Zhengpeng Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zhengpeng Wang has a total of 72 co-authors. Here are the top co-authors by number of shared publications:
- Fang-Fang Ren
Nanjing University
13 shared publications J. D. Ye
School of Electronic Science and Engineering, Nanjing University 1 , Nanjing 210023
8 shared publications- Jiandong Ye
Nanjing University
7 shared publications - Hehe Gong
The University of Hong Kong
6 shared publications X. X. Yu
School of Electronic Science and Engineering, Nanjing University , Nanjing 210023
6 shared publications- Rong Zhang
Nanjing University
5 shared publications
Latest Publications
- 28 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (13)
Defect compensation and recombination characteristics of NiO/ β -Ga2O3 heterojunctions under electronic-stopping-dominated swift heavy-ion irradiation
Understanding how irradiation influences recombination-active defects and carrier transport is crucial for establishing the radiation tolerance of Ga2O3 power electronics. Here, we investigate the effects of 1.86 GeV 181Ta31+ swift heavy-ion irradiation on NiO/β-Ga2O3 heterojunction power diodes. Capacitance profiling reveals a pronounced near-surface carrier-removal rate of 9.2 × 107 cm−1 on the β-Ga2O3 side, indicating partial donor compensation in the depletion region. Deep-level transient spectroscopy further reveals irradiation-induced compensation of electrically active defects, in which the E2-related traps (EC-0.818 eV) are no longer resolved within the investigated temperature range, while E2* traps shift deeper from EC-0.670 to EC-0.733 eV and bulk-distributed E9 traps (EC-0.392 eV) remain nearly unchanged. Correspondingly, the subthreshold forward-bias transport behavior changes from tunneling-assisted recombination with a peak ideality factor (η) of 20.75 to a conventional Shockley–Read–Hall recombination mechanism (η≈2) after irradiation, whereas the reverse transport characteristics remain largely consistent with Poole–Frenkel emission with a nearly unchanged activation energy. These results suggest that electronic-stopping-dominated irradiation is accompanied by the compensation of electrically active defects and enhanced carrier compensation within the depletion region, which are associated with the observed changes in the dominant recombination behavior of β-Ga2O3 heterojunction devices under the present irradiation condition.
- 28 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (13)
Defect compensation and recombination characteristics of NiO/ β -Ga2O3 heterojunctions under electronic-stopping-dominated swift heavy-ion irradiation
Understanding how irradiation influences recombination-active defects and carrier transport is crucial for establishing the radiation tolerance of Ga2O3 power electronics. Here, we investigate the effects of 1.86 GeV 181Ta31+ swift heavy-ion irradiation on NiO/β-Ga2O3 heterojunction power diodes. Capacitance profiling reveals a pronounced near-surface carrier-removal rate of 9.2 × 107 cm−1 on the β-Ga2O3 side, indicating partial donor compensation in the depletion region. Deep-level transient spectroscopy further reveals irradiation-induced compensation of electrically active defects, in which the E2-related traps (EC-0.818 eV) are no longer resolved within the investigated temperature range, while E2* traps shift deeper from EC-0.670 to EC-0.733 eV and bulk-distributed E9 traps (EC-0.392 eV) remain nearly unchanged. Correspondingly, the subthreshold forward-bias transport behavior changes from tunneling-assisted recombination with a peak ideality factor (η) of 20.75 to a conventional Shockley–Read–Hall recombination mechanism (η≈2) after irradiation, whereas the reverse transport characteristics remain largely consistent with Poole–Frenkel emission with a nearly unchanged activation energy. These results suggest that electronic-stopping-dominated irradiation is accompanied by the compensation of electrically active defects and enhanced carrier compensation within the depletion region, which are associated with the observed changes in the dominant recombination behavior of β-Ga2O3 heterojunction devices under the present irradiation condition.
