Djoko Wahyu Karmiadji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Djoko Wahyu Karmiadji has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
Abdul Rohman Farid
The Indonesian Railroad Industry (INKA), Indonesia
2 shared publicationsAnwar Anwar
National Agency for the Research and Innovation, Indonesia
2 shared publicationsBudi Haryanto
National Agency for the Research and Innovation, Indonesia
2 shared publications- Mohammad Rosyidi
National Research and Innovation Agency, Indonesia
2 shared publications Muchamad Gozali
Agency for the Assessment and Application of Technology, Indonesia
2 shared publications- Muji Setiyo
Muhammadiyah University of Magelang
2 shared publications
Latest Publications
- Open Access
- 5 December 2025
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 8 (3) , 716-725
Ramie-PLA Composite Hollow Sections for EV Chassis: Development and Static Bending Test
The increasing demand for sustainable and lightweight materials in the transportation sector, particularly in the context of electric vehicles (EVs), has accelerated the exploration of bio-based composites as viable alternatives to conventional structural materials. This study investigates the mechanical performance of hollow structural components fabricated from polylactic acid (PLA)-based composites reinforced with natural ramie fibers, targeting their application as chassis elements in urban electric vehicles. Emphasis is placed on replacing commercial steel hollow sections with environmentally benign alternatives that maintain mechanical integrity while offering additional functional benefits such as electrical non-conductivity. Three-point bending tests were conducted to evaluate the composite specimens' flexural strength, stiffness, and failure behavior to assess structural viability. This method was selected for its relevance to real-world bending stresses encountered in vehicular chassis components and suitability for consistent evaluation across beam-like geometries. Results demonstrate that the ramie-PLA bio-composite exhibits promising flexural performance, with sufficient bendability and stiffness for potential structural integration. Furthermore, the non-conductive nature of the composite presents a significant advantage for reducing electromagnetic interference with sensitive electronic systems common in EV platforms. The findings support the feasibility of deploying natural fiber-reinforced PLA composites as a sustainable, cost-effective solution for lightweight automotive structures, particularly in emerging markets where urban EV adoption is rapidly expanding.
- 5 December 2025
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 8 (3) , 716-725
Open AccessRamie-PLA Composite Hollow Sections for EV Chassis: Development and Static Bending Test
The increasing demand for sustainable and lightweight materials in the transportation sector, particularly in the context of electric vehicles (EVs), has accelerated the exploration of bio-based composites as viable alternatives to conventional structural materials. This study investigates the mechanical performance of hollow structural components fabricated from polylactic acid (PLA)-based composites reinforced with natural ramie fibers, targeting their application as chassis elements in urban electric vehicles. Emphasis is placed on replacing commercial steel hollow sections with environmentally benign alternatives that maintain mechanical integrity while offering additional functional benefits such as electrical non-conductivity. Three-point bending tests were conducted to evaluate the composite specimens' flexural strength, stiffness, and failure behavior to assess structural viability. This method was selected for its relevance to real-world bending stresses encountered in vehicular chassis components and suitability for consistent evaluation across beam-like geometries. Results demonstrate that the ramie-PLA bio-composite exhibits promising flexural performance, with sufficient bendability and stiffness for potential structural integration. Furthermore, the non-conductive nature of the composite presents a significant advantage for reducing electromagnetic interference with sensitive electronic systems common in EV platforms. The findings support the feasibility of deploying natural fiber-reinforced PLA composites as a sustainable, cost-effective solution for lightweight automotive structures, particularly in emerging markets where urban EV adoption is rapidly expanding.
- Open Access
- 15 July 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (2) , 425-433
Experimental study on a new prototype design of electric bus vehicle structure under torsion loading conditions
Vehicles commonly encounter uneven road conditions, which can lead to torsional deformation of the frame structure. The results of finite element analysis (FEA) indicate that the highest stress occurs under torsion loading conditions. To validate these simulation results, an experimental study was conducted involving static load testing under torsional loading conditions on a hybrid frame structure, composed of SS 400 carbon steel and 6061 aluminum alloy, designed for a 70-passenger electric bus. The test was performed by applying a static load of 6,825 kg as sandbags on the seating area and aisle, and supporting the frame on three wheels only. Strain measurements were recorded using 28 strain gauges: 20 on the SS 400 carbon steel underframe and 8 on the 6061 aluminum alloy structure of the side and roof frames. The total load was the weight of 70 passengers plus a 30% dynamic load factor. Experimental analysis revealed a maximum stress value of 76.42 MPa in the SS 400 carbon steel of the underframe at location 9 in the central section of the underframe. In the 6061 aluminum alloy structure, the maximum stress value of 15.56 MPa was obtained in the roof frame directly below the air conditioner unit. Overall, the measured stress values were within the elastic ranges of the materials used, demonstrating structural integrity under load. The average difference between the experimental results for stress and the finite element analysis (FEA) simulation was approximately 11.21%.
