Michael L. Kerber
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Michael L. Kerber has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Irina Yu. Gorbunova
Department of Plastics Processing Technology, D. Mendeleev University of Chemical Technology of Russia, 9 Miusskaya Square, 125047 Moscow, Russia
5 shared publications - Sergey Olegovich Ilyin
A.V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 29 Leninsky prospect, 119991 Moscow, Russia
5 shared publications - Svetlana O. Ilyina
A.V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 29 Leninsky prospect, 119991 Moscow, Russia
3 shared publications - Anna Kostyuk
A.V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 29 Leninsky prospect, 119991 Moscow, Russia
2 shared publications - Svetlana O. Ilyina
A.V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 29 Leninsky prospect, 119991 Moscow, Russia
2 shared publications - Anastasiya Y. Yadykova
A.V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 29 Leninsky prospect, 119991 Moscow, Russia
1 shared publication
Latest Publications
- Open Access
Nanosilica Gel-Stabilized Phase-Change Materials Based on Epoxy Resin and Wood’s Metal
The emulsification of a molten fusible metal alloy in a liquid epoxy matrix with its subsequent curing is a novel way to create a highly concentrated phase-change material. However, numerous challenges have arisen. The high interfacial tension between the molten metal and epoxy resin and the difference in their viscosities hinder the stretching and breaking of metal droplets during stirring. Further, the high density of metal droplets and lack of suitable surfactants lead to their rapid coalescence and sedimentation in the non-cross-linked resin. Finally, the high differences in the thermal expansion coefficients of the metal alloy and cross-linked epoxy polymer may cause cracking of the resulting phase-change material. This work overcomes the above problems by using nanosilica-induced physical gelation to thicken the epoxy medium containing Wood’s metal, stabilize their interfacial boundary, and immobilize the molten metal droplets through the creation of a gel-like network with a yield stress. In turn, the yield stress and the subsequent low-temperature curing with diethylenetriamine prevent delamination and cracking, while the transformation of the epoxy resin as a physical gel into a cross-linked polymer gel ensures form stability. The stabilization mechanism is shown to combine Pickering-like interfacial anchoring of hydrophilic silica at the metal/epoxy boundary with bulk gelation of the epoxy phase, enabling high metal loadings. As a result, epoxy shape-stable phase-change materials containing up to 80 wt% of Wood’s metal were produced. Wood’s metal forms fine dispersed droplets in epoxy medium with an average size of 2–5 µm, which can store thermal energy with an efficiency of up to 120.8 J/cm3. Wood’s metal plasticizes the epoxy matrix and decreases its glass transition temperature because of interactions with the epoxy resin and its hardener. However, the reinforcing effect of the metal particles compensates for this adverse effect, increasing Young’s modulus of the cured phase-change system up to 825 MPa. These form-stable, high-energy-density composites are promising for thermal energy storage in building envelopes, radiation-protective shielding, or industrial heat management systems where leakage-free operation and mechanical integrity are critical.
