Zoey Huey
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zoey Huey has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
Chun-Sheng Jiang
Materials, Chemical, and Computational Science Directorate, National Renewable Energy Laboratory, Golden, Colorado 80401, USA
7 shared publications- Steven C. DeCaluwe
Colorado School of Mines
7 shared publications Sang-Don Han
National Renewable Energy Laboratory
6 shared publications- Bertrand J. Tremolet de Villers
National Renewable Energy Laboratory
5 shared publications - Chun-Sheng Jiang
National Renewable Energy Laboratory, Golden, Colorado 80401, United States
4 shared publications - Gerard Michael Carroll
National Renewable Energy Laboratory
3 shared publications
Latest Publications
- 5 December 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (3) , 2316-2326
Mechanical and electrical changes in electrochemically active polyimide binders for Li-ion batteries
A study on polyimide binder for Li ion batteries, showing active lithiation/delithiation with first cycle capacity loss, formation of dendrite-like morphology, elastic modulus increase, and overall electronic resistivity increase during lithiation.
- 5 December 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (3) , 2316-2326
Mechanical and electrical changes in electrochemically active polyimide binders for Li-ion batteries
A study on polyimide binder for Li ion batteries, showing active lithiation/delithiation with first cycle capacity loss, formation of dendrite-like morphology, elastic modulus increase, and overall electronic resistivity increase during lithiation.
- 9 October 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (44) , 30465-30475
Characterization of pitch carbon coating properties affecting the electrochemical behavior of silicon nanoparticle lithium-ion battery anodes
700 °C is the optimal heat treatment temperature for pitch-coated silicon electrodes. Both the amorphous carbon/pitch and silicon are active materials but store Li+ ions through different ion storage mechanisms and contribute to overall performance.
- 9 October 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (44) , 30465-30475
Characterization of pitch carbon coating properties affecting the electrochemical behavior of silicon nanoparticle lithium-ion battery anodes
700 °C is the optimal heat treatment temperature for pitch-coated silicon electrodes. Both the amorphous carbon/pitch and silicon are active materials but store Li+ ions through different ion storage mechanisms and contribute to overall performance.
- Open Access
Impacts of Curing-Induced Phase Segregation in Silicon Nanoparticle-Based Electrodes
We report the investigation of silicon nanoparticle composite anodes for Li-ion batteries, using a combination of two nm-scale atomic force microscopy-based techniques: scanning spreading resistance microscopy for electrical conduction mapping and contact resonance and force volume for elastic modulus mapping, along with scanning electron microscopy-based energy dispersion spectroscopy, nanoindentation, and electrochemical analysis. Thermally curing the composite anode—made of polyethylene oxide-treated Si nanoparticles, carbon black, and polyimide binder—reportedly improves the anode electrochemical performance significantly. This work demonstrates phase segregation resulting from thermal curing, where alternating bands of carbon and silicon active material are observed. This electrode morphology is retained after extensive cycling, where the electrical conduction of the carbon-rich bands remains relatively unchanged, but the mechanical modulus of the bands decreases distinctly. These electrical and mechanical factors may contribute to performance improvement, with carbon bands serving as a mechanical buffer for Si deformation and providing electrical conduction pathways. This work motivates future efforts to engineer similar morphologies for mitigating capacity loss in silicon electrodes.
Open AccessImpacts of Curing-Induced Phase Segregation in Silicon Nanoparticle-Based Electrodes
We report the investigation of silicon nanoparticle composite anodes for Li-ion batteries, using a combination of two nm-scale atomic force microscopy-based techniques: scanning spreading resistance microscopy for electrical conduction mapping and contact resonance and force volume for elastic modulus mapping, along with scanning electron microscopy-based energy dispersion spectroscopy, nanoindentation, and electrochemical analysis. Thermally curing the composite anode—made of polyethylene oxide-treated Si nanoparticles, carbon black, and polyimide binder—reportedly improves the anode electrochemical performance significantly. This work demonstrates phase segregation resulting from thermal curing, where alternating bands of carbon and silicon active material are observed. This electrode morphology is retained after extensive cycling, where the electrical conduction of the carbon-rich bands remains relatively unchanged, but the mechanical modulus of the bands decreases distinctly. These electrical and mechanical factors may contribute to performance improvement, with carbon bands serving as a mechanical buffer for Si deformation and providing electrical conduction pathways. This work motivates future efforts to engineer similar morphologies for mitigating capacity loss in silicon electrodes.