- 21 October 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (17)
Fast switching Ga2O3 Schottky barrier power diode with beveled-mesa and BaTiO3 field plate edge termination
Power devices rely on ideal edge termination to suppress the electric field crowding and avoid premature breakdown before the material's critical field is reached. In this work, a hybrid electric field management configuration, featuring the combination of beveled-mesa (BM) termination and high-k oxide BaTiO3 field plate (FP), was implemented in Ga2O3 Schottky barrier diodes (SBDs). This BMFP-SBD realizes a breakdown voltage (BV) of 1.7 kV with extremely low reverse leakage current, outperforming the BM terminated SBD with BV of 0.64 kV and bare SBD with BV of 0.22 kV. Based on the temperature-dependent reverse characteristics, the dominant leakage mechanism transforms from Poole–Frenkel (P–F) emission in BM-SBD to variable-range-hopping (VRH) in BMFP-SBD at high bias. In particular, under switching conditions of di/dt up to 420 A/μs, the BMFP-SBD exhibits superior dynamic switching characteristics with a short reverse recovery time of 10.1 ns, which are comparable with those in advanced commercial SiC SBDs. These findings underscore the potential of Ga2O3 SBD enabled by BM and high-k FP edge termination for high-speed and high-voltage power electronics applications.
- 21 October 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (17)
Fast switching Ga2O3 Schottky barrier power diode with beveled-mesa and BaTiO3 field plate edge termination
Power devices rely on ideal edge termination to suppress the electric field crowding and avoid premature breakdown before the material's critical field is reached. In this work, a hybrid electric field management configuration, featuring the combination of beveled-mesa (BM) termination and high-k oxide BaTiO3 field plate (FP), was implemented in Ga2O3 Schottky barrier diodes (SBDs). This BMFP-SBD realizes a breakdown voltage (BV) of 1.7 kV with extremely low reverse leakage current, outperforming the BM terminated SBD with BV of 0.64 kV and bare SBD with BV of 0.22 kV. Based on the temperature-dependent reverse characteristics, the dominant leakage mechanism transforms from Poole–Frenkel (P–F) emission in BM-SBD to variable-range-hopping (VRH) in BMFP-SBD at high bias. In particular, under switching conditions of di/dt up to 420 A/μs, the BMFP-SBD exhibits superior dynamic switching characteristics with a short reverse recovery time of 10.1 ns, which are comparable with those in advanced commercial SiC SBDs. These findings underscore the potential of Ga2O3 SBD enabled by BM and high-k FP edge termination for high-speed and high-voltage power electronics applications.
- 17 April 2024
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 11 (2)
Performance limiting inhomogeneities of defect states in ampere-class Ga2O3 power diodes
Impacts of spatial charge inhomogeneities on carrier transport fluctuations and premature breakdown were investigated in Schottky ampere-class Ga2O3 power diodes. Three prominent electron traps were detected in Ga2O3 epilayers by a combination of the depth-resolved capacitance spectroscopy profiling and gradual dry etching. The near-surface trap occurring at 1.06 eV below the conduction band minimum (EC), named E3, was found to be confined within a 180 nm surface region of the Ga2O3 epilayers. Two bulk traps at EC − 0.75 eV (E2*) and at EC − 0.82 eV (E2) were identified and interconnected with the VGa- and FeGa-type defects, respectively. In the framework of the impact ionization model, employing the experimental trap parameters, the TCAD simulated breakdown characteristics matched the experimental breakdown properties well, consistently with inverse proportionality to the total trap densities. In particular, the shallowest distributed E3 trap with the deepest level is responsible for higher leakage and premature breakdown. In contrast, Ga2O3 Schottky diodes without E3 trap exhibit enhanced breakdown voltages, and the leakage mechanism evolves from variable range hopping at medium reverse voltages, to the space-charge-limited conduction at high reverse biases. This work bridges the fundamental gap between spatial charge inhomogeneities and diode breakdown features, paving the way for more reliable defect engineering in high-performance Ga2O3 power devices.