Open AccessNanosilica Gel-Stabilized Phase-Change Materials Based on Epoxy Resin and Wood’s Metal
The emulsification of a molten fusible metal alloy in a liquid epoxy matrix with its subsequent curing is a novel way to create a highly concentrated phase-change material. However, numerous challenges have arisen. The high interfacial tension between the molten metal and epoxy resin and the difference in their viscosities hinder the stretching and breaking of metal droplets during stirring. Further, the high density of metal droplets and lack of suitable surfactants lead to their rapid coalescence and sedimentation in the non-cross-linked resin. Finally, the high differences in the thermal expansion coefficients of the metal alloy and cross-linked epoxy polymer may cause cracking of the resulting phase-change material. This work overcomes the above problems by using nanosilica-induced physical gelation to thicken the epoxy medium containing Wood’s metal, stabilize their interfacial boundary, and immobilize the molten metal droplets through the creation of a gel-like network with a yield stress. In turn, the yield stress and the subsequent low-temperature curing with diethylenetriamine prevent delamination and cracking, while the transformation of the epoxy resin as a physical gel into a cross-linked polymer gel ensures form stability. The stabilization mechanism is shown to combine Pickering-like interfacial anchoring of hydrophilic silica at the metal/epoxy boundary with bulk gelation of the epoxy phase, enabling high metal loadings. As a result, epoxy shape-stable phase-change materials containing up to 80 wt% of Wood’s metal were produced. Wood’s metal forms fine dispersed droplets in epoxy medium with an average size of 2–5 µm, which can store thermal energy with an efficiency of up to 120.8 J/cm3. Wood’s metal plasticizes the epoxy matrix and decreases its glass transition temperature because of interactions with the epoxy resin and its hardener. However, the reinforcing effect of the metal particles compensates for this adverse effect, increasing Young’s modulus of the cured phase-change system up to 825 MPa. These form-stable, high-energy-density composites are promising for thermal energy storage in building envelopes, radiation-protective shielding, or industrial heat management systems where leakage-free operation and mechanical integrity are critical.
- Open Access
Epoxy Resin Highly Loaded with an Ionic Liquid: Morphology, Rheology, and Thermophysical Properties
An epoxy resin can be crosslinked with an imidazole-based ionic liquid (IL), whose excess, provided its high melting temperature, can potentially form a dispersed phase to store thermal energy and produce a phase-change material (PCM). This work investigates the crosslinking of diglycidyl ether of bisphenol A (DGEBA) using 1-ethyl-3-methylimidazolium chloride ([EMIM]Cl) at its mass fractions of 5, 10, 20, 40, and 60%. The effect of [EMIM]Cl on the viscosity, curing rate, and curing degree was studied, and the thermophysical properties and morphology of the resulting crosslinked epoxy polymer were investigated. During the curing, [EMIM]Cl changes its role from a crosslinking agent (an initiator of homopolymerization) and a diluent of the epoxy resin to a plasticizer of the cured epoxy polymer and a dispersed phase-change agent. An increase in the [EMIM]Cl content accelerates the curing firstly because of the growth in the number of reaction centers, and then the curing slows down because of the action of the IL as a diluent, which reduces the concentration of reacting substances. In addition, a rise in the proportion of [EMIM]Cl led to the predominance of the initiation over the chain growth, causing the formation of short non-crosslinked molecules. The IL content of 5% allowed for curing the epoxy resin and elevating the stiffness of the crosslinked product by almost 7 times compared to tetraethylenetriamine as a usual aliphatic amine hardener (6.95 GPa versus 1.1 GPa). The [EMIM]Cl content of 20–40% resulted in a thermoplastic epoxy polymer capable of flowing and molding at elevated temperatures. The formation of IL emulsion in the epoxy matrix occurred at 60% [EMIM]Cl, but its hygroscopicity and absorption of water from surrounding air reduced the crystallinity of dispersed [EMIM]Cl, not allowing for an effective phase-change material to be obtained.