- Open Access
- 15 March 2024
- Published by Elsevier in SSRN Electronic Journal
Characterization of Pitch Carbon Coating Properties Affecting the Electrochemical Behavior of Silicon Nanoparticle Lithium-Ion Battery Anodes
Silicon is an exciting material for next-generation lithium-ion battery anodes, due to its high theoretical capacity and availability, but its widespread implementation has been limited by extensive volume changes during cycling that causes mechanical damage and limits cycle life. One approach to mitigating these deleterious effects while still maintaining silicon’s benefits is the addition of a pitch carbon coating to nanometer-sized silicon particles. Here, we present characterization of pitch-coated silicon electrodes without annealing and annealed at 700 °C and 1000 °C to determine the optimum temperature treatment, as well as pitch-only and silicon-only electrodes with and without annealing to elucidate the impacts of each component on early electrochemical behavior. Using Fourier transform infrared and Raman spectroscopies, atomic force and scanning spreading resistance microscopies, and electrochemical analysis, we find 700 °C to be the optimal annealing temperature, as amorphous carbon is created, which improves conductivity prior to cycling and facilitates ion storage during cycling that increases capacity. We also present in-situ Raman spectroscopy data demonstrating the heterogeneous aging that occurs across the electrode surface during cycling.
- 15 March 2024
- Published by Elsevier in SSRN Electronic Journal
Open AccessCharacterization of Pitch Carbon Coating Properties Affecting the Electrochemical Behavior of Silicon Nanoparticle Lithium-Ion Battery Anodes
Silicon is an exciting material for next-generation lithium-ion battery anodes, due to its high theoretical capacity and availability, but its widespread implementation has been limited by extensive volume changes during cycling that causes mechanical damage and limits cycle life. One approach to mitigating these deleterious effects while still maintaining silicon’s benefits is the addition of a pitch carbon coating to nanometer-sized silicon particles. Here, we present characterization of pitch-coated silicon electrodes without annealing and annealed at 700 °C and 1000 °C to determine the optimum temperature treatment, as well as pitch-only and silicon-only electrodes with and without annealing to elucidate the impacts of each component on early electrochemical behavior. Using Fourier transform infrared and Raman spectroscopies, atomic force and scanning spreading resistance microscopies, and electrochemical analysis, we find 700 °C to be the optimal annealing temperature, as amorphous carbon is created, which improves conductivity prior to cycling and facilitates ion storage during cycling that increases capacity. We also present in-situ Raman spectroscopy data demonstrating the heterogeneous aging that occurs across the electrode surface during cycling.
