Jiarui Gong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jiarui Gong has a total of 230 co-authors. Here are the top co-authors by number of shared publications:
- Zhenqiang Ma
Department of Electrical and Computer Engineering University of Wisconsin‐Madison Madison Wisconsin USA
27 shared publications - Jie Zhou
Department of Electrical and Computer Engineering University of Wisconsin‐Madison Madison Wisconsin USA
22 shared publications - Boon S. Ooi
King Abdullah University of Science and Technology (KAUST)
12 shared publications - Tien Khee Ng
King Abdullah University of Science and Technology (KAUST)
11 shared publications - Yang Liu
Department of Electrical and Computer Engineering, University of Wisconsin-Madison 1 , Madison, Wisconsin 53706
10 shared publications - Yi Lu
Department of Electrical and Computer Engineering, University of Wisconsin-Madison 1 , Madison, Wisconsin 53706
10 shared publications
Latest Publications
- Open Access
- 15 September 2026
- Published by Wiley in Advanced Materials Interfaces
- Vol. 13 (20)
Band Alignment of Grafted Si/Ge 0.89 Sn 0.11 Heterojunction Determined by X‐Ray Photoelectron Spectroscopy
We investigate the band alignment of a monocrystalline grafted p‐type Si/Ge 0.89 Sn 0.11 heterostructure using X‐ray photoelectron spectroscopy (XPS). The bandgap of the Ge 0.89 Sn 0.11 epilayer of 0.50 eV was first determined and cross‐verified using photoluminescence spectroscopy, infrared transmission, and theoretical calculation. The band offsets values at the grafted Si/Ge 0.89 Sn 0.11 interface were determined using Kraut's method via a top‐down interface approach with multiple core‐level combinations, yielding a valence band offset (VBO) of −0.43 ± 0.031 eV and a conduction band offset (CBO) of +0.19 eV. The band alignment was also constructed based on Anderson's rule by using work function values extracted from secondary electron cutoff (SECO) measurements. The effective band alignment extracted from Kraut's method shows good agreement with the Anderson‐rule estimate, suggesting that interface‐state‐induced Fermi‐level pinning is not dominant in the grafted Si/Ge 0.89 Sn 0.11 heterostructure. This buffer‐free, oxide‐mediated grafted interface offers a promising integration strategy for high‐Sn‐content GeSn directly on Si for future optoelectronic applications.
- 15 September 2026
- Published by Wiley in Advanced Materials Interfaces
- Vol. 13 (20)
Open AccessBand Alignment of Grafted Si/Ge 0.89 Sn 0.11 Heterojunction Determined by X‐Ray Photoelectron Spectroscopy
We investigate the band alignment of a monocrystalline grafted p‐type Si/Ge 0.89 Sn 0.11 heterostructure using X‐ray photoelectron spectroscopy (XPS). The bandgap of the Ge 0.89 Sn 0.11 epilayer of 0.50 eV was first determined and cross‐verified using photoluminescence spectroscopy, infrared transmission, and theoretical calculation. The band offsets values at the grafted Si/Ge 0.89 Sn 0.11 interface were determined using Kraut's method via a top‐down interface approach with multiple core‐level combinations, yielding a valence band offset (VBO) of −0.43 ± 0.031 eV and a conduction band offset (CBO) of +0.19 eV. The band alignment was also constructed based on Anderson's rule by using work function values extracted from secondary electron cutoff (SECO) measurements. The effective band alignment extracted from Kraut's method shows good agreement with the Anderson‐rule estimate, suggesting that interface‐state‐induced Fermi‐level pinning is not dominant in the grafted Si/Ge 0.89 Sn 0.11 heterostructure. This buffer‐free, oxide‐mediated grafted interface offers a promising integration strategy for high‐Sn‐content GeSn directly on Si for future optoelectronic applications.
