Hao Dinh Duong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hao Dinh Duong has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Tra Hung Tran
Department of Mechanical Engineering, School of Engineering and Technology, Nha Trang University, Khanh Hoa, Vietnam
11 shared publicationsMasakazu Okazaki
Niigata Institute of Technology
5 shared publicationsNam Hoai Quach
Faculty of Transportation Engineering, Nha Trang University, Nha Trang 650000, Vietnam
5 shared publicationsDac Dung Truong
Department of Engineering Mechanics, Nha Trang University, Nha Trang, Vietnam
4 shared publicationsQuan Minh Nguyen
Department of Mechanical Engineering, School of Engineering and Technology, Nha Trang University, Khanh Hoa, Vietnam
4 shared publications- Tra Hung Tran
Department of Mechanical Engineering, School of Engineering and Technology, Nha Trang University
3 shared publications
Latest Publications
- Open Access
- 13 May 2026
- Published by Springer Nature in Research Square
Mechanical Behavior of Dissimilar Friction Stir Welded T-joints between Aluminum Alloy and Steel: Role of Kissing Bonds, Intermetallic Compounds, and Microstructural Evolution
This study investigates the mechanical behavior of dissimilar friction stir welded (FSWed) T-joints of AA6061/steel, focusing on the roles of kissing bonds (KBs), intermetallic compounds (IMCs), and microstructural evolution. The T-joints were fabricated at the welding speeds of 100–250 mm/min and characterized by SEM, EDS, XRD and tensile testing for both skin and stringer loading. The finite element analysis was also applied to clarify the fracture behavior of the T-joint. The results show that both KBs and IMCs are unavoidable and strongly dependent on welding conditions. At low welding speeds, thick and brittle IMC layers consisting of Fe 2 Al 5 and FeAl 3 phases, together with interfacial micro-cracks, dominate crack initiation, reducing joint strength despite limited crack opening. At higher speeds, IMC formation is suppressed, but unfavorable KB geometry promotes crack propagation, leading to strength reduction. The stringer strength is significantly lower than the skin strength, indicating that interfacial defects govern failure. Microstructural evolution has a secondary effect, mainly influencing skin behavior. The optimal welding speed is 150 mm/min, where reduced IMC brittleness and favorable KB geometry result in the highest joint strength.
- 13 May 2026
- Published by Springer Nature in Research Square
Open AccessMechanical Behavior of Dissimilar Friction Stir Welded T-joints between Aluminum Alloy and Steel: Role of Kissing Bonds, Intermetallic Compounds, and Microstructural Evolution
This study investigates the mechanical behavior of dissimilar friction stir welded (FSWed) T-joints of AA6061/steel, focusing on the roles of kissing bonds (KBs), intermetallic compounds (IMCs), and microstructural evolution. The T-joints were fabricated at the welding speeds of 100–250 mm/min and characterized by SEM, EDS, XRD and tensile testing for both skin and stringer loading. The finite element analysis was also applied to clarify the fracture behavior of the T-joint. The results show that both KBs and IMCs are unavoidable and strongly dependent on welding conditions. At low welding speeds, thick and brittle IMC layers consisting of Fe 2 Al 5 and FeAl 3 phases, together with interfacial micro-cracks, dominate crack initiation, reducing joint strength despite limited crack opening. At higher speeds, IMC formation is suppressed, but unfavorable KB geometry promotes crack propagation, leading to strength reduction. The stringer strength is significantly lower than the skin strength, indicating that interfacial defects govern failure. Microstructural evolution has a secondary effect, mainly influencing skin behavior. The optimal welding speed is 150 mm/min, where reduced IMC brittleness and favorable KB geometry result in the highest joint strength.