- 17 April 2024
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 11 (2)
Performance limiting inhomogeneities of defect states in ampere-class Ga2O3 power diodes
Impacts of spatial charge inhomogeneities on carrier transport fluctuations and premature breakdown were investigated in Schottky ampere-class Ga2O3 power diodes. Three prominent electron traps were detected in Ga2O3 epilayers by a combination of the depth-resolved capacitance spectroscopy profiling and gradual dry etching. The near-surface trap occurring at 1.06 eV below the conduction band minimum (EC), named E3, was found to be confined within a 180 nm surface region of the Ga2O3 epilayers. Two bulk traps at EC − 0.75 eV (E2*) and at EC − 0.82 eV (E2) were identified and interconnected with the VGa- and FeGa-type defects, respectively. In the framework of the impact ionization model, employing the experimental trap parameters, the TCAD simulated breakdown characteristics matched the experimental breakdown properties well, consistently with inverse proportionality to the total trap densities. In particular, the shallowest distributed E3 trap with the deepest level is responsible for higher leakage and premature breakdown. In contrast, Ga2O3 Schottky diodes without E3 trap exhibit enhanced breakdown voltages, and the leakage mechanism evolves from variable range hopping at medium reverse voltages, to the space-charge-limited conduction at high reverse biases. This work bridges the fundamental gap between spatial charge inhomogeneities and diode breakdown features, paving the way for more reliable defect engineering in high-performance Ga2O3 power devices.
- 10 January 2024
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 15 (2) , 556-564
Ga2O3 Bipolar Heterojunction-Based Optoelectronic Synapse Array with Visual Attention
The human brain efficiently processes only a fraction of visual information, a phenomenon termed attentional control, resulting in energy savings and heightened adaptability. Translating this mechanism into artificial visual neurons holds promise for constructing energy-efficient, bioinspired visual systems. Here, we propose a self-rectifying artificial visual neuron (SEVN) based on a NiO/Ga2O3 bipolar heterojunction with attentional control on patterns with a target color. The device exhibits short-term potentiation (STP) with quantum point contact (QPC) traits at low bias and transitions to long-term potentiation (LTP) at high bias, particularly facilitated by electron capture in deep defects upon ultraviolet (UV) exposure. With the utilization of two wavelengths of light upon the target and interference part of CAPTCHA to simulate top-down attentional control, the recognition accuracy is enhanced from 74 to 84%. These findings have the potential to augment the visual capability of neuromorphic systems with implications for diverse applications, including cybersecurity, healthcare, and machine vision.
- 10 January 2024
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 15 (2) , 556-564
Ga2O3 Bipolar Heterojunction-Based Optoelectronic Synapse Array with Visual Attention
The human brain efficiently processes only a fraction of visual information, a phenomenon termed attentional control, resulting in energy savings and heightened adaptability. Translating this mechanism into artificial visual neurons holds promise for constructing energy-efficient, bioinspired visual systems. Here, we propose a self-rectifying artificial visual neuron (SEVN) based on a NiO/Ga2O3 bipolar heterojunction with attentional control on patterns with a target color. The device exhibits short-term potentiation (STP) with quantum point contact (QPC) traits at low bias and transitions to long-term potentiation (LTP) at high bias, particularly facilitated by electron capture in deep defects upon ultraviolet (UV) exposure. With the utilization of two wavelengths of light upon the target and interference part of CAPTCHA to simulate top-down attentional control, the recognition accuracy is enhanced from 74 to 84%. These findings have the potential to augment the visual capability of neuromorphic systems with implications for diverse applications, including cybersecurity, healthcare, and machine vision.