- 16 June 2026
- Published by Springer Nature in Nature Electronics
- Vol. 9 (8) , 941-955
A wirelessly powered, light-controlled, bioresorbable stimulation system with programmable polyphasic waveforms
- 16 June 2026
- Published by Springer Nature in Nature Electronics
- Vol. 9 (8) , 941-955
A wirelessly powered, light-controlled, bioresorbable stimulation system with programmable polyphasic waveforms
- Open Access
- 25 April 2026
- Published by Wiley in Advanced Optical Materials
- Vol. 14 (19)
Optoelectronically Active GaAs/GeSn‐MQW/Ge Heterojunctions Created via Semiconductor Grafting
Semiconductor devices have traditionally relied on lattice‐matched heterojunctions formed via epitaxy. However, expanding device functionalities increasingly demands integration across extreme lattice mismatches. Here, a lattice‐mismatched, single‐crystalline GaAs/GeSn‐multi‐quantum well (MQW)/Ge n‐i‐p heterojunction photodiode is realized through advanced “semiconductor grafting” technology. This method enables simultaneous engineering of band alignment and optical field distribution. Comprehensive STEM characterization reveals an atomically clean GaAs/GeSn‐MQW interface with no observable interdiffusion. The resulting photodiode exhibits outstanding performance: a record‐low dark current density of 1.22 × 10 −7 A/cm 2 , extended spectral response from ∼0.5 to 2 µm, and high photo responsivities of 0.85 A/W and 0.40 A/W at 520 nm (VIS) and 1570 nm (NIR), respectively. Compared to epitaxial reference device, this represents a reduction in dark current by over five orders of magnitude, and responsivity enhancements of ∼7× in the VIS and ∼3× in the NIR ranges. This work establishes a new strategy for constructing lattice‐mismatched optoelectronic heterojunctions. Beyond the GaAs/GeSn‐MQW/Ge system, the approach offers a broadly applicable platform for high‐performance device integration free from conventional strict lattice‐matching requirement.
- 25 April 2026
- Published by Wiley in Advanced Optical Materials
- Vol. 14 (19)
Open AccessOptoelectronically Active GaAs/GeSn‐MQW/Ge Heterojunctions Created via Semiconductor Grafting
Semiconductor devices have traditionally relied on lattice‐matched heterojunctions formed via epitaxy. However, expanding device functionalities increasingly demands integration across extreme lattice mismatches. Here, a lattice‐mismatched, single‐crystalline GaAs/GeSn‐multi‐quantum well (MQW)/Ge n‐i‐p heterojunction photodiode is realized through advanced “semiconductor grafting” technology. This method enables simultaneous engineering of band alignment and optical field distribution. Comprehensive STEM characterization reveals an atomically clean GaAs/GeSn‐MQW interface with no observable interdiffusion. The resulting photodiode exhibits outstanding performance: a record‐low dark current density of 1.22 × 10 −7 A/cm 2 , extended spectral response from ∼0.5 to 2 µm, and high photo responsivities of 0.85 A/W and 0.40 A/W at 520 nm (VIS) and 1570 nm (NIR), respectively. Compared to epitaxial reference device, this represents a reduction in dark current by over five orders of magnitude, and responsivity enhancements of ∼7× in the VIS and ∼3× in the NIR ranges. This work establishes a new strategy for constructing lattice‐mismatched optoelectronic heterojunctions. Beyond the GaAs/GeSn‐MQW/Ge system, the approach offers a broadly applicable platform for high‐performance device integration free from conventional strict lattice‐matching requirement.
- 10 November 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (19)
Surface dipole formation and electronic structure evolution on β -Ga2O3
The surface electronic structure of Ga2O3 critically influences its metal/Ga2O3 contact and semiconductor/Ga2O3 interface property, as well as the overall device performance. However, the fundamental surface properties, e.g., band bending and vacuum bending are not yet fully understood, especially under surface treatment procedure. In this study, we systematically investigate the surface evolution of both (−201)- and (010)-oriented β-Ga2O3 using x-ray photoelectron spectroscopy in conjunction in situ Ar+ ion sputtering. Both surfaces initially exhibit significantly reduced work functions following widely unitized Piranha treatment, primarily due to the formation of inward-pointing surface dipoles arising from oxygen-rich terminations. As ion etching proceeds, the work function gradually increases and ultimately saturates once the dipole layer is fully removed. The Ga:O ratios and O 1s peak deconvolution indicates a gradual reduction in gallium hydroxyl (Ga-OH) groups, returning the surface toward stoichiometric composition. Quantitative analysis demonstrates that vacuum level bending (∼0.9 eV) far exceeds band bending (∼0.2 eV), highlighting a dipole-dominated mechanism. These findings provide crucial insights into the intricate interplay between surface chemistry and electronic structure, establishing a strategy for rational band alignment engineering via surface dipole control and optimizing interfaces in Ga2O3-based electronic and optoelectronics devices.
