Yuguo Cui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuguo Cui has a total of 105 co-authors. Here are the top co-authors by number of shared publications:
- Yiling Yang
Ningbo University
11 shared publications - Gaohua Wu
Huzhou University
5 shared publications - Junqiang Lou
Key Laboratory of Micro-Nano Motion and Intelligent Control, School of Mechanical Engineering and Mechanics, Ningbo University, Ningbo, China
5 shared publications - Tehuan Chen
Key Laboratory of Micro-Nano Motion and Intelligent Control, School of Mechanical Engineering and Mechanics, Ningbo University, Ningbo, China
5 shared publications - Dan Liang
Ningbo Key Laboratory of Micro‐Nano Motion and Intelligent Control Ningbo University Ningbo People's Republic of China
3 shared publications Xingyang Xie
Faculty of Mechanical Engineering & Mechanics, Ningbo University, Ningbo, Zhejiang, 315211, China
3 shared publications
Latest Publications
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 31 (4) , 3897-3907
A Novel 2-stator Asynchronous Driven Piezoelectric Stick-Slip Stage With Wedge Mechanism
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 31 (4) , 3897-3907
A Novel 2-stator Asynchronous Driven Piezoelectric Stick-Slip Stage With Wedge Mechanism
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 31 (4) , 3863-3874
A Novel Symmetrical Opposite Linear Stick-Slip Actuator Using Macro Fiber Composite
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 31 (4) , 3863-3874
A Novel Symmetrical Opposite Linear Stick-Slip Actuator Using Macro Fiber Composite
- Open Access
Modeling, Comparative Investigation and Compensation for Hysteresis Response of Actuator Using Nonlinear Transformation
Aiming at problems such as the reduced positioning accuracy and insufficient dynamic response caused by the inherent hysteresis nonlinearity of piezoelectric actuators, this paper proposes a hysteresis modeling and compensation method for piezoelectric actuators based on nonlinear transformation. The proposed NT hysteresis model utilizes the nonlinear characteristics of activation functions to describe the complex nonlinearity in the hysteresis response of piezoelectric actuators. On this basis, a feedforward compensation controller is further designed based on the proposed inverse NT hysteresis model. Moreover, a composite controller is constructed by combining it with PID feedback to improve the dynamic response speed and trajectory tracking accuracy of piezoelectric actuators. Based on experimental data, the fitting performance of the proposed model is compared with that of several common hysteresis models using evaluation indicators including RMSE, MAPE and SMAPE. Finally, the performance of the proposed control method is verified through step response and sinusoidal trajectory tracking experiments. Experimental results show that the proposed NT hysteresis model performs best in characterizing the hysteresis characteristics of piezoelectric actuators, and the feedforward compensation controller constructed based on its inverse model exhibits superior control performance.
Open AccessModeling, Comparative Investigation and Compensation for Hysteresis Response of Actuator Using Nonlinear Transformation
Aiming at problems such as the reduced positioning accuracy and insufficient dynamic response caused by the inherent hysteresis nonlinearity of piezoelectric actuators, this paper proposes a hysteresis modeling and compensation method for piezoelectric actuators based on nonlinear transformation. The proposed NT hysteresis model utilizes the nonlinear characteristics of activation functions to describe the complex nonlinearity in the hysteresis response of piezoelectric actuators. On this basis, a feedforward compensation controller is further designed based on the proposed inverse NT hysteresis model. Moreover, a composite controller is constructed by combining it with PID feedback to improve the dynamic response speed and trajectory tracking accuracy of piezoelectric actuators. Based on experimental data, the fitting performance of the proposed model is compared with that of several common hysteresis models using evaluation indicators including RMSE, MAPE and SMAPE. Finally, the performance of the proposed control method is verified through step response and sinusoidal trajectory tracking experiments. Experimental results show that the proposed NT hysteresis model performs best in characterizing the hysteresis characteristics of piezoelectric actuators, and the feedforward compensation controller constructed based on its inverse model exhibits superior control performance.