Open AccessEpoxy Resin Highly Loaded with an Ionic Liquid: Morphology, Rheology, and Thermophysical Properties
An epoxy resin can be crosslinked with an imidazole-based ionic liquid (IL), whose excess, provided its high melting temperature, can potentially form a dispersed phase to store thermal energy and produce a phase-change material (PCM). This work investigates the crosslinking of diglycidyl ether of bisphenol A (DGEBA) using 1-ethyl-3-methylimidazolium chloride ([EMIM]Cl) at its mass fractions of 5, 10, 20, 40, and 60%. The effect of [EMIM]Cl on the viscosity, curing rate, and curing degree was studied, and the thermophysical properties and morphology of the resulting crosslinked epoxy polymer were investigated. During the curing, [EMIM]Cl changes its role from a crosslinking agent (an initiator of homopolymerization) and a diluent of the epoxy resin to a plasticizer of the cured epoxy polymer and a dispersed phase-change agent. An increase in the [EMIM]Cl content accelerates the curing firstly because of the growth in the number of reaction centers, and then the curing slows down because of the action of the IL as a diluent, which reduces the concentration of reacting substances. In addition, a rise in the proportion of [EMIM]Cl led to the predominance of the initiation over the chain growth, causing the formation of short non-crosslinked molecules. The IL content of 5% allowed for curing the epoxy resin and elevating the stiffness of the crosslinked product by almost 7 times compared to tetraethylenetriamine as a usual aliphatic amine hardener (6.95 GPa versus 1.1 GPa). The [EMIM]Cl content of 20–40% resulted in a thermoplastic epoxy polymer capable of flowing and molding at elevated temperatures. The formation of IL emulsion in the epoxy matrix occurred at 60% [EMIM]Cl, but its hygroscopicity and absorption of water from surrounding air reduced the crystallinity of dispersed [EMIM]Cl, not allowing for an effective phase-change material to be obtained.
- Open Access
Naphthalene-Containing Epoxy Resin: Phase Structure, Rheology, and Thermophysical Properties
Naphthalene is a fungicide that can also be a phase-change agent owing to its high crystallization enthalpy at about 80 °C. The relatively rapid evaporation of naphthalene as a fungicide and its shape instability after melting are problems solved in this work by its placement into a cured epoxy matrix. The work’s research materials included diglycidyl ether of bisphenol A as an epoxy resin, 4,4′-diaminodiphenyl sulfone as its hardener, and naphthalene as a phase-change agent or a fungicide. Their miscibility was investigated by laser interferometry, the rheological properties of their blends before and during the curing by rotational rheometry, the thermophysical features of the curing process and the resulting phase-change materials by differential scanning calorimetry, and the blends’ morphologies by transmission optical and scanning electron microscopies. Naphthalene and epoxy resin were miscible when heated above 80 °C. This fact allowed obtaining highly concentrated mixtures containing up to 60% naphthalene by high-temperature homogeneous curing with 4,4′-diaminodiphenyl sulfone. The initial solubility of naphthalene was only 19% in uncured epoxy resin but increased strongly upon heating, reducing the viscosity of the reaction mixture, delaying its gelation, and slowing cross-linking. At 20–40% mass fraction of naphthalene, it almost entirely retained its dissolved state after cross-linking as a metastable solution, causing plasticization of the cured epoxy polymer and lowering its glass transition temperature. At 60% naphthalene, about half dissolved within the cured polymer, while the other half formed coarse particles capable of crystallization and thermal energy storage. In summary, the resulting phase-change material stored 42.6 J/g of thermal energy within 62–90 °C and had a glass transition temperature of 46.4 °C at a maximum naphthalene mass fraction of 60% within the epoxy matrix.
Open AccessNaphthalene-Containing Epoxy Resin: Phase Structure, Rheology, and Thermophysical Properties
Naphthalene is a fungicide that can also be a phase-change agent owing to its high crystallization enthalpy at about 80 °C. The relatively rapid evaporation of naphthalene as a fungicide and its shape instability after melting are problems solved in this work by its placement into a cured epoxy matrix. The work’s research materials included diglycidyl ether of bisphenol A as an epoxy resin, 4,4′-diaminodiphenyl sulfone as its hardener, and naphthalene as a phase-change agent or a fungicide. Their miscibility was investigated by laser interferometry, the rheological properties of their blends before and during the curing by rotational rheometry, the thermophysical features of the curing process and the resulting phase-change materials by differential scanning calorimetry, and the blends’ morphologies by transmission optical and scanning electron microscopies. Naphthalene and epoxy resin were miscible when heated above 80 °C. This fact allowed obtaining highly concentrated mixtures containing up to 60% naphthalene by high-temperature homogeneous curing with 4,4′-diaminodiphenyl sulfone. The initial solubility of naphthalene was only 19% in uncured epoxy resin but increased strongly upon heating, reducing the viscosity of the reaction mixture, delaying its gelation, and slowing cross-linking. At 20–40% mass fraction of naphthalene, it almost entirely retained its dissolved state after cross-linking as a metastable solution, causing plasticization of the cured epoxy polymer and lowering its glass transition temperature. At 60% naphthalene, about half dissolved within the cured polymer, while the other half formed coarse particles capable of crystallization and thermal energy storage. In summary, the resulting phase-change material stored 42.6 J/g of thermal energy within 62–90 °C and had a glass transition temperature of 46.4 °C at a maximum naphthalene mass fraction of 60% within the epoxy matrix.
