YCYechuan Chen

Yechuan Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yechuan Chen has a total of 74 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Surface morphology and oxide phases of Cu pads in vias under thermal annealing in air

    by Ranjitha Kumarapuram Hariharalakshmanan, Weichang Lin, Nick Polomoff, Roy Yu, Katsuyuki Sakuma, Yechuan Chen, Chao Yang, Katharine Dovidenko, James Lu, Toh-Ming Lu, et al.

    Thermal annealing of Cu, including oxidation and grain growth, plays a crucial role in the reliability performance of microelectronic devices. We present an experimental analysis of Cu oxide growth in dielectric-confined Cu pads in vias, essential for the development of a reliable Cu/oxide hybrid bonding process. Thermal oxidation of Cu pads grown by electroplating and processed by dual damascene was performed at a fixed annealing temperature (Ta) from 200 to 350 °C for 30 min under ambient air. As the temperature increases, the Cu pad expands and bulges above the dielectric surface. The surface morphology and roughness of Cu pad were examined by atomic force microscopy. The evolution of Cu oxide phases versus Ta was examined by Raman spectroscopy. At low Ta, the Cu2O phase dominates. As Ta increases, the CuO phase appears at 250 °C and coexists with the Cu2O phase. The energy dispersive x-ray spectroscopy shows that Cu oxide phases exist in the bulged-out Cu pad and can be detached from the unoxidized part of the Cu pad beneath the dielectric surface. The focused ion beam cross sections of Cu pads show a boundary region with gaps and void between oxidized Cu and unoxidized Cu pads. This understanding is relevant for the reliability of hybrid bonding in microelectronic Cu interconnects.

  • Open Access

    X-ray Photoelectron Spectroscopy Analysis of Nafion-Containing Samples: Pitfalls, Protocols, and Perceptions of Physicochemical Properties

    by Michael J. Dzara, Kateryna Artyushkova, Jayson Foster, Hamideh Eskandari, Yechuan Chen, Scott A. Mauger, Plamen Atanassov, Kunal Karan, Svitlana Pylypenko

    X-ray photoelectron spectroscopy (XPS) is one of the most common techniques used to analyze the surface composition of catalysts and support materials used in polymer electrolyte membrane (PEM) fuel cells and electrolyzers, providing important insights for further improvement of their properties. Characterization of catalyst layers (CLs) is more challenging, which can be at least partially attributed to the instability of ionomer materials such as Nafion during measurements. This work explores the stability of Nafion during XPS measurements, illuminating and addressing Nafion degradation concerns. The extent of Nafion damage as a function of XPS instrumentation, measurement conditions, and sample properties was evaluated across multiple instruments. Results revealed that significant Nafion damage to the ion-conducting sulfonic acid species (>50% loss in sulfur signal) may occur in a relatively short time frame (tens of minutes) depending on the exact nature of the sample and XPS instrument. This motivated the development and validation of a multipoint XPS data acquisition protocol that minimizes Nafion damage, resulting in reliable data acquisition by avoiding significant artifacts from Nafion instability. The developed protocol was then used to analyze both thin film ionomer samples and Pt/C-based CLs. Comparison of PEM fuel cell CLs to Nafion thin films revealed several changes in Nafion spectral features attributed to charge transfer due to interaction with conductive catalyst and support species. This study provides a method to reliably characterize ionomer-containing samples, facilitating fundamental studies of the catalyst-ionomer interface and more applied investigations of structure-processing-performance correlations in PEM fuel cell and electrolyzer CLs.


  • Top Cited Papers

    Catalysts by pyrolysis: Transforming metal-organic frameworks (MOFs) precursors into metal-nitrogen-carbon (M-N-C) materials

    by Ying Huang, Yechuan Chen, Mingjie Xu, Alvin Ly, Albert Gili, Eamonn Murphy, Tristan Asset, Yuanchao Liu, Vincent De Andrade, Carlo U. Segre, et al.


