Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Liqing Sun has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Study on the transient flow field evolution and mixing characteristics of a fluidic oscillator under ultrasonic excitation

    by Liqing Sun, Suyang Li, Shenghao Ma, Kuidong Gao, Lin Li

    To enhance reagent dispersion in high-viscosity systems, this study employs computational fluid dynamics simulations and high-speed photography to evaluate the transient flow and mixing characteristics of a fluidic oscillator mixer, comparing performance with and without ultrasonic excitation. The results indicated that ultrasonic intervention did not alter the inherent sweeping frequency but induced intensive alternating pressure pulsations. Quantitatively, over a 2.0 s period, the number of connected components (Ncc) exhibits a stepwise amplification with increasing ultrasonic intensity, confirming that high-frequency acoustic energy effectively shatters large-scale fluid structures to expand the mixing interfacial area. Concurrently, the introduction of ultrasound elevates the mean velocity but reduces the maximum velocity, revealing a stronger dependency on power over frequency, where higher power enhances internal momentum transport. Furthermore, the time-averaged volume-averaged turbulent kinetic energy and its corresponding dissipation rate under the ultrasonic condition are elevated by 45.6% and 10.2%, respectively. Quantitative image analysis confirmed that ultrasound significantly accelerates the initial mixing rate, reducing the concentration standard deviation at 0.23 s from 2.01 to 1.31. Throughout the subsequent evolution, ultrasound effectively suppresses localized concentration oscillations, steadily decreasing the final coefficient of variation of the flow field to approximately 0.14 to simultaneously enhance global mixing efficiency and homogeneity. This study offers useful fluid-dynamic insights for the design and optimization of ultrasound-assisted jet mixers.

  • Open Access

    Measurement and analysis of dynamic performance of shearer cutting part transmission system under different working conditions using simulation method

    by Kuidong Gao, Zhiteng Liu, Guanzhan Dong, Xiaodi Zhang, Liqing Sun, Shengru Zhang, Tianyu Liu

    As key coal mining equipment, the shearer is crucial for improving adaptability to complex conditions, extending service life, and reducing failure rates—key to enhancing coal production economic benefits. Using the transmission system model, dynamic bearing contact forces, vibration acceleration at virtual measurement points, and vibration levels in gangue/pure coal conditions are analyzed. The reliability and accuracy of the finite element analysis for the cutting unit's vibration characteristics were validated via bench test comparison. The vibration-data-equipped housing is input into acoustic boundary element simulation; combined with the built model, noise variations at different sound field response points with gear face width and bottom clearance coefficient are derived. Results show high-order modal analysis confirms no system resonance risk. When the motor gear face width is 74mm, planetary gear train face width 140mm, and bottom clearance coefficient 0.4, the gears exhibit excellent load-bearing capacity, stability, and low vibration/noise.

  • High-precision pose measurement of hydraulic supports using LiDAR-binocular camera with cooperative target detection

    by Kuidong Gao, Tianhao Yuan, Sheng Chen, Xiaodi Zhang, Liqing Sun

    During fully mechanized coal mining, hydraulic supports are prone to posture variations such as pitching, tilting, and twisting, which directly impact their support performance, coordination with shearers, and the overall operational stability of the working face. Existing posture detection methods often exhibit limitations in positioning accuracy, long-term stability, and hardware complexity. To address these challenges, this paper proposes an integrated LiDAR-binocular camera detection system. By quantifying the effects of target surface material, distance, angle, and environmental factors on LiDAR performance, a robust target recognition model is developed. Integrating this with binocular distortion correction, image segmentation, and circle detection algorithms, high-precision target localization and posture estimation are achieved. Finally, static and dynamic accuracy tests were conducted on a hydraulic support experimental platform using the MARS motion capture system. The results demonstrate that the proposed method effectively meets the requirements for hydraulic support posture detection in the complex environment of fully mechanized mining faces.

  • Open Access

    Investigation of Flotation Bubbles Movement Behavior under the Influence of an Immersed Ultrasonic Vibration Plate

    by Kuidong Gao, Wenchao Zong, Zhihua Zhang, Liqing Sun, Lin Li

    Ultrasonic flotation is widely used as an efficient mineral separation method. Its efficiency is related to the adhesion behavior between fine particles and flotation bubbles, which can be influenced by the bubbles’ movement behavior. This paper used two immersed ultrasonic vibration plates to generate ultrasonic action and investigated the effect of ultrasonic action on the rising process of flotation bubbles. The distribution, aggregation and fusion, velocity, and other characteristics of bubbles generated by different needle apertures were studied by experimental and simulation methods. The results showed that a 0.4 mm needle produced bubbles that were more evenly spaced and more uniform in size and shape. The ultrasonic action can make the bubbles aggregate together and reduce the bubble rise velocity, as well as prolong their time in the flotation process at the same time. It is beneficial to the sufficient collision and adhesion behavior between flotation bubbles and particles, eventually improving the efficiency of mineral flotation.


  • Open Access

    Abrasivity database of different genetic rocks based on CERCHAR Abrasivity Test

    by Kuidong Gao, Xinyu Wang, Hongxin Wei, Shuxue Wang, Weipeng Xu, Xu Li, Liqing Sun, Hongxiang Jiang

    Rock abrasivity is one of the main factors affecting the wear of rock-cutting tools, which is usually quantified by the CERCHAR Abrasivity Index (CAI). Researchers and engineers study tool wear and predict tool life based on the CAI of rocks. However, there is still a lack of a dataset on rock properties, especially the abrasivity of various rocks. This paper reports the abrasive dataset of 10 kinds of rocks, including sedimentary rocks, metamorphic rocks, and igneous rocks, with the aid of the CERCHAR Abrasivity Test and digital measurement techniques. The dataset comprises rock abrasivity data, point cloud data for visualization, scratch photos, CERCHAR Abrasivity Test force data, and mechanical properties (uniaxial compressive strength) of rock samples. This dataset facilitates future research on rock abrasivity and rock-cutting tool wear.