- 15 July 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (2) , 425-433
Open AccessExperimental study on a new prototype design of electric bus vehicle structure under torsion loading conditions
Vehicles commonly encounter uneven road conditions, which can lead to torsional deformation of the frame structure. The results of finite element analysis (FEA) indicate that the highest stress occurs under torsion loading conditions. To validate these simulation results, an experimental study was conducted involving static load testing under torsional loading conditions on a hybrid frame structure, composed of SS 400 carbon steel and 6061 aluminum alloy, designed for a 70-passenger electric bus. The test was performed by applying a static load of 6,825 kg as sandbags on the seating area and aisle, and supporting the frame on three wheels only. Strain measurements were recorded using 28 strain gauges: 20 on the SS 400 carbon steel underframe and 8 on the 6061 aluminum alloy structure of the side and roof frames. The total load was the weight of 70 passengers plus a 30% dynamic load factor. Experimental analysis revealed a maximum stress value of 76.42 MPa in the SS 400 carbon steel of the underframe at location 9 in the central section of the underframe. In the 6061 aluminum alloy structure, the maximum stress value of 15.56 MPa was obtained in the roof frame directly below the air conditioner unit. Overall, the measured stress values were within the elastic ranges of the materials used, demonstrating structural integrity under load. The average difference between the experimental results for stress and the finite element analysis (FEA) simulation was approximately 11.21%.
- Open Access
- 4 August 2024
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 7 (2) , 236-251
The Road Safety: Utilising Machine Learning Approach for Predicting Fatality in Toll Road Accidents
Road safety is one of the critical government transportation concerns, especially on the toll roads. With the increasing number of toll roads as part of infrastructure planning, road traffic accidents are significantly escalating. Developing a system that predicts accidents on toll roads will benefit to reduce the harm that is caused by traffic accidents. This study will propose a method for analysing toll road accidents in Indonesia using historical toll road accident data as a dataset to become a pattern to examine the frequency of accidents. This dataset consists of various parameters from three main factors that cause accidents: human, environmental, and road infrastructure factors. Machine learning technique will be mainly used to determine the most influencing factors by employing classifiers such as Logistic Regression (LR), Decision Tree (DT), Gaussian Naïve Bayes (GNB), and K-Nearest Neighbors (KNN) can construct the prediction model. Fourteen subfactors from the data were used to predict the future fatalities caused by accidents, which allowed the system to forecast the accident fatality. The results show accuracy performance on the test set with LR, DT, KNN, and GNB models, 85.3%, 79.4%, 87.1%, and 77.1%, respectively. The KNN Classifier model has the most minor error value of 0.6 compared to the other models. The study”™s findings will help analyse the causal factors involved in toll road accidents and could be utilised by road authorities to employ risk control options to mitigate the ramifications.
- 4 August 2024
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 7 (2) , 236-251
Open AccessThe Road Safety: Utilising Machine Learning Approach for Predicting Fatality in Toll Road Accidents
Road safety is one of the critical government transportation concerns, especially on the toll roads. With the increasing number of toll roads as part of infrastructure planning, road traffic accidents are significantly escalating. Developing a system that predicts accidents on toll roads will benefit to reduce the harm that is caused by traffic accidents. This study will propose a method for analysing toll road accidents in Indonesia using historical toll road accident data as a dataset to become a pattern to examine the frequency of accidents. This dataset consists of various parameters from three main factors that cause accidents: human, environmental, and road infrastructure factors. Machine learning technique will be mainly used to determine the most influencing factors by employing classifiers such as Logistic Regression (LR), Decision Tree (DT), Gaussian Naïve Bayes (GNB), and K-Nearest Neighbors (KNN) can construct the prediction model. Fourteen subfactors from the data were used to predict the future fatalities caused by accidents, which allowed the system to forecast the accident fatality. The results show accuracy performance on the test set with LR, DT, KNN, and GNB models, 85.3%, 79.4%, 87.1%, and 77.1%, respectively. The KNN Classifier model has the most minor error value of 0.6 compared to the other models. The study”™s findings will help analyse the causal factors involved in toll road accidents and could be utilised by road authorities to employ risk control options to mitigate the ramifications.
