AGAnastasiia Grymak

Anastasiia Grymak

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anastasiia Grymak has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    LSTM-based prediction of wear in 3D-printed restorative materials under various methods

    by Anastasiia Grymak, Alexander Hui Xiang Yang, Kai Chun Li, Sunyoung Ma


  • pH prediction in commercial and experimental calcium silicate cements via material informatics

    by Clarice Ferreira Sabino, Anastasiia Grymak, Nikolaos Silikas, Vinicius Rosa


  • Open Access

    Evaluation of wear resistance and surface properties of additively manufactured restorative dental materials

    by Anastasiia Grymak, John M Aarts, Andrew B Cameron, Joanne Jung Eun Choi


  • Open Access

    Effect of Enamel Bleaching on the Bond Strength of Ceramic—A Systematic Review

    by Tsz Ho Seto, Anastasiia Grymak, Vidya Mudliar, Joanne Jung Eun Choi

    The increase in aesthetic demands has increased the use of ceramic dental restorations in dentistry. Ceramic restorations are bonded to the tooth structure using adhesives. There is a lack of standard guidelines in terms of post-bleaching time intervals and bond strengths of ceramic restorations. Bleaching products have also been stated to affect the morphology of enamel. Therefore, the purpose of this systematic review is to evaluate the bond strength between ceramic and enamel and the changes in the surface roughness of enamel post teeth bleaching. An electronic search was performed in the databases PubMed, OVID MEDLINE, Scopus, and Web of Science with MESH terms: “adhesion OR bonding”, “ceramic OR ceramics OR dental porcelain”, “tooth bleaching OR teeth bleaching OR tooth whitening OR teeth whitening” and “enamel OR dental enamel OR enamels OR dental enamels”. The articles were screened, and the final selection of articles was obtained by using the inclusion and exclusion criteria. Of the 170 studies identified from the search, only 12 studies met the inclusion criteria and were selected for full-text review. A further search by hand was performed, and additional 48 studies were selected. From the 60 full-text studies, 18 studies met the inclusion criteria and were included for data extraction. The results were based on a descriptive analysis of the effect on bond strength of ceramic to enamel after a bleaching protocol and the changes in the surface roughness of enamel post bleaching protocol. In conclusion, bleaching protocols alter the surface roughness of enamel and, thus, the shear bond strength between ceramic and enamel. Bleaching treatments with a higher concentration of hydrogen peroxide reduce the bond strength between ceramic and enamel. Delaying bonding after bleaching for up to 7 days increases the bond strength between ceramic and enamel.


  • Open Access

    Bond Strength between CAD/CAM PMMA Denture Base Resins and Characterisation Composites

    by Mei Ting Pong, Anastasiia Grymak, John Neil Waddell, Joanne Jung Eun Choi

    Aim: To measure the bond strength between two different CAD/CAM PMMA denture base resins and three different types of gum characterisation composites. Materials and Methods: CAD/CAM single cross-linked (Telio CAD) and double cross-linked (Vivodent CAD) resins were prepared, obtaining a total of 180 bar specimens. Each specimen was prepared according to the manufacturer’s instructions. The specimens were bonded to three different characterisation composites with varying viscosities; Kulzer Pala-creactive (P), Ivoclar SR Nexco (S), Shofu Ceramage (F). All the specimens were then tested using a chevron-notched three-point bond strength test in a universal testing machine to obtain fracture energy release toughness (MPa√m) and bond strength (MPa). The specimens were thermocycled to simulate 6 and 12 months of ageing in vivo. The results were statistically analysed (SPSS). The fractured surfaces of the tested specimens were examined with a scanning electron microscope (SEM) to evaluate the failure modes. Results: Pala-creactive characterisation composites showed the highest overall bond strength (3.49 ± 0.86 MPa) and fracture toughness (1.59 ± 0.34 MPa√m) when bonded to both CAD PMMA denture resins, which were statistically higher than the values obtained when they were bonded to Telio (p < 0.001). The Ceramage composite showed the lowest bond strength (1.05 ± 0.59 MPa) and fracture toughness (0.47 ± 0.4 MPa√m). The dominant mode of failure for all groups was mixed. Conclusion: Single cross-linked PMMA (Telio) showed a higher overall bond strength compared to double cross-linked PMMA when bonded to three different characterisation composites. Telio CAD showed a clear bond strength decrease after 6 and 12 months of artificial ageing, while Vivodent CAD showed a bond strength increase.


  • Wear Behavior of Occlusal Splint Materials Manufactured By Various Methods: A Systematic Review

    by Anastasiia Grymak, John M. Aarts, Sunyoung Ma, J. Neil Waddell, Joanne Jung Eun Choi

    Purpose : To systematically review studies on various materials and methods used for wear testing of occlusal devices and their antagonists in vitro and in vivo. Materials and Methods : An electronic search in OVID, Web of Science, PubMed and Scopus was conducted using the following terms (MeSH words) with any synonyms and closed terms: “Splint” OR “occlusal splint” OR “night guard” OR “occlusal device” OR “occlusal devices” OR deprogrammer OR “bite splint” OR “bite plane” OR “orthotic appliance” OR “orthotic devices” AND wear OR “two-body wear” OR “three-body wear” OR “tooth wear” OR “wear measurement” OR “wear behaviour” OR “wear behavior” OR abrasion AND “Polymethyl Methacrylate” OR PMMA OR “acrylic resin” OR dental material OR dental enamel OR CAD OR CAM OR PEEK OR “material testing”. Database search was limited to the English-language publications and published between 2001 and 1st of September 2021. A further hand search was done to ensure all materials were captured. Results : After the removal of duplicates, 115 studies were identified, and 11 were chosen for review. Studies showed that the lowest volumetric loss was observed in PEEK occlusal device materials, whereas heat-cure, CAD-milled and 3D printed occlusal device materials had no significant difference in wear. Vacuum-formed materials showed the highest wear among all groups. Testing parameters were found to be inconsistent across all studies. Conclusion : There is a need for standardization of in vitro and in vivo wear measurement and testing protocols as our study revealed a wide variety of testing protocols which potentially could influence the outcome. Polishing procedures are required for the material. Limited studies are available on 3D printed occlusal device materials and would therefore require further investigation, especially on printing build angles and settings. Further clinical studies would be advantageous to provide guidance on the selection of the best occlusal device material that would last the longest without remake. This article is protected by copyright. All rights reserved


  • Comparison of hardness and polishability of various occlusal splint materials

    by Anastasiia Grymak, John M. Aarts, Sunyoung Ma, John Neil Waddell, Joanne Jung Eun Choi