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (2) , 529
Control of Nanoparticle Dispersion, SEI Composition, and Electrode Morphology Enable Long Cycle Life in High Silicon Content, Nanoparticle-Based Composite Anodes for Lithium-Ion Batteries
Striking a balance between high theoretical capacity, Earth abundance, and compatibility with existing manufacturing infrastructure, silicon is one of the few materials that meets the requirements for a next-generation anode for rechargeable lithium-ion batteries. Due to complications with extreme volume changes during charging/discharging and reactive interfacial chemistries, however, the cycle-life of silicon-based composite anodes is unacceptable for broad use. Developing a majority silicon composite anode formulation that overcomes these challenges and is compatible with current industry manufacturing practices requires materials and chemical engineering solutions that account for both electrode morphology and interfacial chemistry. Here, we synthesize surface-functionalized silicon nanocrystals that enable a highly dispersed and homogeneous slurry that can easily be integrated into standard electrode fabrication process. We use this formulation to print a 76 wt. % silicon composite electrode. We show that the contents and the morphology of the silicon electrolyte interphase – a determining factor in the cycle life of silicon-based anodes – can be controlled with a post-synthetic thermal curing procedure. When paired against a capacity-matched lithium nickel manganese cobalt oxide LiNi0.8Mn0.1Co0.1O2 cathode, the cell retains 72% of its capacity through 1000 charge/discharge cycles while delivering an initial anode specific capacity of nearly 1000 mAh/g and an areal capacity of 2.55 mAh/cm2. Figure 1
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (2) , 529
Control of Nanoparticle Dispersion, SEI Composition, and Electrode Morphology Enable Long Cycle Life in High Silicon Content, Nanoparticle-Based Composite Anodes for Lithium-Ion Batteries
Striking a balance between high theoretical capacity, Earth abundance, and compatibility with existing manufacturing infrastructure, silicon is one of the few materials that meets the requirements for a next-generation anode for rechargeable lithium-ion batteries. Due to complications with extreme volume changes during charging/discharging and reactive interfacial chemistries, however, the cycle-life of silicon-based composite anodes is unacceptable for broad use. Developing a majority silicon composite anode formulation that overcomes these challenges and is compatible with current industry manufacturing practices requires materials and chemical engineering solutions that account for both electrode morphology and interfacial chemistry. Here, we synthesize surface-functionalized silicon nanocrystals that enable a highly dispersed and homogeneous slurry that can easily be integrated into standard electrode fabrication process. We use this formulation to print a 76 wt. % silicon composite electrode. We show that the contents and the morphology of the silicon electrolyte interphase – a determining factor in the cycle life of silicon-based anodes – can be controlled with a post-synthetic thermal curing procedure. When paired against a capacity-matched lithium nickel manganese cobalt oxide LiNi0.8Mn0.1Co0.1O2 cathode, the cell retains 72% of its capacity through 1000 charge/discharge cycles while delivering an initial anode specific capacity of nearly 1000 mAh/g and an areal capacity of 2.55 mAh/cm2. Figure 1
- Open Access
- 2 March 2023
- Published by Elsevier in Journal of Power Sources
- Vol. 564
Multi-modal characterization methods of solid-electrolyte interphase in silicon-graphite composite electrodes
- 2 March 2023
- Published by Elsevier in Journal of Power Sources
- Vol. 564
Open AccessMulti-modal characterization methods of solid-electrolyte interphase in silicon-graphite composite electrodes
- Open Access
- 3 February 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 11 (10) , 5257-5266
Control of nanoparticle dispersion, SEI composition, and electrode morphology enables long cycle life in high silicon content nanoparticle-based composite anodes for lithium-ion batteries
A 74 wt% silicon composite electrode delivers 1000 cycles with 74% capacity retention against NMC811 cathodes and a cell stack energy density of 212 W h kg−1 in a standard carbonate electrolyte with two simple chemical and process improvements.
- 3 February 2023
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 11 (10) , 5257-5266
Open AccessControl of nanoparticle dispersion, SEI composition, and electrode morphology enables long cycle life in high silicon content nanoparticle-based composite anodes for lithium-ion batteries
A 74 wt% silicon composite electrode delivers 1000 cycles with 74% capacity retention against NMC811 cathodes and a cell stack energy density of 212 W h kg−1 in a standard carbonate electrolyte with two simple chemical and process improvements.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Multi-Modal Characterization Methods of Solid Electrolyte Interphase in Silicon-Graphite Composite Electrodes
Composite silicon-graphite (Si-Gr) anodes can improve battery energy density, due to Si’s high gravimetric capacity, while mitigating mechanical degradation of the anode and associated solid-electrolyte interphase (SEI) caused by Si expansion during lithiation. Optimizing these anodes is challenging, partially due to difficulties characterizing the 3D SEI structure and its heterogeneity. We present multi-modal characterization of the SEI on Si-Gr anodes to understand SEI chemical composition and structure and how it relates to SEI properties. Results show discrepancies in elemental concentrations from X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), and energy-dispersive X-ray spectroscopy (EDS), due to varying information depths and lateral resolutions. By combining quantitative composition with spatial element mapping from scanning transmission electron microscopy (STEM), EDS, and electron energy loss spectroscopy (EELS), a holistic picture of the SEI emerges. We observe the bilayer SEI structure, a direct correlation between elemental Li and F, demonstrating that most of the Li exists as lithium fluoride (LiF), an inverse relationship between lithium carbonate and LiF concentration, providing direct insight into the chemistry of the SEI, and a proportional relationship between LiF content and maximum SEI resistivity, an important property for a passivating SEI, determined by scanning spreading resistance microscopy (SSRM).