- 9 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (11) , 5596-5602
High-V TH E-Mode GaN HEMTs With Robust Gate-Bias-Dependent V TH Stability Enabled by Mg-Doped p-GaN Engineering
Highly stable threshold voltage$({V}_{\text {TH}})$ characteristics are an essential reliability requirement for p -GaN/AlGaN/GaN high-electron-mobility transistors (p-GaN HEMTs) to withstand various gate bias stresses for power applications. In this work, we demonstrate high-${V}_{\text {TH}}$ (3.0 V) p-GaN HEMTs with robust${V}_{\text {TH}}$ stability by p -GaN gate engineering via Mg doping and activation. The${V}_{\text {TH}}$ degradation rates of the resulting device under both pulsed-${I}/{V}$ and bias temperature instability (BTI) stress conditions are less than 10% at high temperatures up to 150°, which is much lower than that of conventional Schottky-type p -GaN HEMTs (20%–30%). Such notable${V}_{\text {TH}}$ characteristics are due to the impact ionization (I.I.)-dependent hole compensation under certain gate stress, which effectively alleviates the electron trapping effect and reduces positive${V}_{\text {TH}}$ shift. The I.I. occurring in the fully depleted p -GaN layer has been confirmed by both positive temperature-dependent gate breakdown characteristics and numerical simulations. Furthermore, shallow- and deep-level hole traps are identified in the gate-stack of high-${V}_{\text {TH}}$ devices by performing the deep-level transient spectroscopy (DLTS) technique. Consequently, the trapping effect associated with hole traps may also alleviate the undesired electron-trapping-induced${V}_{\text {TH}}$ shift. These results provide a critical understanding of the${V}_{\text {TH}}$ stability of the high-${V}_{\text {TH}}$ p -GaN HEMTs (HVT-HEMTs) and important design guidance for commercial device development.- 9 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (11) , 5596-5602
High-V TH E-Mode GaN HEMTs With Robust Gate-Bias-Dependent V TH Stability Enabled by Mg-Doped p-GaN Engineering
Highly stable threshold voltage$({V}_{\text {TH}})$ characteristics are an essential reliability requirement for p -GaN/AlGaN/GaN high-electron-mobility transistors (p-GaN HEMTs) to withstand various gate bias stresses for power applications. In this work, we demonstrate high-${V}_{\text {TH}}$ (3.0 V) p-GaN HEMTs with robust${V}_{\text {TH}}$ stability by p -GaN gate engineering via Mg doping and activation. The${V}_{\text {TH}}$ degradation rates of the resulting device under both pulsed-${I}/{V}$ and bias temperature instability (BTI) stress conditions are less than 10% at high temperatures up to 150°, which is much lower than that of conventional Schottky-type p -GaN HEMTs (20%–30%). Such notable${V}_{\text {TH}}$ characteristics are due to the impact ionization (I.I.)-dependent hole compensation under certain gate stress, which effectively alleviates the electron trapping effect and reduces positive${V}_{\text {TH}}$ shift. The I.I. occurring in the fully depleted p -GaN layer has been confirmed by both positive temperature-dependent gate breakdown characteristics and numerical simulations. Furthermore, shallow- and deep-level hole traps are identified in the gate-stack of high-${V}_{\text {TH}}$ devices by performing the deep-level transient spectroscopy (DLTS) technique. Consequently, the trapping effect associated with hole traps may also alleviate the undesired electron-trapping-induced${V}_{\text {TH}}$ shift. These results provide a critical understanding of the${V}_{\text {TH}}$ stability of the high-${V}_{\text {TH}}$ p -GaN HEMTs (HVT-HEMTs) and important design guidance for commercial device development.- Open Access
- 3 July 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (1)
A self-aligned Ga2O3 heterojunction barrier Schottky power diode
We report an alignment-free gallium oxide (Ga2O3) heterojunction barrier Schottky (HJBS) power diode, which utilizes the self-assembled Ni nanostructures as in situ masks for the trench etching of Ga2O3 and the subsequent selective-area filling of p-type NiO. By increasing the trench depth to 200 nm, the relevant HJBS diode exhibits improved reverse blocking capabilities including the reduced leakage current density of 10−8 A/cm2 (at a reverse bias of 100 V) and the enhanced breakdown voltage of 748 V, while maintaining the forward biasing characteristics similar to the Schottky barrier diode (SBD). The variation of turn-on voltage and the reverse breakdown features indicate the conversion of the HJBS diodes characteristics from Ni/Ga2O3 SBD to the NiO/Ga2O3 p-n heterojunction diode. The electrical field simulations and experimental facts imply that the remarkable lateral pinch-off effect in the 200-nm trenched diodes shields the electric field in the depletion region underneath the Ni/Ga2O3 Schottky contact. This work provides a straightforward strategy to simplify the fabrication process of Ga2O3-based HJBS diodes with both promising forward and reverse performances.
