Kenny Huynh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kenny Huynh has a total of 114 co-authors. Here are the top co-authors by number of shared publications:
- Mark S. Goorsky
University of California, Los Angeles
25 shared publications Michael Evan Liao
University of California, Los Angeles
13 shared publications- Michael E. Liao
University of California, Los Angeles
10 shared publications Brandon Carson
University of California, Los Angeles
5 shared publicationsYekan Wang
Materials Science and Engineering, University of California, Los Angeles, Los Angeles, California 90095, United States
5 shared publicationsKarl D. Hobart
U.S. Naval Research Laboratory
4 shared publications
Latest Publications
- 11 September 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (10)
Impact of dislocation motion on interdiffusion, structuring, and thermal transport at Ge–Si heterointerface
The roles of dislocation motion and interdiffusion on the interfacial morphology and thermal properties of the Ge–Si interface were elucidated using transmission electron microscopy, energy dispersive x-ray spectroscopy, and thermoreflectance measurements. Epitaxial Ge thin films deposited on Si (001) substrates by molecular beam epitaxy were annealed from 400 to 800 °C both in situ and ex situ in nitrogen to modify the interface morphology. Multiple transmission electron microscopy techniques monitored the evolution of defects and diffusion before and after different annealing treatments, revealing a strong correlation between dislocation motion and interdiffusion at the interface, producing a corrugated interface morphology. The characterization supports the fact that dislocations affect the interface structure by serving as vacancy sinks during their reconfiguration at elevated temperatures. Directed vacancy fluxes then enhance interdiffusion near dislocation cores, resulting in the periodic corrugation of the interface. Thermal measurements were performed to extract the thermal boundary resistance from the resulting interface morphologies produced by each annealing condition. Annealing resulted in increased thermal boundary resistance at the Ge–Si interface, largely attributed to alloy scattering becoming dominant as interdiffusion proceeds.
- 11 September 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (10)
Impact of dislocation motion on interdiffusion, structuring, and thermal transport at Ge–Si heterointerface
The roles of dislocation motion and interdiffusion on the interfacial morphology and thermal properties of the Ge–Si interface were elucidated using transmission electron microscopy, energy dispersive x-ray spectroscopy, and thermoreflectance measurements. Epitaxial Ge thin films deposited on Si (001) substrates by molecular beam epitaxy were annealed from 400 to 800 °C both in situ and ex situ in nitrogen to modify the interface morphology. Multiple transmission electron microscopy techniques monitored the evolution of defects and diffusion before and after different annealing treatments, revealing a strong correlation between dislocation motion and interdiffusion at the interface, producing a corrugated interface morphology. The characterization supports the fact that dislocations affect the interface structure by serving as vacancy sinks during their reconfiguration at elevated temperatures. Directed vacancy fluxes then enhance interdiffusion near dislocation cores, resulting in the periodic corrugation of the interface. Thermal measurements were performed to extract the thermal boundary resistance from the resulting interface morphologies produced by each annealing condition. Annealing resulted in increased thermal boundary resistance at the Ge–Si interface, largely attributed to alloy scattering becoming dominant as interdiffusion proceeds.
- Open Access
- 1 November 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (11)
Crack formation in strained β-(AlxGa1−x)2O3 films grown on (010) β-Ga2O3 substrates
The cracking and local strain relaxation in (010) (AlxGa1−x)2O3 films grown on Ga2O3 substrates are assessed in terms of film composition and thickness. We utilize x-ray diffraction and electron microscopy techniques combined with simulation and modeling to investigate that film cracking on curvature (flatness) has a directly proportional relationship with film thickness and/or aluminum content. Cross section transmission electron microscopy reveals that cracks along both the (001) and (100) cleavage planes penetrate into the substrate. The diffuse scattered intensity observed in reciprocal space maps (RSMs) is directly correlated with the tilt that is introduced due to the change in the deformation conditions near the cracks. While asymmetric RSMs show that the layers are fully strained, the diffuse scattering distribution in reciprocal space can be interpreted to show that the cracking relaxes and locally tilts the lattice ∼350 nm from the crack edges, which is consistent with the larger radius of curvature associated with the films with higher crack densities. For example, a 200 nm (Al0.13Ga0.87)2O3 thick film has an average inter-crack spacing of 3.3 µm, so most of the epitaxial layer is fully strained except near the cracks where it deforms elastically and is consistent with the gallium oxide Poisson ratio. A reciprocal space model was developed, which imports the strain and tilt distributions (based on finite element modeling) to match the features observed in the experimental maps. We also note that previous studies involving (AlxGa1−x)2O3 films may show evidence of cracking as observed in their symmetric and asymmetric RSMs.