- 10 November 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (19)
Surface dipole formation and electronic structure evolution on β -Ga2O3
The surface electronic structure of Ga2O3 critically influences its metal/Ga2O3 contact and semiconductor/Ga2O3 interface property, as well as the overall device performance. However, the fundamental surface properties, e.g., band bending and vacuum bending are not yet fully understood, especially under surface treatment procedure. In this study, we systematically investigate the surface evolution of both (−201)- and (010)-oriented β-Ga2O3 using x-ray photoelectron spectroscopy in conjunction in situ Ar+ ion sputtering. Both surfaces initially exhibit significantly reduced work functions following widely unitized Piranha treatment, primarily due to the formation of inward-pointing surface dipoles arising from oxygen-rich terminations. As ion etching proceeds, the work function gradually increases and ultimately saturates once the dipole layer is fully removed. The Ga:O ratios and O 1s peak deconvolution indicates a gradual reduction in gallium hydroxyl (Ga-OH) groups, returning the surface toward stoichiometric composition. Quantitative analysis demonstrates that vacuum level bending (∼0.9 eV) far exceeds band bending (∼0.2 eV), highlighting a dipole-dominated mechanism. These findings provide crucial insights into the intricate interplay between surface chemistry and electronic structure, establishing a strategy for rational band alignment engineering via surface dipole control and optimizing interfaces in Ga2O3-based electronic and optoelectronics devices.
- 27 October 2025
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 7 (21) , 9700-9709
Band Alignment and Leakage Mechanism Analysis of p-Si/n-AlN Heterojunction Diodes with the Al 2 O 3 Interlayer
- 27 October 2025
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 7 (21) , 9700-9709
Band Alignment and Leakage Mechanism Analysis of p-Si/n-AlN Heterojunction Diodes with the Al 2 O 3 Interlayer
- Open Access
- 24 October 2025
- Published by AIP Publishing in APL Electronic Devices
- Vol. 1 (4)
Demonstration of AlGaAs/GeSn p-i-n diodes
This study reports the fabrication and characterization of an Al0.3Ga0.7As/Ge0.853Sn0.147/GeSn p-i-n double heterostructure (DHS) diode using a grafting approach for advanced optoelectronic applications, building upon prior work on the band alignment of this heterostructure. Compared to a reference Si0.03Ge0.89Sn0.08/Ge0.853Sn0.147/GeSn DHS diode fabricated using the same process, the grafted Al0.3Ga0.7As/Ge0.853Sn0.147/GeSn diodes exhibit a significantly reduced reverse leakage current (6.90 × 10−5 A/cm2 at −2 V), corresponding to an average on/off ratio of 2.95 × 103 across 326 devices. This performance enhancement is attributed to improved hole-blocking by the p-type AlGaAs cap layer, which suppresses reverse leakage and enhances rectification. Capacitance–voltage measurements reveal an interface trap density for the double heterojunction in the range of 0.86–5.4 × 1012/cm2 eV. These results establish the AlGaAs/GeSn DHS as a promising platform for next-generation electrically pumped GeSn lasers, potentially operable at elevated temperatures, and highlight its potential for advancing GeSn-based optoelectronic technologies for on-chip integration.
- 24 October 2025
- Published by AIP Publishing in APL Electronic Devices
- Vol. 1 (4)
Open AccessDemonstration of AlGaAs/GeSn p-i-n diodes
This study reports the fabrication and characterization of an Al0.3Ga0.7As/Ge0.853Sn0.147/GeSn p-i-n double heterostructure (DHS) diode using a grafting approach for advanced optoelectronic applications, building upon prior work on the band alignment of this heterostructure. Compared to a reference Si0.03Ge0.89Sn0.08/Ge0.853Sn0.147/GeSn DHS diode fabricated using the same process, the grafted Al0.3Ga0.7As/Ge0.853Sn0.147/GeSn diodes exhibit a significantly reduced reverse leakage current (6.90 × 10−5 A/cm2 at −2 V), corresponding to an average on/off ratio of 2.95 × 103 across 326 devices. This performance enhancement is attributed to improved hole-blocking by the p-type AlGaAs cap layer, which suppresses reverse leakage and enhances rectification. Capacitance–voltage measurements reveal an interface trap density for the double heterojunction in the range of 0.86–5.4 × 1012/cm2 eV. These results establish the AlGaAs/GeSn DHS as a promising platform for next-generation electrically pumped GeSn lasers, potentially operable at elevated temperatures, and highlight its potential for advancing GeSn-based optoelectronic technologies for on-chip integration.