- 3 July 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (1)
Open AccessA self-aligned Ga2O3 heterojunction barrier Schottky power diode
We report an alignment-free gallium oxide (Ga2O3) heterojunction barrier Schottky (HJBS) power diode, which utilizes the self-assembled Ni nanostructures as in situ masks for the trench etching of Ga2O3 and the subsequent selective-area filling of p-type NiO. By increasing the trench depth to 200 nm, the relevant HJBS diode exhibits improved reverse blocking capabilities including the reduced leakage current density of 10−8 A/cm2 (at a reverse bias of 100 V) and the enhanced breakdown voltage of 748 V, while maintaining the forward biasing characteristics similar to the Schottky barrier diode (SBD). The variation of turn-on voltage and the reverse breakdown features indicate the conversion of the HJBS diodes characteristics from Ni/Ga2O3 SBD to the NiO/Ga2O3 p-n heterojunction diode. The electrical field simulations and experimental facts imply that the remarkable lateral pinch-off effect in the 200-nm trenched diodes shields the electric field in the depletion region underneath the Ni/Ga2O3 Schottky contact. This work provides a straightforward strategy to simplify the fabrication process of Ga2O3-based HJBS diodes with both promising forward and reverse performances.
- 10 April 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (15) , 152102
Traps inhomogeneity induced conversion of Shockley–Read–Hall recombination in NiO/β-Ga2O3 p+–n heterojunction diodes
In this Letter, the trap inhomogeneity within β-Ga2O3 is correlated with the conversion of Shockley–Read–Hall (SRH) recombination in NiO/β-Ga2O3 p+–n heterojunction diodes. For the virgin epi-wafer, both near-surface traps E2 (EC-0.82 eV) and E3 (EC-1.11 eV) and bulk E2* traps (EC-0.76 eV) are identified by a transient capacitance analysis, and the corresponding forward current–voltage characteristics of diodes are well fitted in the framework of field-dependent SRH recombination. The SRH recombination rates for E2, E3, and E2* traps are determined to be 1.3 × 107, 8.6 × 108, and 2.4 × 108 s−1, respectively. In this circumstance, carrier transport under forward bias is governed by trap-assisted tunneling through E3 traps with high recombination rates, and the hysteresis is pronounced. With the removal of the defective surface layer, E2 and E3 traps are almost completely eliminated, together with the reduced density of E2* traps to 5.6 × 1014 cm−3. The resultant diode performs an improved rectification ratio of >1011 at ±3 V and an enhanced reverse breakdown voltage of 1692 V. The elimination of near-surface traps leads to the conversion of carrier transport into the conventional SRH recombination, accompanied by the negligible forward hysteresis characteristics. The established fundamental correlation of carrier transport and traps within Ga2O3 is beneficial to develop a high-performance power rectifier toward practical applications.
- 10 April 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (15) , 152102
Traps inhomogeneity induced conversion of Shockley–Read–Hall recombination in NiO/β-Ga2O3 p+–n heterojunction diodes
In this Letter, the trap inhomogeneity within β-Ga2O3 is correlated with the conversion of Shockley–Read–Hall (SRH) recombination in NiO/β-Ga2O3 p+–n heterojunction diodes. For the virgin epi-wafer, both near-surface traps E2 (EC-0.82 eV) and E3 (EC-1.11 eV) and bulk E2* traps (EC-0.76 eV) are identified by a transient capacitance analysis, and the corresponding forward current–voltage characteristics of diodes are well fitted in the framework of field-dependent SRH recombination. The SRH recombination rates for E2, E3, and E2* traps are determined to be 1.3 × 107, 8.6 × 108, and 2.4 × 108 s−1, respectively. In this circumstance, carrier transport under forward bias is governed by trap-assisted tunneling through E3 traps with high recombination rates, and the hysteresis is pronounced. With the removal of the defective surface layer, E2 and E3 traps are almost completely eliminated, together with the reduced density of E2* traps to 5.6 × 1014 cm−3. The resultant diode performs an improved rectification ratio of >1011 at ±3 V and an enhanced reverse breakdown voltage of 1692 V. The elimination of near-surface traps leads to the conversion of carrier transport into the conventional SRH recombination, accompanied by the negligible forward hysteresis characteristics. The established fundamental correlation of carrier transport and traps within Ga2O3 is beneficial to develop a high-performance power rectifier toward practical applications.