- Open Access
- 24 November 2023
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 6 (3) , 584-598
Theoretical Experiments on Road Profile Data Analysis using Filter Combinations
Identification of road profiles is needed to provide the input of automotive simulation and endurance testing. The analysis with estimation methods is mostly done to identify road profiles. The main goal of analysis methods is to obtain the data of vertical displacements due to road profile measurement. The acceleration data is obtained from measuring road profile by using 4 sensors of accelerometer placed on each car wheel. The measuring data is converted to be vertical displacement data by using a "double integrator", however, it is not easy to get accurate results since the signal obtained carries a lot of noise and it is necessary to design the right filter reduce the noise. In this study, the signal filtering methods reducing the noise were used Fast Fourier Transform (FFT) and Kalman Filter (KF) combination. Experiments were carried out by combining Fast Fourier Transform and Kalman Filters using an input signal with unit (volt) in the time domain. In addition, this research focused on preparing the survey data that has been obtained by eliminating the noise to convert becoming the displacement input data for providing the loads of automotive simulation testing.
- 24 November 2023
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 6 (3) , 584-598
Open AccessTheoretical Experiments on Road Profile Data Analysis using Filter Combinations
Identification of road profiles is needed to provide the input of automotive simulation and endurance testing. The analysis with estimation methods is mostly done to identify road profiles. The main goal of analysis methods is to obtain the data of vertical displacements due to road profile measurement. The acceleration data is obtained from measuring road profile by using 4 sensors of accelerometer placed on each car wheel. The measuring data is converted to be vertical displacement data by using a "double integrator", however, it is not easy to get accurate results since the signal obtained carries a lot of noise and it is necessary to design the right filter reduce the noise. In this study, the signal filtering methods reducing the noise were used Fast Fourier Transform (FFT) and Kalman Filter (KF) combination. Experiments were carried out by combining Fast Fourier Transform and Kalman Filters using an input signal with unit (volt) in the time domain. In addition, this research focused on preparing the survey data that has been obtained by eliminating the noise to convert becoming the displacement input data for providing the loads of automotive simulation testing.
- Open Access
- 5 January 2022
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 2 (1) , 42-53
Verification of urban light rail transit (LRT) bogie frame structure design lifetime under variable fatigue loads
The bogie frame is the main structure of the train that supports the train's loads during its operation. These structures are subject to fatigue testing to ensure their design life is up to the required standards. The urban light rail transit (LRT) bogie frame used in the Greater Jakarta area is newly designed and manufactured by a commercial railway rolling stock manufacturer. The design lifetime of this newly designed bogie frame structure under various fatigue load conditions is verified experimentally by fatigue testing. Testing and evaluations were conducted following the EN 13749 standard and VDV recommendation. The fatigue test of the urban LRT bogie frame structure was carried out in the test hall of the BPPT Structural Strength Technology Center (B2TKS) using a combination of seven loadings. The bogie frame was subjected to two variable types of fatigue loads, namely driving in curves and passing points (switches), with 2,000,000 cycles, 4,000,000 cycles, and 6,000,000 cycles of fatigue loadings. The parameter measured on the bogie frame structure is the strain value during the test using a dynamic data logger. The stress values analyzed are the average stress and the stress amplitude and then plotted on the maximum and minimum stress curve. The bogie structure is inspected by the non-destructive test method in all areas of its welded joints. This inspection is carried out before and after the test to ensure whether there are cracks caused by fatigue loads. The results of the fatigue test on the bogie structure under the variable fatigue load conditions show that the maximum stress value of 91.71 MPa at 1,500,000 cycles, that occurs during the test, does not exceed the fatigue limit of the material, and there are no cracks in the structure after the test is carried out for up to 6,000,000 cycles.
