Khaled Al-Amoodi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Khaled Al-Amoodi has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Duncan G. Elliott
Department of Electrical and Computer Engineering, University of Alberta, Edmonton, Canada
2 shared publications - Jordan Melzer
Department of Technology Strategy, TELUS Communications, Ottawa, Canada
2 shared publications - Mohammad Mahdi Honari
Intelligent Wireless Technology Laboratory, Electrical and Mechanical Engineering Department, University of Alberta, 9211 116 Street NW, Edmonton, AB T6G 1H9, Canada
2 shared publications - Pedram Mousavi
Department of Mechanical Engineering, Intelligent Wireless Technology Laboratory, University of Alberta, Edmonton, AB, Canada
2 shared publications - Rashid Mirzavand
University of Alberta
2 shared publications Duncan G. Elliott
Department of Electrical and Computer Engineering University of Alberta Edmonton AB T6G 1H9 Canada
1 shared publication
Latest Publications
- Open Access
- 17 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 5 (1) , 46-57
A Compact, Circularly-Polarized, Substrate-Integrated Waveguide, Millimeter-Wave Beamsteering System for 5G Mobile Terminals
A compact, circularly-polarized (CP), end-fire, $4\times 1$ continuous beamsteering antenna array implemented using substrate-integrated waveguides for 5G mobile terminals is proposed in this paper. The purpose of this system is to complement the radiation patterns of planar phased arrays on the faces of a typical mobile terminal. The proposed system seamlessly integrates previously-presented antennas and polarizers, with adjustable phase shifters and a feeding network in a multi-layered, single stack, printed circuit board (PCB) for continuous beamsteering in a compact package. Through the use of forward and reverse couplers, and the stacking of the phase shifters on top of the feeding network, a compact form factor of $7.6\times 4.1\times 0.38\lambda _{o}^{3}$ is achieved. The system was fabricated and assembled through standard PCB processes. The measurements illustrated that the system can achieve a continuous beamsteering range of ±35° with an axial ratio better than 3 dB and a gain variation less than 3 dB. A measured impedance bandwidth (BW) of 8.9% at 28 GHz is also demonstrated. Given its performance, size, ease of manufacture, integrated control lines and single RF feed, the proposed system is a good candidate for 5G millimeter-wave continuous beamsteering in mobile terminals.
- 17 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 5 (1) , 46-57
Open AccessA Compact, Circularly-Polarized, Substrate-Integrated Waveguide, Millimeter-Wave Beamsteering System for 5G Mobile Terminals
A compact, circularly-polarized (CP), end-fire, $4\times 1$ continuous beamsteering antenna array implemented using substrate-integrated waveguides for 5G mobile terminals is proposed in this paper. The purpose of this system is to complement the radiation patterns of planar phased arrays on the faces of a typical mobile terminal. The proposed system seamlessly integrates previously-presented antennas and polarizers, with adjustable phase shifters and a feeding network in a multi-layered, single stack, printed circuit board (PCB) for continuous beamsteering in a compact package. Through the use of forward and reverse couplers, and the stacking of the phase shifters on top of the feeding network, a compact form factor of $7.6\times 4.1\times 0.38\lambda _{o}^{3}$ is achieved. The system was fabricated and assembled through standard PCB processes. The measurements illustrated that the system can achieve a continuous beamsteering range of ±35° with an axial ratio better than 3 dB and a gain variation less than 3 dB. A measured impedance bandwidth (BW) of 8.9% at 28 GHz is also demonstrated. Given its performance, size, ease of manufacture, integrated control lines and single RF feed, the proposed system is a good candidate for 5G millimeter-wave continuous beamsteering in mobile terminals.
- 16 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (12) , 2517-2521
A Compact Substrate Integrated Waveguide Notched-Septum Polarizer for 5G Mobile Devices
- 16 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (12) , 2517-2521
A Compact Substrate Integrated Waveguide Notched-Septum Polarizer for 5G Mobile Devices
- Open Access
- 19 May 2020
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 14 (9) , 980-987
Circularly‐polarised end‐fire antenna and arrays for 5G millimetre‐wave beam‐steering systems
This study presents a circularly‐polarised substrate‐integrated waveguide end‐fire antenna and four‐antenna arrays for 5G beam‐steering mobile devices at 28 GHz. Polarisation is achieved through implementation of a substrate‐integrated waveguide notched‐septum polariser. It is then loaded with a dielectric lens to improve gain, axial ratio bandwidth, and circular polarisation (CP) purity. To suppress the mutual coupling between array elements, vias are extended on either side of the lens. It also improves the single‐element axial ratio and front‐to‐back ratio. The antenna's performance is found to be resilient to typical manufacturing tolerances for the lens and via extensions. The element and arrays are manufactured and measured. The prototypes demonstrated an impedance bandwidth of 11.4% with a maximum array gain of 10.5 dBi and a steering range of up to (with reduced performance when steered to ). Within this range, the antenna array demonstrates a gain variation of up to 3 dB and very good CP purity within the radiation half‐power beamwidths (HPBWs). A wide single‐element elevation HPBW of is also demonstrated. Given its performance and ease of manufacture in a printed circuit board process, the proposed antenna could be a strong candidate for 5G millimetre‐wave beam‐steering systems.
- 19 May 2020
- Published by Institution of Engineering and Technology (IET) in IET Microwaves, Antennas & Propagation
- Vol. 14 (9) , 980-987
Open AccessCircularly‐polarised end‐fire antenna and arrays for 5G millimetre‐wave beam‐steering systems
This study presents a circularly‐polarised substrate‐integrated waveguide end‐fire antenna and four‐antenna arrays for 5G beam‐steering mobile devices at 28 GHz. Polarisation is achieved through implementation of a substrate‐integrated waveguide notched‐septum polariser. It is then loaded with a dielectric lens to improve gain, axial ratio bandwidth, and circular polarisation (CP) purity. To suppress the mutual coupling between array elements, vias are extended on either side of the lens. It also improves the single‐element axial ratio and front‐to‐back ratio. The antenna's performance is found to be resilient to typical manufacturing tolerances for the lens and via extensions. The element and arrays are manufactured and measured. The prototypes demonstrated an impedance bandwidth of 11.4% with a maximum array gain of 10.5 dBi and a steering range of up to (with reduced performance when steered to ). Within this range, the antenna array demonstrates a gain variation of up to 3 dB and very good CP purity within the radiation half‐power beamwidths (HPBWs). A wide single‐element elevation HPBW of is also demonstrated. Given its performance and ease of manufacture in a printed circuit board process, the proposed antenna could be a strong candidate for 5G millimetre‐wave beam‐steering systems.