  • Pyrolysis of Metal Organic Frameworks (MOF): Transformations Leading to Formation of Transition Metal-Nitrogen-Carbon Catalysts

    by Ying Huang, Yechuan Chen, Mingjie Xu, Albert Gili de Villasante, Tristan Asset, Yuanchao Liu, Alvin Ly, Xiaoqing Pan, Plamen Atanassov, Iryna V. Zenyuk

    Metal Organic Framework (MOF) materials link inorganic and organic units by strong bonds, forming porous structures. Pyrolysis consists of heat treatment in inert or reductive atmosphere. Pyrolysis of MOFs, which uses MOFs as a template, is a promising way to synthesize carbon-based oxygen reduction reaction (ORR) catalysts. The size, shape and composition of the pyrolysis product is controllable by choosing MOF-based precursors and tuning the pyrolysis parameters. Two MOFs that are frequently used in the ORR catalysis are selected in this study: ZIF-8 and ZIF-67, both of which can be synthesized under ambient temperature and pressure. Co-based ZIF-67 is considered as a good precursor to highly active Co-N-C ORR catalysts due to its high content of nitrogen and cobalt. Zn-based ZIF-8 has isostructural structure to ZIF-67, but contains Zn instead of Co. Currently, pyrolysis process is highly empirical, where process parameters are optimized via trial-and-error. In this study we aim to demystify pyrolysis process and provide understanding on transformation of ZIF-based precursors during pyrolysis. Our team has investigated the pyrolytic synthesis of both ZIF-8 and ZIF-67 via in situ STEM, EDS and XRD and used electrochemical techniques to assess pyrolyzed materials activity towards ORR. The structures of both MOFs shrunk in size after pyrolysis to 1050 °C under high-vacuum environment, indicating that material evaporation and decomposition happened. However, the structure of the ZIF-8 remained, while that of ZIF-67 did not. The product of pyrolyzing ZIF-8 contains graphitic planes along with amorphous carbon phases. On the other hand, metal carbide covered by graphitized shell was formed during the pyrolysis of ZIF-67. Ex situ XPS was conducted on the precursor, product of pyrolysis and the product after acid etching. The nitrogen contained in the product of pyrolyzing ZIF-8 will not be removed after acid etching. A low content of nitrogen was observed on the surface and few nanometers beneath the surface of the pyrolysis product of ZIF-67. Most of the cobalt that remained after pyrolyzing the Co-based ZIF-67 will be removed by acid-etching. The degree of graphitization is the main difference between the process of pyrolyzing ZIF-8 and ZIF-67. The metal that remained at high temperature (1050 °C) might have catalyzed the graphitization process and thus destroyed the structure. The electrochemical activity of the pyrolysis products of ZIF-8 and ZIF-67 before and after acid etching was assessed with a rotating ring disk electrode setup. The halfwave potential of ZIF-67 was very low (~0.6 V), whereas the halfwave potential of ZIF-67 was higher, at 0.7 V. ZIF-67 showed very low surface area, as the structure of the MOF was not preserved during synthesis, whereas ZIF-8 did preserve structure and featured high electrochemical surface area. Figure. XPS, STEM characterization and electrochemical activity assessment. (a) XPS survey results of ZIF-8, its pyrolysis product, and the product after acid etching. ArE: Ar Etching. (b) STEM images of ZIF-8 after pyrolysis. (c) XPS survey results of ZIF-67, its pyrolysis product, and the product after acid etching. ArE: Ar Etching. (d) STEM images of ZIF-67 when pyrolyzing to 1050 °C. (e) ring current density and (f) disk current density in O2-saturated electrolyte. Red solid: ZIF-8 pyrolyzed to 975 under H2 atmosphere. Red dash: ZIF-8 pyrolyzed to 975 under H2 atmosphere with acid etching. Black solid: ZIF-67 pyrolyzed to 975 °C under H2 atmosphere. Black dash: ZIF-67 pyrolyzed to 975 °C under H2 atmosphere with acid etching. Figure 1


  • Catalyst Degradation in Polymer Electrolyte Fuel Cells with Multi-Modal Techniques: Understanding Phenomena Under Varied Gas and Relative Humidity

    by Kaustubh Khedekar, Morteza Rezaei Talarposhti, Lei Cheng, Saravanan Kuppan, Andrea Perego, Yechuan Chen, Michael Metzger, Sarah Stewart, Plamen Atanassov, Nobumichi Tamura, et al.