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessMulti-Modal Characterization Methods of Solid Electrolyte Interphase in Silicon-Graphite Composite Electrodes
Composite silicon-graphite (Si-Gr) anodes can improve battery energy density, due to Si’s high gravimetric capacity, while mitigating mechanical degradation of the anode and associated solid-electrolyte interphase (SEI) caused by Si expansion during lithiation. Optimizing these anodes is challenging, partially due to difficulties characterizing the 3D SEI structure and its heterogeneity. We present multi-modal characterization of the SEI on Si-Gr anodes to understand SEI chemical composition and structure and how it relates to SEI properties. Results show discrepancies in elemental concentrations from X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), and energy-dispersive X-ray spectroscopy (EDS), due to varying information depths and lateral resolutions. By combining quantitative composition with spatial element mapping from scanning transmission electron microscopy (STEM), EDS, and electron energy loss spectroscopy (EELS), a holistic picture of the SEI emerges. We observe the bilayer SEI structure, a direct correlation between elemental Li and F, demonstrating that most of the Li exists as lithium fluoride (LiF), an inverse relationship between lithium carbonate and LiF concentration, providing direct insight into the chemistry of the SEI, and a proportional relationship between LiF content and maximum SEI resistivity, an important property for a passivating SEI, determined by scanning spreading resistance microscopy (SSRM).
- 30 May 2021
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2021-01 (2) , 113
Three-Dimensional Mapping of Cycling Changes in Silicon-Graphite Composite Anodes Via Scanning Probe Microscopy
Silicon (Si) anodes have the potential to greatly improve the energy density of lithium-ion batteries due to the greater specific capacity of Si relative to standard graphite (Gr) anodes (1). However, Si anode implementation is limited by issues such as volumetric expansion during cycling and an unstable solid-electrolyte interphase (SEI). Composite anodes with Si and Gr particles can increase capacity while mitigating Si anode degradation. However, these electrodes can be challenging to characterize (and therefore optimize) due to their multiple components, heterogeneous surfaces, and the complex processes occurring there. Scanning spreading resistance microscopy (SSRM) is a form of scanning probe microscopy that measures local resistivity in a sample. By removing material with the probe tip while measuring resistivity, three-dimensional resistivity maps can be determined (2). For Si-Gr composite anodes, the different resistivities of the electrode components (e.g., Si, Gr, carbon, and lithium polyacrylate binder) allows direct identification through SSRM. 3D nanoscale volumes can then be created for both the whole electrode and the individual components. This presentation will demonstrate 3D SSRM mapping of pristine and cycled anodes with three compositions – Si, Gr, and Si-Gr. By comparing changes in the morphology, thickness, and resistivity in the active material and SEI in each single-component electrode, the component distribution and evolution of the Si-Gr composite anode is better understood. SSRM results will be compared to chemical analysis techniques such as scanning transmission electron microscopy, energy dispersive x-ray spectroscopy, and electron energy loss spectroscopy to verify the component identification and to correlate chemical composition to resistivity. These data will then be correlated to electrochemical performance and used to further the development of Si-Gr electrodes with enhanced performance. W.-J. Zhang, Journal of Power Sources, 196, 13 (2011). C. Stetson, Z. Huey, A. Downard, Z. Li, B. To, A. Zakutayev, C. S. Jiang, M. M. Al-Jassim, D. P. Finegan, S. D. Han and S. C. DeCaluwe, Nano Lett (2020). Figure 1