- 11 May 2026
- Published by Trans Tech Publications, Ltd. in Advances in Science and Technology
- Vol. 175, 87-93
Effect of Post-Weld Heat Treatment on Microstructure and Mechanical Properties of Friction Stir Welded T-Joint between AA6061 and Steel
Post-weld heat treatment (PWHT) was investigated to evaluate its effects on dissimilar friction stir welded (FSWed) T-joints of AA6061 and low carbon steel. The non-PWHT joint was compared with four PWHT conditions involving solution treatment, quenching, natural aging, and subsequent artificial aging at 0-12 hours. Microstructural characterization revealed a largely continuous Al/steel interface in the non-PWHT joint, while PWHT promoted interfacial cracking and modified precipitation behavior in the stir zone and heat-affected zone of AA6061. Hardness increased monotonically with aging time, reaching ~95–100 HV after PWHT artificial aging at 12 hours. Tensile strength peaked at 212MPa after 4 hours of artificial aging, while maximum strain decreased from ~9% to ~5.3% after 12 h artificial aging, indicating ductility loss under prolonged aging. Fracture location after PWHT consistently occurred at SZ, highlighting a critical failure region governed by joint geometry and microstructural heterogeneity.
- 11 May 2026
- Published by Trans Tech Publications, Ltd. in Advances in Science and Technology
- Vol. 175, 87-93
Effect of Post-Weld Heat Treatment on Microstructure and Mechanical Properties of Friction Stir Welded T-Joint between AA6061 and Steel
Post-weld heat treatment (PWHT) was investigated to evaluate its effects on dissimilar friction stir welded (FSWed) T-joints of AA6061 and low carbon steel. The non-PWHT joint was compared with four PWHT conditions involving solution treatment, quenching, natural aging, and subsequent artificial aging at 0-12 hours. Microstructural characterization revealed a largely continuous Al/steel interface in the non-PWHT joint, while PWHT promoted interfacial cracking and modified precipitation behavior in the stir zone and heat-affected zone of AA6061. Hardness increased monotonically with aging time, reaching ~95–100 HV after PWHT artificial aging at 12 hours. Tensile strength peaked at 212MPa after 4 hours of artificial aging, while maximum strain decreased from ~9% to ~5.3% after 12 h artificial aging, indicating ductility loss under prolonged aging. Fracture location after PWHT consistently occurred at SZ, highlighting a critical failure region governed by joint geometry and microstructural heterogeneity.
- Open Access
- 1 November 2025
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1565 (1)
Assessment of dissimilar friction stir lap welded AA6061/AA5083 for marine sustainable development
In recent years, the marine industry has created lightweight, corrosion-resistant structures in response to the need for environmentally friendly and energy-efficient solutions that is necessary for sustainable development. In this work, a lightweight structure of dissimilar lap-joint between AA6061 and AA5083 was fabricated using friction stir welding (FSW) technology with various welding speeds. The microstructure and joint strength were analysed and assessed by using microscope and tensile test machine, respectively. The findings emphasised that the distortion of joint is insignificant and no solidification fractures or groove flaws on the smooth welding surfaces. Using high and/or low welding speed would lead to the formation of tunnel defects. It is worthy to note that the hook defect is eliminated in this wok. The specimen produced by the welding speed of 400 mm/min was achieved with the highest strength. The FSWed lap-joint of AA6061/AA5083 has a large potential in marine sustainable development.
- 1 November 2025
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1565 (1)
Open AccessAssessment of dissimilar friction stir lap welded AA6061/AA5083 for marine sustainable development
In recent years, the marine industry has created lightweight, corrosion-resistant structures in response to the need for environmentally friendly and energy-efficient solutions that is necessary for sustainable development. In this work, a lightweight structure of dissimilar lap-joint between AA6061 and AA5083 was fabricated using friction stir welding (FSW) technology with various welding speeds. The microstructure and joint strength were analysed and assessed by using microscope and tensile test machine, respectively. The findings emphasised that the distortion of joint is insignificant and no solidification fractures or groove flaws on the smooth welding surfaces. Using high and/or low welding speed would lead to the formation of tunnel defects. It is worthy to note that the hook defect is eliminated in this wok. The specimen produced by the welding speed of 400 mm/min was achieved with the highest strength. The FSWed lap-joint of AA6061/AA5083 has a large potential in marine sustainable development.