    For widespread commercialization of polymer electrolyte fuel cells (PEFCs), cost and durability need to be addressed. Reduction in cost should not negatively affect PEFC durability and performance. At high volume production, platinum (Pt) electro catalyst contributes to 41% of the total fuel cell stack cost for light duty vehicles. This cost contribution increases to 53% for middle and heavy-duty vehicles. When membrane electrode assemblies (MEAs) are designed for durability, this cost will increase further. A complex balance exists between cost, performance and durability. With smaller nanoparticle size better Pt dispersion is achieved which gives improved performance and reduces Pt loading and cost. But this negatively affects durability, as smaller nanoparticles have higher surface energy which causes faster electrocatalyst degradation1. During an actual drive cycle, PEFCs need to operate over a wide range of operating conditions such as temperature (-40C to 120C), potential (0V to 1.5V) and relative humidity which can further accelerate Pt dissolution Under load cycling during typical drive cycle, repeated oxidation and reduction of Pt surface leads to Pt dissolution2. Dissolved Pt ions redeposit on nearby nanoparticles effectively increasing their particle size2. This electrochemical surface area (ECSA) loss via increase in particle size is well known as Ostwald ripening. Some Pt ions are reduced in the electrolyte membrane by crossover hydrogen which leads to formation of a Pt band, usually at the membrane and cathode catalyst layer interface3. At > 1V, carbon corrosion can lead to Pt detachment2. This can happen during start-up/shut down cycles when anode is exposed to hydrogen and air. Such degradation mechanisms need to be studied systematically with effect of operating conditions like gas flow rates, temperature and relative humidity under dynamic load cycling. In this study, we investigate the effect of cathode gas environment and gas flow rates on Pt particle size during aging experiment. A DOE adopted accelerated stress test (AST) protocol simulating the drive cycle operating conditions is used. It consists of a 0.6 V – 0.95 V square wave with 3s hold time at each potential. In situ electrochemical characterization at regular stages is used to identify ECSA loss trends and polarization performance. Figure 1 shows normalized ECSA loss for the four cells cycled in different environments during catalyst AST. Measurements were taken beginning of life (BOL), after 1,000, 5,000, 15,000 and 30,000 cycles. We observed that the cell that was cycled in N2 and 100 % RH degraded the most , having 25 % of ECSA left after 30,000 cycles compared to BOL. Electrochemical measurements are supplemented by detailed post-mortem ex-situ x-ray characterization by using micro x-ray fluorescence, x- ray computed tomography and micro x-ray diffraction, SEM-EDS. 1cm2 active areas of the catalyst layer at the inlet, middle and outlet of the flow field were mapped using micro x-ray diffraction to understand Pt particle size distribution under land/channel. Catalyst layer loading before and after the AST were confirmed using micro x-ray fluorescence. References (1) Cherevko, S.; Kulyk, N.; Mayrhofer, K. J. J. Durability of Platinum-Based Fuel Cell Electrocatalysts: Dissolution of Bulk and Nanoscale Platinum. Nano Energy 2016, 29, 275–298. https://doi.org/10.1016/j.nanoen.2016.03.005. (2) Meier, J. C.; Galeano, C.; Katsounaros, I.; Witte, J.; Bongard, H. J.; Topalov, A. A.; Baldizzone, C.; Mezzavilla, S.; Schüth, F.; Mayrhofer, K. J. J. Design Criteria for Stable Pt/C Fuel Cell Catalysts. Beilstein J. Nanotechnol. 2014, 5 (1), 44–67. https://doi.org/10.3762/bjnano.5.5. (3) Zhang, J.; Litteer, B. A.; Gu, W.; Liu, H.; Gasteiger, H. A. Effect of Hydrogen and Oxygen Partial Pressure on Pt Precipitation within the Membrane of PEMFCs. J. Electrochem. Soc. 2007, 154 (10), B1006. https://doi.org/10.1149/1.2764240. Figure 1

  • Electrocatalysts Based on Cobalt- and Nitrogen-Doped Nanocarbon Composites for Oxygen Reduction Reaction and Anion Exchange Membrane Fuel Cells

    by Jaana Lilloja, Elo Kibena-Poldsepp, Ave Sarapuu, Mounika Kodali, Yechuan Chen, Tristan Asset, Maike Käärik, Maido Merisalu, Päärn Paiste, Jaan Aruväli, et al.