- 26 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (11) , 2161-2164
Grafted GaAs/Si Heterojunction Tunnel Diodes With Improved Peak-to-Valley Current Ratio (PVCR) of up to 36.38
We report the fabrication and characteristics of GaAs/Si p+/n+ heterojunction tunnel diodes. These diodes were fabricated via grafting the freestanding single-crystalline p-type degenerately doped GaAs (4×1019 cm-3) nanomembrane (NM) onto single-crystalline n-type Si (5×1019 cm-3) substrate. At the heterointerface, an amorphous ultrathin oxygen-enriched layer (UOL) was intentionally engineered through chemical oxidation and atomic layer deposition (ALD). Scanning transmission electron microscopy (STEM) confirmed the formation of the UOL and the single crystallinity of the grafted junction. The resulting tunnel diodes consistently exhibited negative differential resistance (NDR) behavior at room temperature, with a high maximum peak-to-valley current ratio (PVCR) of 36.38, valley voltages ranging from 1.3 to 1.8 V, and a peak tunneling current density of 0.95 kA/cm2. This study not only highlights the critical roles of the UOL as both an interface improvement layer and a quantum tunneling medium, but also establishes "semiconductor grafting" as an effective and versatile method for high-performance, lattice-mismatched heterojunction devices.
- 26 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (11) , 2161-2164
Grafted GaAs/Si Heterojunction Tunnel Diodes With Improved Peak-to-Valley Current Ratio (PVCR) of up to 36.38
We report the fabrication and characteristics of GaAs/Si p+/n+ heterojunction tunnel diodes. These diodes were fabricated via grafting the freestanding single-crystalline p-type degenerately doped GaAs (4×1019 cm-3) nanomembrane (NM) onto single-crystalline n-type Si (5×1019 cm-3) substrate. At the heterointerface, an amorphous ultrathin oxygen-enriched layer (UOL) was intentionally engineered through chemical oxidation and atomic layer deposition (ALD). Scanning transmission electron microscopy (STEM) confirmed the formation of the UOL and the single crystallinity of the grafted junction. The resulting tunnel diodes consistently exhibited negative differential resistance (NDR) behavior at room temperature, with a high maximum peak-to-valley current ratio (PVCR) of 36.38, valley voltages ranging from 1.3 to 1.8 V, and a peak tunneling current density of 0.95 kA/cm2. This study not only highlights the critical roles of the UOL as both an interface improvement layer and a quantum tunneling medium, but also establishes "semiconductor grafting" as an effective and versatile method for high-performance, lattice-mismatched heterojunction devices.
- Open Access
- 1 June 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (6)
Defect-modulation in α-Ga2O3 molecular beam epitaxial photodetector investigated through pulsed-light persistent-photoconductivity
α-phase gallium oxide (Ga2O3) features a corundum crystal structure that closely matches the low-cost sapphire substrate commonly used in epitaxy, enabling researchers to perform precise and controllable Ga2O3 epitaxy. It thus offers an excellent material platform for the development of high-power devices and deep ultraviolet photodetectors (DUV-PDs). In this study, we altered the epitaxy properties of α-Ga2O3 grown on m-plane sapphire substrates by changing the growth parameters of oxide molecular beam epitaxy and demonstrated effective modulation of the oxygen vacancy (VO) dependent persistent photoconductivity (PPC) behavior. This gave rise to a tunable paired-pulse facilitation (PPF) index in the fabricated α-Ga2O3-based DUV-PDs. Using α-Ga2O3 grown on bare m-plane sapphire at 500 °C as a benchmark (α-Ga2O3-500 °C), we effectively altered the VO contribution by either increasing the growth temperature to 570 °C or introducing a step-graded α-(AlxGa1−x)2O3 buffer. Photoluminescence and x-ray photoelectron spectroscopy analyses verified the variations in VO incorporation within α-Ga2O3 grown under different conditions. Finally, owing to the higher incorporation of VO defects within the material, the DUV-PD fabricated based on the α-Ga2O3–500 °C sample exhibited the most pronounced PPC behavior, achieving a maximum PPF index of 143% under a −1 V bias—representing a regulation amplitude of 26.5% compared to the control devices. The dominant VO defects in α-Ga2O3 and variable range hopping led to the PPC behavior observed in the fabricated devices. Our investigation highlights the feasibility of tunable PPC performance in α-Ga2O3-based devices for x-ray to DUV detection and solar-blind neuromorphic vision systems, potentially in harsh environments.