- 30 May 2021
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2021-01 (2) , 113
Three-Dimensional Mapping of Cycling Changes in Silicon-Graphite Composite Anodes Via Scanning Probe Microscopy
Silicon (Si) anodes have the potential to greatly improve the energy density of lithium-ion batteries due to the greater specific capacity of Si relative to standard graphite (Gr) anodes (1). However, Si anode implementation is limited by issues such as volumetric expansion during cycling and an unstable solid-electrolyte interphase (SEI). Composite anodes with Si and Gr particles can increase capacity while mitigating Si anode degradation. However, these electrodes can be challenging to characterize (and therefore optimize) due to their multiple components, heterogeneous surfaces, and the complex processes occurring there. Scanning spreading resistance microscopy (SSRM) is a form of scanning probe microscopy that measures local resistivity in a sample. By removing material with the probe tip while measuring resistivity, three-dimensional resistivity maps can be determined (2). For Si-Gr composite anodes, the different resistivities of the electrode components (e.g., Si, Gr, carbon, and lithium polyacrylate binder) allows direct identification through SSRM. 3D nanoscale volumes can then be created for both the whole electrode and the individual components. This presentation will demonstrate 3D SSRM mapping of pristine and cycled anodes with three compositions – Si, Gr, and Si-Gr. By comparing changes in the morphology, thickness, and resistivity in the active material and SEI in each single-component electrode, the component distribution and evolution of the Si-Gr composite anode is better understood. SSRM results will be compared to chemical analysis techniques such as scanning transmission electron microscopy, energy dispersive x-ray spectroscopy, and electron energy loss spectroscopy to verify the component identification and to correlate chemical composition to resistivity. These data will then be correlated to electrochemical performance and used to further the development of Si-Gr electrodes with enhanced performance. W.-J. Zhang, Journal of Power Sources, 196, 13 (2011). C. Stetson, Z. Huey, A. Downard, Z. Li, B. To, A. Zakutayev, C. S. Jiang, M. M. Al-Jassim, D. P. Finegan, S. D. Han and S. C. DeCaluwe, Nano Lett (2020). Figure 1
- 30 May 2021
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2021-01 (2) , 125
(Invited) Spectroscopic and Microscopic Characterizations of Silicon-Electrolyte Interfacial Chemistry and Silicon-Based Electrode Aging Behaviors
Due to inherent properties of the silicon (Si)-electrolyte interphase (SEI)—complexity, high reactivity and continuous evolution—it remains a poorly understood topic in advanced Si-based Li-ion battery (LiB) research,1,2 and its detailed and real-time analysis is a great challenge. Vibrational spectroscopy, such as Raman and Fourier-transform infrared spectroscopy (FTIR), is one of the most important analytical tools for understanding and quantifying the interfacial chemical reactions. These techniques are used extensively by the battery community in their ex situ form, but developing in situ variants of these techniques and combing in situ analyses from both techniques can provide new insight and help to elucidate the mechanism of interfacial failure in battery systems. We have optimized in situ vibrational spectroscopy methods that show reproducible and stable performance over multiple cycles in terms of both electrochemistry and spectroscopy, which enables us to monitor the surface chemistry and evolution of the SEI. This is essential to gaining a better understanding of the electrochemical performance of Si-based LiBs.3-5 Further, the reactions leading to SEI growth and evolution in Si-based LiBs may be more comprehensively probed by monitoring changes in the gas and liquid phases. To this end, we are