    With an increasing energy demand, there is a need for renewable energy conversion devices. Among the possible options are low temperature polymer electrolyte fuel cells, in which electrocatalysts play vital roles, especially on the cathode, where the oxygen reduction reaction (ORR) occurs. The most efficient electrocatalysts for the ORR are based on noble metals, mainly platinum, which however have various disadvantages including their high price and scarcity. As a replacement, different transition metal-nitrogen-carbon (M−N−C) catalyst materials have shown great promise.1,2 Herein, a composite of nanocarbons, namely carbide-derived carbon/carbon nanotube (CDC/CNT), is employed as a support to produce the M−N−C type of catalysts. This composite offers a novel catalyst structure in which both micro- and mesopores are present that can be beneficial for the anion exchange membrane fuel cell (AEMFC) application. The doping was done via pyrolysis at 800 °C in the presence of a cobalt salt and a nitrogen precursor (either dicyandiamide, urea or melamine).3 The catalysts were characterized using different physico-chemical methods (e.g. SEM, TEM, XPS, XRD, Raman spectroscopy, and N2 adsorption), which proved the success of doping as well as the feasible micro- and mesoporous structure with defects present. Both the RDE and RRDE methods were employed for the electrochemical testing and in alkaline medium all three catalyst materials exhibited similar and good electrocatalytic activity for the ORR. The half-wave potential for ORR of Co-N-CDC/CNT catalysts was close to that of a Pt/C catalyst (Figure 1, left). The possible application of the Co-N-CDC/CNT material was tested out by employing it as a cathode catalyst in AEMFC. The Co-N-CDC/CNT catalyst together with a novel HMT-PMBI4 membrane exhibited excellent performance with peak power density of 577 mW cm–2, which was significantly higher than that obtained with a Pt/C cathode (Figure 1, right). This shows that the Co-N-CDC/CNT materials are promising cathode catalysts for the AEMFC application.3 References A. Sarapuu, E. Kibena-Põldsepp, M. Borghei, and K. Tammeveski, J. Mater. Chem. A, 6, 776-804 (2018). G. Wu, A. Santandreu, W. Kellogg, S. Gupta, O. Ogoke, H. Zhang, H. L. Wang, and L. Dai, Nano Energy, 29, 83−110 (2016). J. Lilloja, E. Kibena-Põldsepp, A. Sarapuu, M. Kodali, Y. Chen, T. Asset, M. Käärik, M. Merisalu, P. Paiste, J. Aruväli, A. Treshchalov, M. Rähn, J. Leis, V. Sammelselg, S. Holdcroft, P. Atanassov, and K. Tammeveski, ACS Appl. Energy Mater., 2020, (DOI: 10.1021/acsaem.0c00381) A. G. Wright, J. T. Fan, B. Britton, T. Weissbach, H. F. Lee, E. A. Kitching, T. J. Peckham, and S. Holdcroft, Energy Environ. Sci., 9, 2130-2142 (2016). Figure 1

  • Understanding Pyrolysis: Operandoand in Situcharacterization of Morphology and Composition Changes during Synthesis of M-N-C Electrocatalysts

    by Yechuan Chen, Ying Huang, Tristan Asset, Devashish Shashikant Kulkarni, Mingjie Xu, Peter Tieu, Xiaoqing Pan, Iryna V. Zenyuk, Plamen Atanassov

    Transition metal-nitrogen-carbon (M-N-C) materials have been continuously reported to be one of most promising platinum group metal-free (PGM-free) catalysts for oxygen reduction reaction (ORR)/cathode in low-temperature polymer electrolyte fuel cells (PEFC) and other emerging areas (such as carbon dioxide reduction reaction and nitrogen reduction reaction). They are usually obtained through pyrolysis of low molecular weight (organic) or polymetric precursors. The pyrolysis consists of heat treatment in inert (or reductive) atmosphere. Through the decades of practice, this pyrolysis process has been optimized intuitively and empirically with little-to-no knowledge of the explicit sequence of transformations. Morphological, structural, interfacial and chemical changes during pyrolysis enable the emergence of the new material with atomically dispersed transition metal ions. These ions are incorporated in the graphene-like carbonaceous matrix, doped with nitrogen and forming various Fe-Nxcatalytically active sites. Often, a secondary pyrolysis process is being carries out, after the completion of the initial one, resulting in better defined, and in many cases, more active and stable catalysts (a.k.a. “re-pyrolysis”). Our team have investigated both stages of the pyrolytic synthesis via in situXPS, TEM, EDS, XRD and nano- and micro-XCT methods in two separate studies dedicated to (i) pyrolysis of charge-transfer organic salt (nicarbazin) when mixed with silica template (a.k.a. “sacrificial support method” of M-N-C catalyst synthesis) and (ii) re-pyrolysis (secondary, “purification” pyrolysis) of the M-N-C material as a path to obtain atomically dispersed PGM-free catalyst. During the first pyrolysis we have observed for the first time the explicit melting of the precursor (at exact thermal signature), wetting of the hard template and followed major transformation in morphology: pore structure evolution, initial graphitization, metal and metal carbide phase formation, secondary graphitization templated on the transition metal nanoparticles and secondary micro-pores formation. All these observations have been interpreted through cross-referencing tomography, crystallography, microscopy and spectroscopy in situdata streams. We established that the re-pyrolysis of M-N-C materials could result in the amorphization of carbon, the rearrangement of multitudinous N-containing moieties, and increased content and a more uniform distribution of Fe-Nxsites, yet without major morphology changes in carbonaceous framework. In summary, the re-pyrolysis has multiple advantages and is recommended for all M-N-C electrocatalysts, no matter what precursors and parameters are set for their synthesis.