- 28 July 2022
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 13 (30) , 7094-7099
Identification and Suppression of Majority Surface States in the Dry-Etched β-Ga2O3
Surface treatment after dry etching is vital to enhance the surface quality of the material and thus improve device performance. In this Letter, we identified the majority surface states induced by the dry etching of β-Ga2O3 and optimized surface treatments to suppress these electrically active defects with the improved performance of Schottky barrier diodes. Transient spectroscopies suggested that the majority traps (EC-0.75 eV) related to divacancies (VGa-VO) were enhanced in the concentration of 3.37 × 1014 cm-3 by dry etching and reduced to 0.90 × 1014 cm-3 by the combined means of oxygen annealing and piranha solution treatment. The trap evolution is supported by the suppressed donor-acceptor pair radiative recombination related to oxygen vacancies, the improved carrier transport (negligible hysteresis current-voltage and unity ideality factor), and the reduced surface band bending. These findings provide a straightforward strategy to improve surface quality for the further performance improvement of Ga2O3 power diodes.
- 28 July 2022
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 13 (30) , 7094-7099
Identification and Suppression of Majority Surface States in the Dry-Etched β-Ga2O3
Surface treatment after dry etching is vital to enhance the surface quality of the material and thus improve device performance. In this Letter, we identified the majority surface states induced by the dry etching of β-Ga2O3 and optimized surface treatments to suppress these electrically active defects with the improved performance of Schottky barrier diodes. Transient spectroscopies suggested that the majority traps (EC-0.75 eV) related to divacancies (VGa-VO) were enhanced in the concentration of 3.37 × 1014 cm-3 by dry etching and reduced to 0.90 × 1014 cm-3 by the combined means of oxygen annealing and piranha solution treatment. The trap evolution is supported by the suppressed donor-acceptor pair radiative recombination related to oxygen vacancies, the improved carrier transport (negligible hysteresis current-voltage and unity ideality factor), and the reduced surface band bending. These findings provide a straightforward strategy to improve surface quality for the further performance improvement of Ga2O3 power diodes.
- 21 July 2022
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 55 (39) , 394003
Photoconductive and photovoltaic metal-semiconductor-metal κ-Ga2O3 solar-blind detectors with high rejection ratios
The metal-semiconductor-metal (MSM) structure is a popular architecture for developing Ga2O3 solar blind photodetectors. The nature of metal-semiconductor contact is decisive for the operation mode, gain mechanism and device performances. In this contribution, κ-Ga2O3 MSM solar-blind photodetectors with Ti/Ga2O3 Ohmic and Ni/Ga2O3 Schottky contacts were constructed on the high-quality Si-doped κ-Ga2O3 epilayer grown by hydride vapor phase epitaxy. The Ti/κ-Ga2O3/Ti Ohmic MSM device is operated in a photoconductive mode, exhibiting a maximum responsivity of 322.5 A W−1 and a high rejection ratio of over 105, but with an undesirable sub-gap response and high dark current. In comparison, the Ni/Ga2O3/Ni photodiode with a back-to-back Schottky configuration is operated in a mixed photovoltaic and photoconductive mode, demonstrating a decent photoresponsivity of 0.37 A W−1, a maintained high rejection ratio of 1.16 × 105, a detectivity of 3.51 × 1013 Jones and the elimination of slow photoresponse from sub-gap states. The frequency-dependent photoresponse and transient photocurrent characteristics indicate that the persistent photoconductivity effect is responsible for the high gain achieved in the Ti/Ga2O3/Ti photoconductor, and the dominant slow transient decay component is a fingerprint of photoexcited carrier trapping and repopulation. The response speed is improved in the Ni/Ga2O3/Ni Schottky MSM device, whereas carrier transport across interdigitated fingers is affected by bulk traps, limiting the overall response-bandwidth merit.