- 5 January 2022
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 2 (1) , 42-53
Open AccessVerification of urban light rail transit (LRT) bogie frame structure design lifetime under variable fatigue loads
The bogie frame is the main structure of the train that supports the train's loads during its operation. These structures are subject to fatigue testing to ensure their design life is up to the required standards. The urban light rail transit (LRT) bogie frame used in the Greater Jakarta area is newly designed and manufactured by a commercial railway rolling stock manufacturer. The design lifetime of this newly designed bogie frame structure under various fatigue load conditions is verified experimentally by fatigue testing. Testing and evaluations were conducted following the EN 13749 standard and VDV recommendation. The fatigue test of the urban LRT bogie frame structure was carried out in the test hall of the BPPT Structural Strength Technology Center (B2TKS) using a combination of seven loadings. The bogie frame was subjected to two variable types of fatigue loads, namely driving in curves and passing points (switches), with 2,000,000 cycles, 4,000,000 cycles, and 6,000,000 cycles of fatigue loadings. The parameter measured on the bogie frame structure is the strain value during the test using a dynamic data logger. The stress values analyzed are the average stress and the stress amplitude and then plotted on the maximum and minimum stress curve. The bogie structure is inspected by the non-destructive test method in all areas of its welded joints. This inspection is carried out before and after the test to ensure whether there are cracks caused by fatigue loads. The results of the fatigue test on the bogie structure under the variable fatigue load conditions show that the maximum stress value of 91.71 MPa at 1,500,000 cycles, that occurs during the test, does not exceed the fatigue limit of the material, and there are no cracks in the structure after the test is carried out for up to 6,000,000 cycles.
- Open Access
- 17 July 2021
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 1 (1) , 31-40
Comprehensive Analysis of Minibuses Gravity Center: A Post-Production Review for Car Body Industry
The center of gravity (CoG) on the minibus is one of the fundamental parameters that affect the operation of the vehicle to maintain traffic safety. CoG greatly affects vehicle maneuverability due to load transfer between the front and rear wheels, such as when turning, braking, and accelerating. Therefore, this research was conducted to evaluate the operational safety of minibusses produced by the domestic car body industry. The case study was conducted on a minibus with a capacity of 30 passengers to be used in a mining area. Investigations on CoG were carried out based on the minibus specification data, especially the dimensions and forces acting on the wheels. Minibusses as test objects were categorized in two conditions, namely without passengers and with 30 passengers. The test results are expressed in a coordinate system (x, y, z) which represents the longitudinal, lateral, and vertical distances to the center of the front wheel axle. CoG coordinate values ”‹”‹without passengers are (2194.92; 7.11; 1327.97) mm and CoG coordinates with full passengers (30 people) are (2388.52; 13.04; 1251.72) mm. The test results show that the change in CoG at full load is not significant which indicates the minibus is safe when maneuvering under normal conditions.
- 17 July 2021
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 1 (1) , 31-40
Open AccessComprehensive Analysis of Minibuses Gravity Center: A Post-Production Review for Car Body Industry
The center of gravity (CoG) on the minibus is one of the fundamental parameters that affect the operation of the vehicle to maintain traffic safety. CoG greatly affects vehicle maneuverability due to load transfer between the front and rear wheels, such as when turning, braking, and accelerating. Therefore, this research was conducted to evaluate the operational safety of minibusses produced by the domestic car body industry. The case study was conducted on a minibus with a capacity of 30 passengers to be used in a mining area. Investigations on CoG were carried out based on the minibus specification data, especially the dimensions and forces acting on the wheels. Minibusses as test objects were categorized in two conditions, namely without passengers and with 30 passengers. The test results are expressed in a coordinate system (x, y, z) which represents the longitudinal, lateral, and vertical distances to the center of the front wheel axle. CoG coordinate values ”‹”‹without passengers are (2194.92; 7.11; 1327.97) mm and CoG coordinates with full passengers (30 people) are (2388.52; 13.04; 1251.72) mm. The test results show that the change in CoG at full load is not significant which indicates the minibus is safe when maneuvering under normal conditions.