- 2 April 2026
- Published by Elsevier in Precision Engineering
- Vol. 100, 636-652
Precision measurement of step-style microstructure based on differential confocal with suppression of non-uniform reflectivity and edge effect
- 2 April 2026
- Published by Elsevier in Precision Engineering
- Vol. 100, 636-652
Precision measurement of step-style microstructure based on differential confocal with suppression of non-uniform reflectivity and edge effect
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (8) , 12215-12227
Iterative Learning Model Predictive Control of Underwater Flexible Structure With Harmonic Actuation by Macrofiber Composites
The precise trajectory tracking of underwater flexible structures driven by smart materials is essential for bionic underwater propulsion systems, thus attracting increasing attention. In this work, we introduce a compound controller that combines an iterative learning model predictive control (ILMPC) with a dynamic hysteresis compensator. This approach realizes effective trajectory tracking of an underwater flexible structure through harmonic actuation of macrofiber composites (MFC) across a relatively broad frequency range. We present a dynamic hysteresis model that includes a state space model and a modified Prandtl–Ishlinskii (MPI) model. Experimental results indicate that the proposed hysteresis model effectively captures the underwater dynamic hysteresis nonlinearity of the MFC-actuated structure. Then, we develop the ILMPC method, which integrates model predictive control and iterative learning to reject real-time hydrodynamic disturbances and model uncertainties. To generate effective input trajectories, we design a generalized objective function that allows for independent adjustment of the weighting factors for manipulated variables to time indexes and interactive predictive horizons. We also discuss the convergence and robustness of the ILMPC. Experiments demonstrate the effectiveness of the proposed compound controller over a broad frequency range. These findings are meaningful for MFC-actuated flexible structures in applications of autonomous underwater vehicles, robotic fish, and other applications.
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (8) , 12215-12227
Iterative Learning Model Predictive Control of Underwater Flexible Structure With Harmonic Actuation by Macrofiber Composites
The precise trajectory tracking of underwater flexible structures driven by smart materials is essential for bionic underwater propulsion systems, thus attracting increasing attention. In this work, we introduce a compound controller that combines an iterative learning model predictive control (ILMPC) with a dynamic hysteresis compensator. This approach realizes effective trajectory tracking of an underwater flexible structure through harmonic actuation of macrofiber composites (MFC) across a relatively broad frequency range. We present a dynamic hysteresis model that includes a state space model and a modified Prandtl–Ishlinskii (MPI) model. Experimental results indicate that the proposed hysteresis model effectively captures the underwater dynamic hysteresis nonlinearity of the MFC-actuated structure. Then, we develop the ILMPC method, which integrates model predictive control and iterative learning to reject real-time hydrodynamic disturbances and model uncertainties. To generate effective input trajectories, we design a generalized objective function that allows for independent adjustment of the weighting factors for manipulated variables to time indexes and interactive predictive horizons. We also discuss the convergence and robustness of the ILMPC. Experiments demonstrate the effectiveness of the proposed compound controller over a broad frequency range. These findings are meaningful for MFC-actuated flexible structures in applications of autonomous underwater vehicles, robotic fish, and other applications.
- Open Access
- 1 March 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3204 (1)
Structural design and analysis of piezoelectric objective lens actuator
To address the limited output stroke of piezoelectric stacks, a double parallel four-bar displacement amplification mechanism is designed. The statics and dynamics of the mechanism are simulated using ANSYS software, and the motion amplification ratio and natural frequency of the mechanism are analyzed. The output displacement can reach 87 μm, the first-order natural frequency reaches 394 Hz, the maximum stress is 92 Mpa, and the parasitic displacement is almost non-existent due to the double parallel four-bar mechanism, which meets the actual needs and provides some theoretical guidance for the realization of large-range displacement output of piezoelectric objective lens drivers.
- 1 March 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3204 (1)
Open AccessStructural design and analysis of piezoelectric objective lens actuator
To address the limited output stroke of piezoelectric stacks, a double parallel four-bar displacement amplification mechanism is designed. The statics and dynamics of the mechanism are simulated using ANSYS software, and the motion amplification ratio and natural frequency of the mechanism are analyzed. The output displacement can reach 87 μm, the first-order natural frequency reaches 394 Hz, the maximum stress is 92 Mpa, and the parasitic displacement is almost non-existent due to the double parallel four-bar mechanism, which meets the actual needs and provides some theoretical guidance for the realization of large-range displacement output of piezoelectric objective lens drivers.