developing novel in situ gas chromatography (GC) techniques, which may be applied to both coin-type cells and larger-format pouch cells. Using custom cell designs, we track the evolution of electrolyte and degradation species in the gaseous and liquid6 phases at various stages of battery cycling. We achieve both qualitative identification and quantification through coupled mass-spectrometry (MS) and flame ionization detection (FID). This GC-MS-FID analysis complements our in situ vibrational spectroscopy studies, providing a true multi-modal and multi-phase approach to SEI analysis. Taken together, these studies can provide an in-depth understanding of the underlying chemistry and physics and mechanical explanation of various reactions/interactions within the SEI, thus enabling the rational design of electrolytes and electrodes to stabilize the SEI. Additionally, we have developed advanced techniques to assess the structural and electronic properties of Si-based composite electrodes. Comprehensive characterization of pristine and cycled composite electrode architectures is complicated by several inherent properties. During battery operation, Si-based composite electrodes experience localized lithiation and reaction rates due to heterogeneous conditions and distributions of electrode components. Further, (electro)chemical and structural properties continuously evolve during cycling. Finally, the nanoscale diameter of particles falls beneath the lateral and depth resolution of most laboratory-based instruments. To address these challenges, we have utilized scanning spreading resistance microscopy (SSRM) to image the three-dimensional nanostructure of composite anodes via contrast in the electronic properties of the distinct components.7 Specifically, Si-based composite anode components, such as SiOx nanoparticles, graphite, carbon black, and lithium polyacrylate binder, are all readily distinguished by their intrinsic electronic properties, with measured electronic resistivity closely matching known material properties. In combination with scanning electron microscopy/energy dispersive X-ray (SEM-EDX) and electron energy loss spectroscopy (EELS), we expect to compare the electrical, chemical and structural changes of Si-based composite electrodes before and after cycling. This can provide a fundamental understanding of localized degradation mechanisms, which informs our understanding of SEI formation and evolution. This technique may also be applied to assess heterogeneous aging within the electrode, and is more broadly applicable to other battery systems. In particular, it may be used to better understand particle dispersion, localized lithiation, electrolyte-electrode interphase formation/evolution, and degradation processes in composite electrodes for the development of next-generation batteries. References: Xu, C. Stetson, K. Wood, E. Sivonxay, C. Jiang, G. Teeter, S. Pylypenko, S.-D. Han, K. A. Persson, A. Burrell and A. Zakutayev, ACS Appl. Mater. Interfaces 2018, 10, 38558-38564. -D. Han,* K. N. Wood, C. Stetson, A. G. Norman, M. T. Brumbach, J. Coyle, Y. Xu, S. P. Harvey, G. Teeter, A. Zakutayev and A. K. Burrell, ACS Appl. Mater. Interfaces 2019, 11, 46993-47002. Ha, B. J. Tremolet de Villers, Z. Li, Y. Xu, P. Stradins, A. Zakutayev, A. Burrell and S.-D. Han,* J. Phys. Chem. Lett. 2020, 11, 286-291. Yin, R. Pekarek, C. Stetson, M. Schnabel, E. Arca, S. Harvey, B. Tremolet de Villers, S.-D. Han, S. DeCaluwe, G. Teeter, C. Ban and N. Neale, 2021, under revision. J. Tremolet de Villers, J. Yang, S.-M. Bak and S.-D. Han,* 2021, under revision. Ha, C. Stetson, S. P. Harvey, G. Teeter, B. J. Tremolet de Villers, C.-S. Jiang, M. Schnabel, P. Stradins, A. Burrell and S.-D. Han,* ACS Appl. Mater. Interfaces 2020, 12, 49563-49573. C. Stetson, Z. Huey, A. Downard, Z. Li, B. To, A. Zakutayev, C.-S. Jiang, M. Al-Jassim, D. P. Finegan, S.-D. Han* and S. C. DeCaluwe, Nano Lett. 2020, 20, 8081-8088.