- 8 January 2024
- Published by Taylor & Francis in Welding International
- Vol. 38 (2) , 116-127
Influence of pin profiles on temperature distribution, microstructure evolution and mechanical properties of friction stir welded AA6061
- 8 January 2024
- Published by Taylor & Francis in Welding International
- Vol. 38 (2) , 116-127
Influence of pin profiles on temperature distribution, microstructure evolution and mechanical properties of friction stir welded AA6061
- 1 February 2023
- Published by Taylor & Francis in Welding International
- Vol. 37 (2) , 101-110
Mechanical performance of dissimilar friction stir welded lap-joint between aluminium alloy 6061 and 316 stainless steel
The dissimilar lap-joint of the AA6061 to 316 stainless steel was produced by friction stir welding. Changing microstructure, joint interface, and mechanical performances via welding rate was revealed. A wave interface pattern was found at the low welding rate with free oxide layer. The interface became flat at the high welding rate with the oxide film formation. The diffusion and intermetallic compounds (IMCs) layers were formed on the interface and their thickness decreased via increasing the welding rate. The highest joint strength was obtained at the welding rate of 75 mm/min but strongly reduced with growing the welding rate. The strength was dramatically correlated with the bonding area, diffusion thickness and interface morphology instead of the IMCs layer thickness. At the low welding rate, the joint was fractured via ductile behavior with a lot of dimples found on the fracture surface of 316 stainless steel.
- 1 February 2023
- Published by Taylor & Francis in Welding International
- Vol. 37 (2) , 101-110
Mechanical performance of dissimilar friction stir welded lap-joint between aluminium alloy 6061 and 316 stainless steel
The dissimilar lap-joint of the AA6061 to 316 stainless steel was produced by friction stir welding. Changing microstructure, joint interface, and mechanical performances via welding rate was revealed. A wave interface pattern was found at the low welding rate with free oxide layer. The interface became flat at the high welding rate with the oxide film formation. The diffusion and intermetallic compounds (IMCs) layers were formed on the interface and their thickness decreased via increasing the welding rate. The highest joint strength was obtained at the welding rate of 75 mm/min but strongly reduced with growing the welding rate. The strength was dramatically correlated with the bonding area, diffusion thickness and interface morphology instead of the IMCs layer thickness. At the low welding rate, the joint was fractured via ductile behavior with a lot of dimples found on the fracture surface of 316 stainless steel.
- 3 January 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (20) , 9428-9439
Microstructure Evolution and Interfacial Bonding Properties of Dissimilar T-Lap Joints Using Friction Stir Welding Parameters
- 3 January 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (20) , 9428-9439
Microstructure Evolution and Interfacial Bonding Properties of Dissimilar T-Lap Joints Using Friction Stir Welding Parameters
- 15 December 2022
- Published by Springer Nature
- p. 123-132
Prediction of Initial Crack Propagation Direction of Dissimilar Friction Stir Welded T-Joint
- 15 December 2022
- Published by Springer Nature
- p. 123-132
Prediction of Initial Crack Propagation Direction of Dissimilar Friction Stir Welded T-Joint
- 8 July 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (7-8) , 4677-4689
Pin length, pin offset, and reversed metal flow interaction in the improvement of dissimilar friction stir welded T-lap joints
- 8 July 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (7-8) , 4677-4689
Pin length, pin offset, and reversed metal flow interaction in the improvement of dissimilar friction stir welded T-lap joints
- 4 May 2022
- Published by Springer Nature
- p. 130-134
Effect of Friction Stir Welding Speeds on Interface Formation of Dissimilar T-joint Aluminum Alloys
- 4 May 2022
- Published by Springer Nature
- p. 130-134
Effect of Friction Stir Welding Speeds on Interface Formation of Dissimilar T-joint Aluminum Alloys