David Kusmič
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
David Kusmič has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Lenka Klakurková
CEITEC Brno University of Technology
2 shared publications- Ondrej Cech
Brno University of Technology
2 shared publications - Andrzej Trytek
Faculty of Mechanics and Technology, Rzeszow University of Technology, 37-450 Stalowa Wola, Poland
1 shared publication D. Trochta
1 shared publication- Jan Drábek
University of Defence
1 shared publication - Jan Zouhar
Brno University of Technology
1 shared publication
Latest Publications
- Open Access
- 22 June 2026
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 76 (4) , 605-613
Impact Resistance of ER68 Thermoset and TH110 Thermoplastic Para-Aramid Composite Panels
This study evaluates the mechanical properties and ballistic resistance of composite panels fabricated from para-aramid fabric Twaron CT 747, impregnated with two distinct polymer matrices. Thermoset composites (TS) with an ER68 matrix and thermoplastic composites (TP) with a TH110 matrix were produced, each containing a matrix volume fraction of 20 %. The manufacturing process employed autoclave curing for TS specimens and hot-pressing for TP specimens. The mechanical properties were assessed through Shore D hardness measurements, tensile testing, and three-point bending tests. Ballistic resistance was evaluated via the static detonation of a 152 mm high-explosive fragmentation artillery shell, with the extent of damage analysed using X-ray computed tomography (XCT) and scanning electron microscopy (SEM). The results indicated that TS specimens exhibited 35.7 % higher Shore D surface hardness and 6.9 % greater tensile strength than TP panels. Additionally, the flexural strength of TS specimens was 93.8 % higher than that of TP specimens. Ballistic testing confirmed distinct damage mechanisms dependent on the type of polymer matrix, with TP panels demonstrating superior resistance to fragmentation loading. These findings contribute to a more comprehensive understanding of the probable influence of polymer matrices and processing conditions on the mechanical performance and protective capabilities of composite materials designed for ballistic applications.
- 22 June 2026
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 76 (4) , 605-613
Open AccessImpact Resistance of ER68 Thermoset and TH110 Thermoplastic Para-Aramid Composite Panels
This study evaluates the mechanical properties and ballistic resistance of composite panels fabricated from para-aramid fabric Twaron CT 747, impregnated with two distinct polymer matrices. Thermoset composites (TS) with an ER68 matrix and thermoplastic composites (TP) with a TH110 matrix were produced, each containing a matrix volume fraction of 20 %. The manufacturing process employed autoclave curing for TS specimens and hot-pressing for TP specimens. The mechanical properties were assessed through Shore D hardness measurements, tensile testing, and three-point bending tests. Ballistic resistance was evaluated via the static detonation of a 152 mm high-explosive fragmentation artillery shell, with the extent of damage analysed using X-ray computed tomography (XCT) and scanning electron microscopy (SEM). The results indicated that TS specimens exhibited 35.7 % higher Shore D surface hardness and 6.9 % greater tensile strength than TP panels. Additionally, the flexural strength of TS specimens was 93.8 % higher than that of TP specimens. Ballistic testing confirmed distinct damage mechanisms dependent on the type of polymer matrix, with TP panels demonstrating superior resistance to fragmentation loading. These findings contribute to a more comprehensive understanding of the probable influence of polymer matrices and processing conditions on the mechanical performance and protective capabilities of composite materials designed for ballistic applications.
- 30 November 2021
- Published by The Electrochemical Society in ECS Transactions
- Vol. 105 (1) , 329-337
The Corrosion Resistance of Hard Anodised EN AW 7075 T6 Alloy
In this paper, commercially cold-rolled and artificial aged EN AW 7075 T6 alloy has been used. To ensure increased corrosion resistance, surface hardness, scratching resistance, and aesthetic features, this aluminium alloy was subsequently hard anodised and hot-water sealed (AC-A). The hard anodizing and sealing process increased surface hardness up to 304±13 HV 1 from an initial surface hardness of 194±3 HV 1. Also, the microhardness of the anodised layer and bulk material has been documented. Scanning electron microscopy (SEM) was used for microstructure and trapped precipitates investigation in the 42.9±1.4 thick formed anodised layer investigation. The T6 treated (AC) and hard anodised together with sealed (AC-A) EN AW 7075 alloy corrosion properties were evaluated using the anodic potentiodynamic polarisation tests (PPT) in a neutral 2.5% NaCl deaerated solution. The corrosion rate CR (mm/y) decreased approx. 39-times for the hard anodised and sealed EN AW 7075 alloy (AC-A), associated with the shift of the Ecorr (mV) to more positive values, degreased Icorr (µA) and increased Rp (Ohm) values compared to the artificial aged (AC) alloy. Additionally, the pitting was evaluated using laser confocal microscopy, and the pitting coefficient was also calculated.