- Open Access
Self-Lubricating and Shape-Stable Phase-Change Materials Based on Epoxy Resin and Vegetable Oils
Palm or coconut oil is capable of dissolving in a mixture of bisphenol A-based epoxy resin and a high-temperature hardener (4,4′-diaminodiphenyl sulfone) when heated and then forms a dispersed phase as a result of cross-linking and molecular weight growth of the epoxy medium. Achieving the temporary miscibility between the curing epoxy matrix and the vegetable oil allows a uniform distribution of vegetable oil droplets in the epoxy medium. This novel approach to creating a dispersed phase-change material made a cured epoxy polymer containing up to 20% oil. The miscibility of epoxy resin and oil was studied by laser interferometry, and phase state diagrams of binary mixtures were calculated according to theory and experiments. A weak effect of oil on the viscosity and kinetics of the epoxy resin curing was demonstrated by rotational rheometry. According to differential scanning calorimetry and dynamic mechanical analysis, the oil plasticizes the epoxy matrix slightly, expanding its glass transition region towards low temperatures and reducing its elastic modulus. In the cured epoxy matrix, oil droplets have a diameter of 3–14 µm and are incapable of complete crystallization due to their multi-component chemical composition and non-disappeared limited miscibility. The obtained phase-change materials have relatively low specific energy capacity but can be used alternatively as self-lubricating low-noise materials due to dispersed oil, high stiffness, and reduced friction coefficient. Palm oil crystallizes more readily, better matching the creation of phase-change materials, whereas coconut oil crystallization is more suppressed, making it better for reducing the friction coefficient of the oil-containing material.
Open AccessSelf-Lubricating and Shape-Stable Phase-Change Materials Based on Epoxy Resin and Vegetable Oils
Palm or coconut oil is capable of dissolving in a mixture of bisphenol A-based epoxy resin and a high-temperature hardener (4,4′-diaminodiphenyl sulfone) when heated and then forms a dispersed phase as a result of cross-linking and molecular weight growth of the epoxy medium. Achieving the temporary miscibility between the curing epoxy matrix and the vegetable oil allows a uniform distribution of vegetable oil droplets in the epoxy medium. This novel approach to creating a dispersed phase-change material made a cured epoxy polymer containing up to 20% oil. The miscibility of epoxy resin and oil was studied by laser interferometry, and phase state diagrams of binary mixtures were calculated according to theory and experiments. A weak effect of oil on the viscosity and kinetics of the epoxy resin curing was demonstrated by rotational rheometry. According to differential scanning calorimetry and dynamic mechanical analysis, the oil plasticizes the epoxy matrix slightly, expanding its glass transition region towards low temperatures and reducing its elastic modulus. In the cured epoxy matrix, oil droplets have a diameter of 3–14 µm and are incapable of complete crystallization due to their multi-component chemical composition and non-disappeared limited miscibility. The obtained phase-change materials have relatively low specific energy capacity but can be used alternatively as self-lubricating low-noise materials due to dispersed oil, high stiffness, and reduced friction coefficient. Palm oil crystallizes more readily, better matching the creation of phase-change materials, whereas coconut oil crystallization is more suppressed, making it better for reducing the friction coefficient of the oil-containing material.