  • In Situ Characterization of Fe-N-C Electrocatalysts Synthesis By XPS and XRD

    by Yechuan Chen, Tristan Asset, Mounika Kodali, Kateryna Artyushkova, Plamen Atanassov

    As one of the most promising candidates to replace Pt-based electrocatalyst for oxygen reduction reaction in fuel cell, Metal-Nitrogen-Carbon (M-N-C) catalysts, especially Iron-Nitrogen-Carbon (Fe-N-C) materials, have attracted massive research interests in recent years. Typically, there are three main categories of synthesis approaches for Fe-N-C electrocatalyst, based on what chemicals are used as iron and nitrogen precursors: macrocyclic iron complexes, metal-organic frameworks, and various heterocyclic compounds. Despite these different approaches, it is found that numerous purified preliminary Fe-N-C products need further heat treatment to achieve better electrocatalysis performance. However, the reason why heat treatment is efficient, as well as the best parameters such as atmosphere, time and temperature, are still unclear and require intensive characterization for elucidation. Here, we report in situ XPS for the investigation how carbon environment and nitrogen moieties change, in addition to in situ XRD, on a specific atomic-dispersed Fe-N-C material (made from nicarbazin via sacrificial support method[1]) during high temperature heat treatment. Figure 1 shows the change of surface contents via XPS C 1s and N 1s under ultra-high vacuum. It is found by rising the temperature from room to 750 °C, the graphitic C with a characteristic peak around 284.5 eV decreases from ~50 atomic % to ~20 %, resulting in a more fragmented carbon structure, while sp3 carbon and nitrogen-carbon have an obvious increase. After flash heating to 950 °C (the typical point used in 2nd heat treatment for this electrocatalyst synthesis) and followed cooling back to 150 °C, there is no reversibility of graphitic carbon. For N 1s shown in Figure 1B, comparing initial 150 °C and final 150 °C after cooling, it is found that pyridinic-N content drops from ~20 atomic % to 15%, and pyrrolic-N decreases from ~40 % to 30 % respectively. Meanwhile, metallic/amine nitrogen increases from ~10% to ~15% while graphitic-N/N+ grows from ~7 % to 20 %, resulting in a more efficient Fe-Nx bonding and surface ionic conduction. In addition, in situ XRD shows that there is no obvious crystalline formed during high temperature treatment, indicating that there is no agglomeration of iron particles. These in situ XPS and XRD results elucidate that extra heat treatment of Fe-N-C electrocatalyst after preliminary synthesis and purification is an essential procedure and can improve the electrochemical performance efficiently. [1] M. J. Workman, M. Dzara, C. Ngo, S. Pylypenko, A. Serov, S. McKinney, J. Gordon, P. Atanassov, K. Artyushkova, J. Power Sources 2017, 348, 30-39. Figure 1

  • Insights Onto the Active Sites and Reactivity of Metal-Doped Carbonaceous Electrocatalysts for the CO2 Reduction Reaction

    by Tristan Asset, Ivana Matanovic, Yechuan Chen, Kateryna Artyushkova, Plamen Atanassov