- 30 May 2021
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2021-01 (2) , 125
(Invited) Spectroscopic and Microscopic Characterizations of Silicon-Electrolyte Interfacial Chemistry and Silicon-Based Electrode Aging Behaviors
Due to inherent properties of the silicon (Si)-electrolyte interphase (SEI)—complexity, high reactivity and continuous evolution—it remains a poorly understood topic in advanced Si-based Li-ion battery (LiB) research,1,2 and its detailed and real-time analysis is a great challenge. Vibrational spectroscopy, such as Raman and Fourier-transform infrared spectroscopy (FTIR), is one of the most important analytical tools for understanding and quantifying the interfacial chemical reactions. These techniques are used extensively by the battery community in their ex situ form, but developing in situ variants of these techniques and combing in situ analyses from both techniques can provide new insight and help to elucidate the mechanism of interfacial failure in battery systems. We have optimized in situ vibrational spectroscopy methods that show reproducible and stable performance over multiple cycles in terms of both electrochemistry and spectroscopy, which enables us to monitor the surface chemistry and evolution of the SEI. This is essential to gaining a better understanding of the electrochemical performance of Si-based LiBs.3-5 Further, the reactions leading to SEI growth and evolution in Si-based LiBs may be more comprehensively probed by monitoring changes in the gas and liquid phases. To this end, we are developing novel in situ gas chromatography (GC) techniques, which may be applied to both coin-type cells and larger-format pouch cells. Using custom cell designs, we track the evolution of electrolyte and degradation species in the gaseous and liquid6 phases at various stages of battery cycling. We achieve both qualitative identification and quantification through coupled mass-spectrometry (MS) and flame ionization detection (FID). This GC-MS-FID analysis complements our in situ vibrational spectroscopy studies, providing a true multi-modal and multi-phase approach to SEI analysis. Taken together, these studies can provide an in-depth understanding of the underlying chemistry and physics and mechanical explanation of various reactions/interactions within the SEI, thus enabling the rational design of electrolytes and electrodes to stabilize the SEI. Additionally, we have developed advanced techniques to assess the structural and electronic properties of Si-based composite electrodes. Comprehensive characterization of pristine and cycled composite electrode architectures is complicated by several inherent properties. During battery operation, Si-based composite electrodes experience localized lithiation and reaction rates due to heterogeneous conditions and distributions of electrode components. Further, (electro)chemical and structural properties continuously evolve during cycling. Finally, the nanoscale diameter of particles falls beneath the lateral and depth resolution of most laboratory-based instruments. To address these challenges, we have utilized scanning spreading resistance microscopy (SSRM) to image the three-dimensional nanostructure of composite anodes via contrast in the electronic properties of the distinct components.7 Specifically, Si-based composite anode components, such as SiOx nanoparticles, graphite, carbon black, and lithium polyacrylate binder, are all readily distinguished by their intrinsic electronic properties, with measured electronic resistivity closely matching known material properties. In combination with scanning electron microscopy/energy dispersive X-ray (SEM-EDX) and electron energy loss spectroscopy (EELS), we expect to compare the electrical, chemical and structural changes of Si-based composite electrodes before and after cycling. This can provide a fundamental understanding of localized degradation mechanisms, which informs our understanding of SEI formation and evolution. This technique may also be applied to assess heterogeneous aging within the electrode, and is more broadly applicable to other battery systems. In particular, it may be used to better understand particle dispersion, localized lithiation, electrolyte-electrode interphase formation/evolution, and degradation processes in composite electrodes for the development of next-generation batteries. References: Xu, C. Stetson, K. Wood, E. Sivonxay, C. Jiang, G. Teeter, S. Pylypenko, S.-D. Han, K. A. Persson, A. Burrell and A. Zakutayev, ACS Appl. Mater. Interfaces 2018, 10, 38558-38564. -D. Han,* K. N. Wood, C. Stetson, A. G. Norman, M. T. Brumbach, J. Coyle, Y. Xu, S. P. Harvey, G. Teeter, A. Zakutayev and A. K. Burrell, ACS Appl. Mater. Interfaces 2019, 11, 46993-47002. Ha, B. J. Tremolet de Villers, Z. Li, Y. Xu, P. Stradins, A. Zakutayev, A. Burrell and S.-D. Han,* J. Phys. Chem. Lett. 2020, 11, 286-291. Yin, R. Pekarek, C. Stetson, M. Schnabel, E. Arca, S. Harvey, B. Tremolet de Villers, S.-D. Han, S. DeCaluwe, G. Teeter, C. Ban and N. Neale, 2021, under revision. J. Tremolet de Villers, J. Yang, S.-M. Bak and S.-D. Han,* 2021, under revision. Ha, C. Stetson, S. P. Harvey, G. Teeter, B. J. Tremolet de Villers, C.-S. Jiang, M. Schnabel, P. Stradins, A. Burrell and S.-D. Han,* ACS Appl. Mater. Interfaces 2020, 12, 49563-49573. C. Stetson, Z. Huey, A. Downard, Z. Li, B. To, A. Zakutayev, C.-S. Jiang, M. Al-Jassim, D. P. Finegan, S.-D. Han* and S. C. DeCaluwe, Nano Lett. 2020, 20, 8081-8088.