- Open Access
Epoxy Phase-Change Materials Based on Paraffin Wax Stabilized by Asphaltenes
The usual problem of meltable phase-change agents is the instability in their form upon heating, which can be solved by placing them into a continuous polymer matrix. Epoxy resin is a suitable medium for dispersing molten agents, but it is necessary to make the obtained droplets stable during the curing of the formed phase-change material. This work shows that molten paraffin wax forms a Pickering emulsion in an epoxy medium and in the presence of asphaltenes extracted from heavy crude oil. Theoretical calculations revealed the complex equilibrium in the epoxy/wax/asphaltene triple system due to their low mutual solubility. Rheological studies showed the viscoplastic behavior of the obtained dispersions at 25 °C, which disappears upon the heating and melting of the paraffin phase. Wax and asphaltenes increased the viscosity of the epoxy medium during its curing but did not inhibit cross-linking or reduce the glass transition temperature of the cured polymer. As a result of curing, it is possible to obtain phase-change materials containing up to 45% paraffin wax that forms a dispersed phase with a size of 0.2–6.5 μm. The small size of dispersed wax can decrease its degree of crystallinity to 13–29% of its original value, reducing the efficiency of the phase-change material.
Open AccessEpoxy Phase-Change Materials Based on Paraffin Wax Stabilized by Asphaltenes
The usual problem of meltable phase-change agents is the instability in their form upon heating, which can be solved by placing them into a continuous polymer matrix. Epoxy resin is a suitable medium for dispersing molten agents, but it is necessary to make the obtained droplets stable during the curing of the formed phase-change material. This work shows that molten paraffin wax forms a Pickering emulsion in an epoxy medium and in the presence of asphaltenes extracted from heavy crude oil. Theoretical calculations revealed the complex equilibrium in the epoxy/wax/asphaltene triple system due to their low mutual solubility. Rheological studies showed the viscoplastic behavior of the obtained dispersions at 25 °C, which disappears upon the heating and melting of the paraffin phase. Wax and asphaltenes increased the viscosity of the epoxy medium during its curing but did not inhibit cross-linking or reduce the glass transition temperature of the cured polymer. As a result of curing, it is possible to obtain phase-change materials containing up to 45% paraffin wax that forms a dispersed phase with a size of 0.2–6.5 μm. The small size of dispersed wax can decrease its degree of crystallinity to 13–29% of its original value, reducing the efficiency of the phase-change material.
- Open Access
The Curing Rheokinetics of Epoxyphosphazene Binders
The influence of epoxyphosphazene-modifying additives on the features of the hot curing process of epoxy-amine composition was studied by the rotational viscometry method. The modification caused an acceleration of the curing process, changed rheokinetics of viscosity increase, especially the stage molecular mass growth of linear chains became almost twice shorter for composition with 30% modifier than for unmodified one. We suggest the reason for these changes is the polyfunctionality of epoxyphosphazene, which finally results in high-density network formation. In cold curing process the bulkiness of epoxyphosphazene molecule and the lack of heat for its motion results in incomplete cure. Thus, in order to cope with these difficulties hot curing systems were proposed and studied.
Open AccessThe Curing Rheokinetics of Epoxyphosphazene Binders
The influence of epoxyphosphazene-modifying additives on the features of the hot curing process of epoxy-amine composition was studied by the rotational viscometry method. The modification caused an acceleration of the curing process, changed rheokinetics of viscosity increase, especially the stage molecular mass growth of linear chains became almost twice shorter for composition with 30% modifier than for unmodified one. We suggest the reason for these changes is the polyfunctionality of epoxyphosphazene, which finally results in high-density network formation. In cold curing process the bulkiness of epoxyphosphazene molecule and the lack of heat for its motion results in incomplete cure. Thus, in order to cope with these difficulties hot curing systems were proposed and studied.