- Open Access
- 24 December 2020
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 4 (1) , 36-43
Bogie Frame Structure Evaluation for Light-Rail Transit (LRT) Train: A Static Testing
A new bogie frame of Light-Rail Transit (LRT) is having its strength of structure verified with experimental static testing according to EN 13749 standards. Static testing of bogie frame structure of LRT is performed by using a combination of seven tensile and compression loads that comprise of operational loads (normal service) and over-loads (exceptional service). Measurement parameters of bogie frame are strain and deflection values. The strain and deflection values resulted at every step of the load test were measured and monitored to further be used as analytic data. This data is then compared to the stress data of finite element analysis to check its deviation value. Testing results show the maximum stress value is 81.48 MPa on operational load, meanwhile, for exceptional load case, maximum stress is 120.96 MPa and deflection value is 1.25 mm. The maximum stress value is still below yield strength of bogie frame material S 555J2 (ï³y=355 MPa). According to testing data, structure of bogie frame LRT fulfill as the acceptance criteria.
- 24 December 2020
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 4 (1) , 36-43
Open AccessBogie Frame Structure Evaluation for Light-Rail Transit (LRT) Train: A Static Testing
A new bogie frame of Light-Rail Transit (LRT) is having its strength of structure verified with experimental static testing according to EN 13749 standards. Static testing of bogie frame structure of LRT is performed by using a combination of seven tensile and compression loads that comprise of operational loads (normal service) and over-loads (exceptional service). Measurement parameters of bogie frame are strain and deflection values. The strain and deflection values resulted at every step of the load test were measured and monitored to further be used as analytic data. This data is then compared to the stress data of finite element analysis to check its deviation value. Testing results show the maximum stress value is 81.48 MPa on operational load, meanwhile, for exceptional load case, maximum stress is 120.96 MPa and deflection value is 1.25 mm. The maximum stress value is still below yield strength of bogie frame material S 555J2 (ï³y=355 MPa). According to testing data, structure of bogie frame LRT fulfill as the acceptance criteria.
- Open Access
- 3 August 2020
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 3 (3) , 104-114
Evaluation of Operational Loading of the Light-Rail Transit (LRT) in Capital Region, Indonesia
In 2015, the Indonesian government issued regulations to accelerate the implementation of integrated Light-Rail Transit (LRT) in the capital region and its surroundings. In order to ensure its operational safety, experimental work is required to test components”™ strength of the manufactured LRT structures. Following the JIS 7105 standard test method, the strain and deflection of the structures were measured by vertical load, compression, rotation, and three-point load support test. The critical area estimated in the railroad structure were conducted according to the finite element method, in which strain gauges are installed in areas where the stress concentration exceeds nominal pressure, namely notches, bends, and junction areas. The result shows that the maximum stress on the LRT train structure occurs at the door, where maximum compressive strain value is -1082 μe » -75.74 MPa on the left and the maximum tensile strain value is 597 μe » 41.79 MPa at the right door. The results of fatigue load analysis represent the average stress (σm) and voltage amplitude (σa) at the coordinate system located in the Søderberg triangle. Meanwhile, the camber value with the full vertical load still has a positive value of 3.03 mm, which indicates a safe limit.
- 3 August 2020
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 3 (3) , 104-114
Open AccessEvaluation of Operational Loading of the Light-Rail Transit (LRT) in Capital Region, Indonesia
In 2015, the Indonesian government issued regulations to accelerate the implementation of integrated Light-Rail Transit (LRT) in the capital region and its surroundings. In order to ensure its operational safety, experimental work is required to test components”™ strength of the manufactured LRT structures. Following the JIS 7105 standard test method, the strain and deflection of the structures were measured by vertical load, compression, rotation, and three-point load support test. The critical area estimated in the railroad structure were conducted according to the finite element method, in which strain gauges are installed in areas where the stress concentration exceeds nominal pressure, namely notches, bends, and junction areas. The result shows that the maximum stress on the LRT train structure occurs at the door, where maximum compressive strain value is -1082 μe » -75.74 MPa on the left and the maximum tensile strain value is 597 μe » 41.79 MPa at the right door. The results of fatigue load analysis represent the average stress (σm) and voltage amplitude (σa) at the coordinate system located in the Søderberg triangle. Meanwhile, the camber value with the full vertical load still has a positive value of 3.03 mm, which indicates a safe limit.