- 30 November 2021
- Published by The Electrochemical Society in ECS Transactions
- Vol. 105 (1) , 329-337
The Corrosion Resistance of Hard Anodised EN AW 7075 T6 Alloy
In this paper, commercially cold-rolled and artificial aged EN AW 7075 T6 alloy has been used. To ensure increased corrosion resistance, surface hardness, scratching resistance, and aesthetic features, this aluminium alloy was subsequently hard anodised and hot-water sealed (AC-A). The hard anodizing and sealing process increased surface hardness up to 304±13 HV 1 from an initial surface hardness of 194±3 HV 1. Also, the microhardness of the anodised layer and bulk material has been documented. Scanning electron microscopy (SEM) was used for microstructure and trapped precipitates investigation in the 42.9±1.4 thick formed anodised layer investigation. The T6 treated (AC) and hard anodised together with sealed (AC-A) EN AW 7075 alloy corrosion properties were evaluated using the anodic potentiodynamic polarisation tests (PPT) in a neutral 2.5% NaCl deaerated solution. The corrosion rate CR (mm/y) decreased approx. 39-times for the hard anodised and sealed EN AW 7075 alloy (AC-A), associated with the shift of the Ecorr (mV) to more positive values, degreased Icorr (µA) and increased Rp (Ohm) values compared to the artificial aged (AC) alloy. Additionally, the pitting was evaluated using laser confocal microscopy, and the pitting coefficient was also calculated.
- 30 November 2021
- Published by The Electrochemical Society in ECS Transactions
- Vol. 105 (1) , 231-238
Inverse Vulcanisation of Sulfur - Preparation Methods and Applications
In this paper, we present a general overview of the development of the sulfur-based polymers that have been synthesized by inverse vulcanization and therefore they are collectively referred to as inverse vulcanized sulfur. The method of inverse vulcanization was introduced in 2013. Since then many different samples of inverse vulcanized sulfur with different properties have been synthesized. At the same time, various practical applications were introduced, including the possibility of using inverse vulcanized sulfur as the active material of the Li-S batteries.
- 30 November 2021
- Published by The Electrochemical Society in ECS Transactions
- Vol. 105 (1) , 231-238
Inverse Vulcanisation of Sulfur - Preparation Methods and Applications
In this paper, we present a general overview of the development of the sulfur-based polymers that have been synthesized by inverse vulcanization and therefore they are collectively referred to as inverse vulcanized sulfur. The method of inverse vulcanization was introduced in 2013. Since then many different samples of inverse vulcanized sulfur with different properties have been synthesized. At the same time, various practical applications were introduced, including the possibility of using inverse vulcanized sulfur as the active material of the Li-S batteries.
- 25 November 2020
- Published by The Electrochemical Society in ECS Transactions
- Vol. 99 (1) , 231-239
Corrosion Resistance of Plasma Nitrided Austenitic Stainless Steel AISI 304 (X5CrNi18-10)
In this paper, austenitic stainless steel AISI 304 (X5CrNi 18-10) has been subjected to low-temperature plasma nitriding (LTPN) at 400°C (673 K) in 24H2:8N2 (l/h), and in 8H2:24N2 (l/h) marked as LTPN-R, and to high-temperature plasma nitriding (HTPN) at 550°C (823 K) in 24H2:8N2 (l/h) working atmosphere, for 15h. The microstructure, microhardness, and phase evaluation of the nitrided steel were studied. The PN led to significant microhardness increase from 206 ± 3 HV0.05 to 842 ± 27 HV0.05 (LTPN), 821 ± 18 HV0.05 (LTPN-R), resp. to 1246 ± 27 HV0.05 (HTPN). The corrosion properties were evaluated using the anodic potentiodynamic polarization tests in neutral 2.5% NaCl deaerated solution. The corrosion rate CR (mm.a-1) increased only slightly for LTPN procedures. But using the HTPN increased 43-times to untreated steel, due to reduced passivation ability by chromium depletion by formed CrN. Additionally, the pitting was evaluated, and the pitting coefficient was calculated.
- 25 November 2020
- Published by The Electrochemical Society in ECS Transactions
- Vol. 99 (1) , 231-239
Corrosion Resistance of Plasma Nitrided Austenitic Stainless Steel AISI 304 (X5CrNi18-10)
In this paper, austenitic stainless steel AISI 304 (X5CrNi 18-10) has been subjected to low-temperature plasma nitriding (LTPN) at 400°C (673 K) in 24H2:8N2 (l/h), and in 8H2:24N2 (l/h) marked as LTPN-R, and to high-temperature plasma nitriding (HTPN) at 550°C (823 K) in 24H2:8N2 (l/h) working atmosphere, for 15h. The microstructure, microhardness, and phase evaluation of the nitrided steel were studied. The PN led to significant microhardness increase from 206 ± 3 HV0.05 to 842 ± 27 HV0.05 (LTPN), 821 ± 18 HV0.05 (LTPN-R), resp. to 1246 ± 27 HV0.05 (HTPN). The corrosion properties were evaluated using the anodic potentiodynamic polarization tests in neutral 2.5% NaCl deaerated solution. The corrosion rate CR (mm.a-1) increased only slightly for LTPN procedures. But using the HTPN increased 43-times to untreated steel, due to reduced passivation ability by chromium depletion by formed CrN. Additionally, the pitting was evaluated, and the pitting coefficient was calculated.