- 15 January 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (1)
Dual-layer sliding mode motion control of piezoelectric stick-slip actuator based on nonlinear extended state observer
In this article, a dual-layer sliding mode control scheme based on a nonlinear extended state observer (NESO) is designed to achieve displacement tracking of the piezoelectric stick-slip actuator (PSSA). A simple and continuous friction model (SCFM) is constructed based on the Coulomb friction model and the hyperbolic tangent function, and the electromechanical-rigid-flexible-friction coupled dynamics of the PSSA is established. By introducing a tracking differentiator (TD), the overshoot that adversely affects displacement control is effectively suppressed, while the unknown nonlinear characteristics of the PSSA are actively estimated through the NESO. The convergence speed and control accuracy of the PSSA are enhanced by the designed dual-layer sliding mode controller, and the stability of both the NESO and the controller is analyzed using the Lyapunov method and finite-time control theory. Finally, experimental results on motion control demonstrate that the proposed dual-layer sliding mode approach effectively achieves the desired positioning and trajectory tracking performance of the PSSA.
- 15 January 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (1)
Dual-layer sliding mode motion control of piezoelectric stick-slip actuator based on nonlinear extended state observer
In this article, a dual-layer sliding mode control scheme based on a nonlinear extended state observer (NESO) is designed to achieve displacement tracking of the piezoelectric stick-slip actuator (PSSA). A simple and continuous friction model (SCFM) is constructed based on the Coulomb friction model and the hyperbolic tangent function, and the electromechanical-rigid-flexible-friction coupled dynamics of the PSSA is established. By introducing a tracking differentiator (TD), the overshoot that adversely affects displacement control is effectively suppressed, while the unknown nonlinear characteristics of the PSSA are actively estimated through the NESO. The convergence speed and control accuracy of the PSSA are enhanced by the designed dual-layer sliding mode controller, and the stability of both the NESO and the controller is analyzed using the Lyapunov method and finite-time control theory. Finally, experimental results on motion control demonstrate that the proposed dual-layer sliding mode approach effectively achieves the desired positioning and trajectory tracking performance of the PSSA.
- 1 January 2026
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 62 (4) , 75-85
Research on Precision Self-sensing Method for Displacement and Force of Piezoelectric Actuator
- 1 January 2026
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 62 (4) , 75-85
Research on Precision Self-sensing Method for Displacement and Force of Piezoelectric Actuator
- 11 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Automation Science and Engineering
- Vol. 22 (15455955) , 18560-18569
Real-Time Trajectory Tracking of a Piezoelectric Microrobot Using Asynchronous Fusion of Vision Cameras and Laser Sensors
This study developed a multisensor asynchronous fusion method for vision cameras and laser sensors for real-time tracking of a millimeter-scale piezoelectric microrobot with high sampling rates. The design, manufacture, and realization of the proposed microrobot using a monolithic integrated manufacturing process is realized with a size of 36×36×18 mm and a weight of 4.9 g. Two local estimators for the vision camera and laser sensors are established independently for 2-D tracking of the millimeter-scale microrobot. An asynchronous fusion method for the camera and laser sensors is developed by optimally weighting the two local estimators in a linear minimum variance framework using the Lagrange multiplier method at the synchronized update time. High-precision 2-D trajectory tracking of the proposed microrobot was achieved with an average velocity of 301.6 mm/s and a sampling rate of up to 4000 Hz. Experiments tracking different trajectories of the microrobot at different velocities and sampling rates demonstrated the effectiveness of the proposed fusion method.
- 11 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Automation Science and Engineering
- Vol. 22 (15455955) , 18560-18569
Real-Time Trajectory Tracking of a Piezoelectric Microrobot Using Asynchronous Fusion of Vision Cameras and Laser Sensors
This study developed a multisensor asynchronous fusion method for vision cameras and laser sensors for real-time tracking of a millimeter-scale piezoelectric microrobot with high sampling rates. The design, manufacture, and realization of the proposed microrobot using a monolithic integrated manufacturing process is realized with a size of 36×36×18 mm and a weight of 4.9 g. Two local estimators for the vision camera and laser sensors are established independently for 2-D tracking of the millimeter-scale microrobot. An asynchronous fusion method for the camera and laser sensors is developed by optimally weighting the two local estimators in a linear minimum variance framework using the Lagrange multiplier method at the synchronized update time. High-precision 2-D trajectory tracking of the proposed microrobot was achieved with an average velocity of 301.6 mm/s and a sampling rate of up to 4000 Hz. Experiments tracking different trajectories of the microrobot at different velocities and sampling rates demonstrated the effectiveness of the proposed fusion method.