- 21 July 2022
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 55 (39) , 394003
Photoconductive and photovoltaic metal-semiconductor-metal κ-Ga2O3 solar-blind detectors with high rejection ratios
The metal-semiconductor-metal (MSM) structure is a popular architecture for developing Ga2O3 solar blind photodetectors. The nature of metal-semiconductor contact is decisive for the operation mode, gain mechanism and device performances. In this contribution, κ-Ga2O3 MSM solar-blind photodetectors with Ti/Ga2O3 Ohmic and Ni/Ga2O3 Schottky contacts were constructed on the high-quality Si-doped κ-Ga2O3 epilayer grown by hydride vapor phase epitaxy. The Ti/κ-Ga2O3/Ti Ohmic MSM device is operated in a photoconductive mode, exhibiting a maximum responsivity of 322.5 A W−1 and a high rejection ratio of over 105, but with an undesirable sub-gap response and high dark current. In comparison, the Ni/Ga2O3/Ni photodiode with a back-to-back Schottky configuration is operated in a mixed photovoltaic and photoconductive mode, demonstrating a decent photoresponsivity of 0.37 A W−1, a maintained high rejection ratio of 1.16 × 105, a detectivity of 3.51 × 1013 Jones and the elimination of slow photoresponse from sub-gap states. The frequency-dependent photoresponse and transient photocurrent characteristics indicate that the persistent photoconductivity effect is responsible for the high gain achieved in the Ti/Ga2O3/Ti photoconductor, and the dominant slow transient decay component is a fingerprint of photoexcited carrier trapping and repopulation. The response speed is improved in the Ni/Ga2O3/Ni Schottky MSM device, whereas carrier transport across interdigitated fingers is affected by bulk traps, limiting the overall response-bandwidth merit.
- 21 March 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (12) , 121601
Dislocation dynamics in α-Ga2O3 micropillars from selective-area epitaxy to epitaxial lateral overgrowth
Epitaxial lateral overgrowth (ELO) is an effective strategy to achieve metastable phased α-Ga2O3 with low dislocation densities, which is desirable for developing ultralow-loss and ultrahigh power devices, whereas the involved dislocation dynamics have not been fully exploited. In this Letter, we investigated the dislocation propagations and reactions in α-Ga2O3 micropillar arrays selectively grown by halide vapor phase epitaxy technique. Screw dislocations in α-Ga2O3 micropillars grown from the selective area epitaxy (SAE) to ELO mode exhibited an independent character with an average density of 4.5 × 106 cm−2 while the edge dislocation density was reduced to 5.3 × 108 cm−2. During the initial SAE process, the α-Ga2O3 hexagonal pyramid is developed with the observed inversion domains within the pillar cores. The successive epitaxial lateral overgrowth ELO facilitates the formation of inclined facets upon the SiO2 mask. Almost complete filtering of the underlying threading dislocation has been demonstrated in the ELO wings. Strong image forces induced by inclined free surfaces drive the propagation and reaction of threading dislocations until annihilation, which is well described by the dislocation-filtering model during the dynamic geometry transition of micropillars. These findings may pave the way for the success of the heteroepitaxy of low dislocation density α-Ga2O3 toward the development of high-performance power devices.
- 21 March 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (12) , 121601
Dislocation dynamics in α-Ga2O3 micropillars from selective-area epitaxy to epitaxial lateral overgrowth
Epitaxial lateral overgrowth (ELO) is an effective strategy to achieve metastable phased α-Ga2O3 with low dislocation densities, which is desirable for developing ultralow-loss and ultrahigh power devices, whereas the involved dislocation dynamics have not been fully exploited. In this Letter, we investigated the dislocation propagations and reactions in α-Ga2O3 micropillar arrays selectively grown by halide vapor phase epitaxy technique. Screw dislocations in α-Ga2O3 micropillars grown from the selective area epitaxy (SAE) to ELO mode exhibited an independent character with an average density of 4.5 × 106 cm−2 while the edge dislocation density was reduced to 5.3 × 108 cm−2. During the initial SAE process, the α-Ga2O3 hexagonal pyramid is developed with the observed inversion domains within the pillar cores. The successive epitaxial lateral overgrowth ELO facilitates the formation of inclined facets upon the SiO2 mask. Almost complete filtering of the underlying threading dislocation has been demonstrated in the ELO wings. Strong image forces induced by inclined free surfaces drive the propagation and reaction of threading dislocations until annihilation, which is well described by the dislocation-filtering model during the dynamic geometry transition of micropillars. These findings may pave the way for the success of the heteroepitaxy of low dislocation density α-Ga2O3 toward the development of high-performance power devices.