- 1 June 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (6)
Open AccessDefect-modulation in α-Ga2O3 molecular beam epitaxial photodetector investigated through pulsed-light persistent-photoconductivity
α-phase gallium oxide (Ga2O3) features a corundum crystal structure that closely matches the low-cost sapphire substrate commonly used in epitaxy, enabling researchers to perform precise and controllable Ga2O3 epitaxy. It thus offers an excellent material platform for the development of high-power devices and deep ultraviolet photodetectors (DUV-PDs). In this study, we altered the epitaxy properties of α-Ga2O3 grown on m-plane sapphire substrates by changing the growth parameters of oxide molecular beam epitaxy and demonstrated effective modulation of the oxygen vacancy (VO) dependent persistent photoconductivity (PPC) behavior. This gave rise to a tunable paired-pulse facilitation (PPF) index in the fabricated α-Ga2O3-based DUV-PDs. Using α-Ga2O3 grown on bare m-plane sapphire at 500 °C as a benchmark (α-Ga2O3-500 °C), we effectively altered the VO contribution by either increasing the growth temperature to 570 °C or introducing a step-graded α-(AlxGa1−x)2O3 buffer. Photoluminescence and x-ray photoelectron spectroscopy analyses verified the variations in VO incorporation within α-Ga2O3 grown under different conditions. Finally, owing to the higher incorporation of VO defects within the material, the DUV-PD fabricated based on the α-Ga2O3–500 °C sample exhibited the most pronounced PPC behavior, achieving a maximum PPF index of 143% under a −1 V bias—representing a regulation amplitude of 26.5% compared to the control devices. The dominant VO defects in α-Ga2O3 and variable range hopping led to the PPC behavior observed in the fabricated devices. Our investigation highlights the feasibility of tunable PPC performance in α-Ga2O3-based devices for x-ray to DUV detection and solar-blind neuromorphic vision systems, potentially in harsh environments.
- 19 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (7) , 1219-1222
High Rectification, Low Leakage p-Si/n-AlN Heterojunction PN Diode
Ultrawide bandgap AlN is a highly attractive material for power and radio frequency electronics. Unipolar n-AlN Schottky barrier diodes have demonstrated their strengths, whereas further development of AlN-based bipolar devices is desired but lacked. In this letter, we report single-crystalline p-Si/n-AlN p-n diodes (PNDs) with superior performance, accomplished by grafting a p-type Si nanomembrane onto an n-AlN film. Improved Ohmic contact directly on n-AlN was obtained through high temperature annealing at 1100 °C with contact resistivity of 4.9×10-3 Ω cm2. The PNDs exhibited remarkable uniformity across the wafer, excellent rectifying characteristics with a high ratio of ~3×107 at ±10 V, low leakage current density of ~6.25×10-9 A/cm2 at -10 V, and hysteresis-free operation from -10 V to 30 V. Furthermore, the devices demonstrated superior thermal stability, with the on-resistance decreasing from 15.8 to 0.33 Ωcm2 as temperature increased from room temperature to 100 °C, revealing an activation energy of ~425 meV for deep donor state in AlN. No destructive breakdown of the devices was observed up to –894 V. These results highlight the Si/AlN PNDs’ potential for development of AlN-based electronic devices.
- 19 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (7) , 1219-1222
High Rectification, Low Leakage p-Si/n-AlN Heterojunction PN Diode
Ultrawide bandgap AlN is a highly attractive material for power and radio frequency electronics. Unipolar n-AlN Schottky barrier diodes have demonstrated their strengths, whereas further development of AlN-based bipolar devices is desired but lacked. In this letter, we report single-crystalline p-Si/n-AlN p-n diodes (PNDs) with superior performance, accomplished by grafting a p-type Si nanomembrane onto an n-AlN film. Improved Ohmic contact directly on n-AlN was obtained through high temperature annealing at 1100 °C with contact resistivity of 4.9×10-3 Ω cm2. The PNDs exhibited remarkable uniformity across the wafer, excellent rectifying characteristics with a high ratio of ~3×107 at ±10 V, low leakage current density of ~6.25×10-9 A/cm2 at -10 V, and hysteresis-free operation from -10 V to 30 V. Furthermore, the devices demonstrated superior thermal stability, with the on-resistance decreasing from 15.8 to 0.33 Ωcm2 as temperature increased from room temperature to 100 °C, revealing an activation energy of ~425 meV for deep donor state in AlN. No destructive breakdown of the devices was observed up to –894 V. These results highlight the Si/AlN PNDs’ potential for development of AlN-based electronic devices.