Dumlupinar University, Kütahya, Turkey
3 shared publications - Muhammed Bekmezci
Sen Research Group, Department of Biochemistry, Dumlupinar University, Kutahya, Türkiye
2 shared publications - Ahmet Esiyok
Kutahya Dumlupinar University, Evliya Celebi Campus
1 shared publication Busra Kokoglu
Sen Research Group, Department of Biochemistry, Dumlupinar University, Kütahya, Turkey
1 shared publicationI. Y. Uralcan
Mechanical Engineering Faculty, Istanbul Technical University, Istanbul, Türkiye
1 shared publication- Nil Aras
Department of Industrial Engineering, Eskişehir Technical University, 26555 Eskişehir, Turkey
1 shared publication
Latest Publications
- Open Access
- 1 August 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (34) , 27848-27863
Nanoengineered Pt–V catalysts promote efficient methanol oxidation in carbon nanotubes
In parallel with the developments in the field of energy, research on fuel cells, a renewable energy source, has accelerated.
- 1 August 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (34) , 27848-27863
Open AccessNanoengineered Pt–V catalysts promote efficient methanol oxidation in carbon nanotubes
In parallel with the developments in the field of energy, research on fuel cells, a renewable energy source, has accelerated.
- Open Access
- 25 March 2025
- Published by Kütahya Dumlupinar Üniversitesi in Journal of Scientific Reports-A
- No. 060,p. 126-149
Nanofluids and engineering applications: A review
With the development of technology, the search for advanced materials has accelerated. Nanomaterials have emerged as an important material group in this search and have found a place for themselves in many different areas. Nanofluids, which are formed by dispersing nanoparticles in basic liquids such as water, ethylene glycol, or oils, have emerged as a very innovative method in the applications of nanoparticles. They have also found a wide range of applications. The improved thermophysical properties of nanofluids have made this research area important in engineering. Nanofluids have gained a unique area, especially in cooling and lubrication systems due to their higher thermal conductivity, viscosity, and convective heat transfer properties compared to traditional liquids. Nanofluids also hold promises in solar energy systems, defense industry systems, nuclear plants, biomedical applications, automotive, and aviation industries where efficient cooling is important. It has also been shown that the use of nanofluids in processing and lubrication processes increases product quality and minimizes wear. Despite these benefits, problems such as stability, cost, and long-term performance in nanofluids continue. These challenges continue to be investigated with a focus on optimizing nanoparticle concentration, developing dispersion methods, and analyzing the environmental impact of nanofluids. Computational and experimental studies will help to understand the flow behavior and heat transfer processes of nanofluids under different operating conditions. The aim of this paper is to review existing nanofluid studies. It provides an overview of the current developments and applications in the field of engineering, focusing on their functions in heat transfer, energy systems and industrial processes.
- 25 March 2025
- Published by Kütahya Dumlupinar Üniversitesi in Journal of Scientific Reports-A
- No. 060,p. 126-149
Open AccessNanofluids and engineering applications: A review
With the development of technology, the search for advanced materials has accelerated. Nanomaterials have emerged as an important material group in this search and have found a place for themselves in many different areas. Nanofluids, which are formed by dispersing nanoparticles in basic liquids such as water, ethylene glycol, or oils, have emerged as a very innovative method in the applications of nanoparticles. They have also found a wide range of applications. The improved thermophysical properties of nanofluids have made this research area important in engineering. Nanofluids have gained a unique area, especially in cooling and lubrication systems due to their higher thermal conductivity, viscosity, and convective heat transfer properties compared to traditional liquids. Nanofluids also hold promises in solar energy systems, defense industry systems, nuclear plants, biomedical applications, automotive, and aviation industries where efficient cooling is important. It has also been shown that the use of nanofluids in processing and lubrication processes increases product quality and minimizes wear. Despite these benefits, problems such as stability, cost, and long-term performance in nanofluids continue. These challenges continue to be investigated with a focus on optimizing nanoparticle concentration, developing dispersion methods, and analyzing the environmental impact of nanofluids. Computational and experimental studies will help to understand the flow behavior and heat transfer processes of nanofluids under different operating conditions. The aim of this paper is to review existing nanofluid studies. It provides an overview of the current developments and applications in the field of engineering, focusing on their functions in heat transfer, energy systems and industrial processes.
- 5 August 2023
- Published by Springer Nature in International Journal of Environmental Science and Technology
- Vol. 20 (10) , 11231-11238
Investigation of energy efficiency of heating systems in power plant boilers for different conditions with CFD analysis
- 5 August 2023
- Published by Springer Nature in International Journal of Environmental Science and Technology
- Vol. 20 (10) , 11231-11238
Investigation of energy efficiency of heating systems in power plant boilers for different conditions with CFD analysis
- 5 October 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (1) , 11635-11649
Experimental investigation of coal and pellet combustion in a manual loaded stove
Manufacture of burn-efficient automatic feed boilers and stoves is made in Turkey for the use of Pellet fuel for heating purposes. In rural areas where regional or central heating systems are not available and natural gas cannot be used, manually loaded stoves are widely used as individual heating systems. Manually loaded stoves, coal and wood are generally used as fuel and ignition of coal is done with wood pieces. In this study, the use of pellet and coal fuels in a manually loaded stove is experimentally investigated. Stove efficiency and emission values for three different combustion conditions (coal-pellet, coal, pellet) in manually loaded stoves were experimentally compared according to BS EN 13240 (Roomheaters Fired by Solid Fuel-Requirements and Test Methods) standard. Stove efficiency was calculated using the measurements made for each fuel. The efficiency obtained as a result of the experiments were calculated as 45.14%, 44.77%, and 44.11% for coal, pellet + coal and pellet, respectively. Due to the high amount of volatile matter in the pellet fuel and the incomplete combustion of volatile substances, the flue gas temperature and CO concentration become high and the stove efficiency decreases. In spite of this, in pellet burning, the amount of particulate matter under the bed in ash is less than the coal burning, which increases the stove efficiency slightly.