    The CO2 valorization, i.e. its use in various electrochemical processes resulting in the production of carbon-based fuels and value-added chemicals, is of critical importance. Hence, the CO2 reduction reaction (CO2RR) has been widely investigated on electrocatalysts ranging from Cu-based nanostructures to carbonaceous materials. The latter often consist of carbon with atomically dispersed nitrogen and metals atoms (M-N-C, see Figure 1c). Such materials have been discussed in the literature, mostly using Fe as the metallic element 1 (but also Mn, Ni, Co and Cu 2–4), thus providing insights onto this family of electrocatalysts reactivity. But most of those electrocatalysts, as a result of their synthesis process, presents unwanted metallic contaminants 2. Here, we synthesized M-N-C electrocatalysts (with M = Cr, Mn, Fe, Co, Ni, Cu & Zn) using the sacrificial support method, that resulted into non-contaminated M-N-C materials. We then combined electrochemistry and density functional theory to separate the electrocatalysts in several categories, based on their COads binding strength. The strong COads binder electrocatalysts (e.g. Cr, Mn and Fe-N-C) achieved a Faradaic efficiency up to 50% at 0.35 V vs. RHE (at pH = 7.5, in 0.1 M phosphate buffer), as well as a metal-free electrocatalyst synthesized by the same method. This phenomenon was further investigated using near-ambient pressure XPS, which evidenced that the preferential adsorption site for CO2 was dependent of the metallic element nature: for Fe-N-C, the CO2 preferentially adsorb on pyridinic and hydrogenated (pyrrolic) nitrogen moieties (see Figure 1), hence evidencing the key role played by said moieties in the reactivity of the M-N-C electrocatalysts for the CO2RR. (1) Varela, A. S.; Ju, W.; Strasser, P. Adv. Energy Mater. 2018, 8 (30), 1–35; (2) Ju, W.; Bagger, A.; Hao, G. P.; Varela, A. S.; Sinev, I.; Bon, V.; Roldan Cuenya, B.; Kaskel, S.; Rossmeisl, J.; Strasser, P. Nat. Commun. 2017, 8 (1), 1–9; (3) Varela, A. S.; Ranjbar Sahraie, N.; Steinberg, J.; Ju, W.; Oh, H. S.; Strasser, P. Angew. Chemie - Int. Ed. 2015, 54 (37), 10758–10762; (4) Hu, X. M.; Hval, H. H.; Bjerglund, E. T.; Dalgaard, K. J.; Madsen, M. R.; Pohl, M. M.; Welter, E.; Lamagni, P.; Buhl, K. B.; Bremholm, M.; Beller, M.; Pedersen, S. U.; Skrydstrup, T.; Daasbjerg, K. ACS Catal. 2018, 8 (7), 6255–6264. Figure 1

  • Role of Protons on Activity and Selectivity of Fe-N-C Electroctatalysts for Oxygen Reduction Reaction

    by Yechuan Chen, Tristan Asset, Ivana Matanovic, Kateryna Artyushkova, Plamen Atanassov

    As one of the most promising candidates to replace Pt-based electrocatalysts for oxygen reduction reaction (ORR) in proton exchange membrane fuel cell (PEMFC), iron-nitrogen-carbon (Fe-N-C) materials have attracted tremendous research interests in recent years. Different from platinum-group-metal (PGM) catalysts, Fe-N-C have several categories of active sites: Fe-Nx has 4-electron pathway; pyrrolic-N and hydrogenated pyridinic-N can partially reduce oxygen into peroxide; pyridinic-N can reduce peroxide into water. Due to this complicated environment and numerous synthesis approaches from various precursors, the electrocatalysis mechanism of Fe-N-C still needs intensive investigation. Here we report the proton independence/dependence of rate-determining step (RDS) for a specific Fe-N-C catalyst via kinetic isotope effect (KIE), in addition to the activity inhibition of proton-involved N active sites via two molecular inhibitors. It is found that Fe-N-C can behave proton independent RDS like conventional Pt electrocatalyst in kinetic-controlled region, but it undergoes proton-coupled electron transfer in mass transport-controlled region, probably attributed to N active sites. It is also discovered that two molecules, tris(hydroxymethyl)aminomethane and etidronic acid, can inhibit and transform two categories of N active sites respectively: tris can effectively poison Fe-Nx active sites and pyridinic-N, resulting in obvious increase of peroxide yielding and drop of half-wave potential; etridonic acid can readily inhibit pyrrolic-N as well as hydrogenated pyridinic-N but no damage to Fe-Nx active sites, leading to decrease of peroxide yielding and no change of half-wave potentials. These results elucidate that Fe-N-C catalysts could, in principle, compete with Pt-based ORR catalysts through careful optimization of structure and morphology. Figure 1