  • Open Access

    Effect of Gas Input Conditions and Ultrasound on the Dynamic Behavior of Flotation Bubbles

    by Kuidong Gao, Hong Liu, Liqing Sun, Zhihua Zhang

    Ultrasonic flotation is useful for fine low-rank coal purification; however, the efficiency of ultrasonic flotation still needs to be improved. Because the dynamic behavior of flotation bubbles has significant effects on their flotation efficiency, it was investigated under different gas input conditions with and without ultrasound using the volume of fluid method and h-speed imaging. The results indicated that the gas input method can influence the final kinetic behavior of the flotation bubbles by changing the morphology of the initial bubble. With an increase in the size and aspect ratio of the bubble, the bubble deformation and velocity increased, and the range of motion of the bubble increased and then decreased. Meanwhile, the size of the bubble increased with an increase in the thickness of the vibrating plate of the ultrasonic transducer owing to the aggregation of the bubbles under the influence of ultrasound.


  • Open Access

    Drilling study of bit in gravel environment based on DEM–MBD

    by Kuidong Gao, Jihai Liu, Tianjiao Wu, Qingliang Zeng, Liqing Sun, Xiaodi Zhang

    In the process of rock bolt support for the roadway with floor heave, the rock bolt cannot reach the bottom of the borehole smoothly due to the influence of the collapse gravels around the borehole. In order to solve the problem of difficult rock bolt installation, the auxiliary installation device of rock bolt drilling was innovatively designed. At the same time, a new method of auxiliary bolt installation was put forward, in which a bit was installed at the bottom of the bolt to assist the bolt drilling. The drilling process of the bit was simulated by the co‐simulation of discrete element method (DEM) and multibody dynamics method (MBD). The axial resistance of the bit and the change law of the particles movement were studied under different motion parameters and structural parameters. It was found that the drilling performance of bit was directly related to the motion parameters and structure of bit. And the selection of gravel parameters in DEM was verified by experiments. The research results can provide technical guidance for bit structure design and the selection of motion parameters of bolt drilling auxiliary installation device, and can effectively improve the rock bolt installation efficiency.


  • Open Access

    Adsorption Characteristics and Mechanism of Calcium Ions on Different Molybdenite Surfaces via Experiments and DFT Simulations

    by Liqing Sun, Yijun Cao, Lin Li, Qingliang Zeng

    Calcium ions are common in flotation process water, and have a significant effect on the molybdenite floatability, making separation of molybdenite from other minerals more difficult. Therefore, to improve the separation selectivity, the research of how calcium ions affect the molybdenite surface properties is of great significance. In this study, various methods including flotation tests, contact angle measurements, batch adsorption tests and Density Functional Theory (DFT) simulations were carried out to understand the adsorption characteristics and mechanism. Results of the contact angle measurements showed that the inhibition effects of calcium ions on molybdenite flotation kinetics were mostly attributed to the decrease of the edge surface hydrophobicity, as the contact angle of the edge surface decreased more than the face surface after treatment with calcium ions. While fitting the results of batch adsorption tests with adsorption kinetics and isotherm models, it was found that the Lagergen pseudo-first-order equation and the Freundlich isotherm model nicely follow the experimental trend. Moreover, DFT calculation results indicated that both Ca2+ and CaOH+ preferentially adsorb on the molybdenite (100) surface, particularly the edge surface, which was consistent with the contact angle results. Ca2+ adsorbed on the Mo-top site on the S-(100) surface by forming Ca-S bonds, transferring electrons from Ca 3d orbitals to S 3p orbitals. CaOH+ adsorbed on the S-top site of Mo-(100) surface by forming a strong covalent Mo-O bond and S-Ca bond. The results provide a basis for understanding and improving the separation effect of molybdenite from other minerals in the presence of calcium ions.


  • Open Access

    Relative Position and Posture Detection of Hydraulic Support Based on Particle Swarm Optimization

    by Kuidong Gao, Wenbo Xu, Hongyang Zhang, Yi Zhang, Qingliang Zeng, Liqing Sun

    The position and posture of the hydraulic support seriously affect the efficiency of coal mining and the safety of coal production. However, most of the current detection technologies have poor reliability, and the detection methods are difficult to adapt to the complex environment of coal mines. To effectively monitor the hydraulic support, and thereby improve the efficiency of coal mining, we propose a new method to detect the relative position and posture of the hydraulic support. The method is based on the mathematical idea that three points can determine a plane. Firstly, we use angle sensors and displacement sensors to build the detection device, use STM32 microprocessor to collect data, and realize real-time display of the data on the PC. Then, we conduct a single point detection experiment and a plane moving experiment, and combined the particle swarm optimization (PSO) algorithm to optimize the data. Experiment results show that the relative error of the single-point detection can reach 0.53%. Thirdly, we carry out a detection experiment of three points on the plane. Experiment results show that the detection accuracy of the two planes can reach 0.2°. Finally, to test the monitoring effect of the detection device on the hydraulic support, we carry out the relative position and posture detection experiment of the canopy. The experiment results show that the device can effectively detect the posture change of the canopy when the hydraulic support are moving. The method we use is contact measurement, which has high reliability and strong stability. The research on the relative position and posture detection of hydraulic support provides a reliable method to monitor the support working status. It lays the foundation for the intelligent control of the mining working face straightness and the perception of the support posture.