- 5 October 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (1) , 11635-11649
Experimental investigation of coal and pellet combustion in a manual loaded stove
Manufacture of burn-efficient automatic feed boilers and stoves is made in Turkey for the use of Pellet fuel for heating purposes. In rural areas where regional or central heating systems are not available and natural gas cannot be used, manually loaded stoves are widely used as individual heating systems. Manually loaded stoves, coal and wood are generally used as fuel and ignition of coal is done with wood pieces. In this study, the use of pellet and coal fuels in a manually loaded stove is experimentally investigated. Stove efficiency and emission values for three different combustion conditions (coal-pellet, coal, pellet) in manually loaded stoves were experimentally compared according to BS EN 13240 (Roomheaters Fired by Solid Fuel-Requirements and Test Methods) standard. Stove efficiency was calculated using the measurements made for each fuel. The efficiency obtained as a result of the experiments were calculated as 45.14%, 44.77%, and 44.11% for coal, pellet + coal and pellet, respectively. Due to the high amount of volatile matter in the pellet fuel and the incomplete combustion of volatile substances, the flue gas temperature and CO concentration become high and the stove efficiency decreases. In spite of this, in pellet burning, the amount of particulate matter under the bed in ash is less than the coal burning, which increases the stove efficiency slightly.
- Open Access
- 2 December 2020
- Published by Punjab University Press in Pakistan Journal of Statistics and Operation Research
- Vol. 16 (4) , 635-648
Optimum Method for Determining Weibull Distribution Parameters Used in Wind Energy Estimation
One of the well-known methods for the determination of wind energy potential is the two-parameter Weibull distribution. It is clear that the success of the Weibull distribution for wind energy applications depends on the estimation of the parameters which can be determined by using various numerical methods. In the present study, Monte Carlo simulation method is performed by using six parameters estimation method that is used in the estimation of Weibull distribution parameters such as Maximum Likelihood Estimation (MLE), Least Squares Method (LSM), Method of Moments (MOM), Method of Logarithmic Moments (MLM), Percentile Method (PM), and L-Moment Method (LM), and is compared to Mean Squared Error (MSE) and Mean Absolute Percentage Error (MAPE). In this study, the wind energy potential of the Meşelik region in Eskişehir was modeled with two-parameter Weibull distribution. The average wind speed (m/s) data, which are gathered in 10-minute intervals from the measuring device installed 10 meters about the ground in Meşelik Campus of Eskişehir Osmangazi University, is used. As a result of the simulation study, it has been determined that MLE is the best parameter estimation method for two-parameter Weibull distribution in large sample sizes, and LM has the closest performance to MLE. The wind speed (m/h) data of the region has been successfully modeled with two-parameter Weibull distribution and the highest average wind power density has been obtained in July as 49.38295 (W/m2) while the lowest average wind power density has been obtained in October as 19.30044 (W/m2).
- 2 December 2020
- Published by Punjab University Press in Pakistan Journal of Statistics and Operation Research
- Vol. 16 (4) , 635-648
Open AccessOptimum Method for Determining Weibull Distribution Parameters Used in Wind Energy Estimation
One of the well-known methods for the determination of wind energy potential is the two-parameter Weibull distribution. It is clear that the success of the Weibull distribution for wind energy applications depends on the estimation of the parameters which can be determined by using various numerical methods. In the present study, Monte Carlo simulation method is performed by using six parameters estimation method that is used in the estimation of Weibull distribution parameters such as Maximum Likelihood Estimation (MLE), Least Squares Method (LSM), Method of Moments (MOM), Method of Logarithmic Moments (MLM), Percentile Method (PM), and L-Moment Method (LM), and is compared to Mean Squared Error (MSE) and Mean Absolute Percentage Error (MAPE). In this study, the wind energy potential of the Meşelik region in Eskişehir was modeled with two-parameter Weibull distribution. The average wind speed (m/s) data, which are gathered in 10-minute intervals from the measuring device installed 10 meters about the ground in Meşelik Campus of Eskişehir Osmangazi University, is used. As a result of the simulation study, it has been determined that MLE is the best parameter estimation method for two-parameter Weibull distribution in large sample sizes, and LM has the closest performance to MLE. The wind speed (m/h) data of the region has been successfully modeled with two-parameter Weibull distribution and the highest average wind power density has been obtained in July as 49.38295 (W/m2) while the lowest average wind power density has been obtained in October as 19.30044 (W/m2).