Mohammad Aatif Qazi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Aatif Qazi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Mohsin
Mechanical Engineering Department, Jamia Millia Islamia, New Delhi, India
2 shared publications Mohammad Faizan
Mechanical Engineering Department, Aligarh Muslim University, Aligarh, UP, India
1 shared publication- Mohd Bilal Naim Shaikh
Department of Mechanical Engineering, Aligarh Muslim University, Aligarh, India
1 shared publication Mohd Misbah
Department of Mechanical Engineering, AMU, Aligarh, UP, India
1 shared publicationMohd. Suhaib
Department of Mechanical Engineering, JMI, New Delhi, India
1 shared publication
Latest Publications
- 1 September 2021
- Published by IOP Publishing in Engineering Research Express
- Vol. 3 (3) , 035036
Experimental and modeling studies on dry sliding wear behavior of Alumina reinforced AMC
In the present research work predicted properties of Aluminium Alloy Composites prepared through powder metallurgy technique have been examined using Artificial Neural Network (ANN) approach. The aluminium alloy (Al-20Fe −5Cr) matrix reinforced with aluminium oxide (Al 2 O 3 ) varying from 0–30 wt% with a step of 10 wt% were prepared. The green compacts prepared at three different compaction pressures viz. 470, 550 and 600 MPa were sintered at 440 °C for 30 min. Pin-on-disc test was performed to evaluate wear loss of the composites prepared. The influence of alumina varying weight percentage and different compaction pressure had been analyzed and tests were performed according to full factorial design. Analysis of variance (ANOVA) had been employed to predict the percentage contribution of various process parameters. The results indicated that the wear loss was mainly influenced by alumina percentage followed by compaction pressure by 92% and 8% respectively. For modeling and prediction of wear loss, a feed forward back propagation neural network was constructed and compared with experimentally calculated values. Both experimental and ANN predicted values of wear loss were in close correlation with each other with approximately (1–3) % error.
- 1 September 2021
- Published by IOP Publishing in Engineering Research Express
- Vol. 3 (3) , 035036
Experimental and modeling studies on dry sliding wear behavior of Alumina reinforced AMC
In the present research work predicted properties of Aluminium Alloy Composites prepared through powder metallurgy technique have been examined using Artificial Neural Network (ANN) approach. The aluminium alloy (Al-20Fe −5Cr) matrix reinforced with aluminium oxide (Al 2 O 3 ) varying from 0–30 wt% with a step of 10 wt% were prepared. The green compacts prepared at three different compaction pressures viz. 470, 550 and 600 MPa were sintered at 440 °C for 30 min. Pin-on-disc test was performed to evaluate wear loss of the composites prepared. The influence of alumina varying weight percentage and different compaction pressure had been analyzed and tests were performed according to full factorial design. Analysis of variance (ANOVA) had been employed to predict the percentage contribution of various process parameters. The results indicated that the wear loss was mainly influenced by alumina percentage followed by compaction pressure by 92% and 8% respectively. For modeling and prediction of wear loss, a feed forward back propagation neural network was constructed and compared with experimentally calculated values. Both experimental and ANN predicted values of wear loss were in close correlation with each other with approximately (1–3) % error.
- 2 January 2021
- Published by IOP Publishing in Engineering Research Express
- Vol. 3 (1) , 015002
Analysis and prediction of the tensile strength of aluminum alloy composite using statistical and artificial neural network technique
- 2 January 2021
- Published by IOP Publishing in Engineering Research Express
- Vol. 3 (1) , 015002
Analysis and prediction of the tensile strength of aluminum alloy composite using statistical and artificial neural network technique