- 1 November 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (11)
Open AccessCrack formation in strained β-(AlxGa1−x)2O3 films grown on (010) β-Ga2O3 substrates
The cracking and local strain relaxation in (010) (AlxGa1−x)2O3 films grown on Ga2O3 substrates are assessed in terms of film composition and thickness. We utilize x-ray diffraction and electron microscopy techniques combined with simulation and modeling to investigate that film cracking on curvature (flatness) has a directly proportional relationship with film thickness and/or aluminum content. Cross section transmission electron microscopy reveals that cracks along both the (001) and (100) cleavage planes penetrate into the substrate. The diffuse scattered intensity observed in reciprocal space maps (RSMs) is directly correlated with the tilt that is introduced due to the change in the deformation conditions near the cracks. While asymmetric RSMs show that the layers are fully strained, the diffuse scattering distribution in reciprocal space can be interpreted to show that the cracking relaxes and locally tilts the lattice ∼350 nm from the crack edges, which is consistent with the larger radius of curvature associated with the films with higher crack densities. For example, a 200 nm (Al0.13Ga0.87)2O3 thick film has an average inter-crack spacing of 3.3 µm, so most of the epitaxial layer is fully strained except near the cracks where it deforms elastically and is consistent with the gallium oxide Poisson ratio. A reciprocal space model was developed, which imports the strain and tilt distributions (based on finite element modeling) to match the features observed in the experimental maps. We also note that previous studies involving (AlxGa1−x)2O3 films may show evidence of cracking as observed in their symmetric and asymmetric RSMs.
- 23 December 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (26)
Experimental observation of ballistic to diffusive transition in phonon thermal transport of AlN thin films
Ultrawide bandgap semiconductor aluminum nitride (AlN) possesses high thermal conductivity in bulk form due to long phonon mean-free-paths, high group velocity, and long lifetimes. However, the thermal transport scenario becomes very different in a thin AlN film due to phonon-defect and phonon-boundary scattering. Herein, we report experimental observation of ballistic to diffusive transition in a series of AlN thin films (1.6–2440 nm) grown on sapphire substrates. The ballistic transport is characterized by constant thermal resistance as a function of film thickness due to phonon scattering by defects and boundaries. In this transport regime, phonons possess very small group velocities and lifetimes. A gradual increase in the optical phonon lifetime is observed in the diffusive regime. Our study will aid the incorporation of highly conductive thin film materials in the semiconductor production line for efficient thermal management.
- 23 December 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (26)
Experimental observation of ballistic to diffusive transition in phonon thermal transport of AlN thin films
Ultrawide bandgap semiconductor aluminum nitride (AlN) possesses high thermal conductivity in bulk form due to long phonon mean-free-paths, high group velocity, and long lifetimes. However, the thermal transport scenario becomes very different in a thin AlN film due to phonon-defect and phonon-boundary scattering. Herein, we report experimental observation of ballistic to diffusive transition in a series of AlN thin films (1.6–2440 nm) grown on sapphire substrates. The ballistic transport is characterized by constant thermal resistance as a function of film thickness due to phonon scattering by defects and boundaries. In this transport regime, phonons possess very small group velocities and lifetimes. A gradual increase in the optical phonon lifetime is observed in the diffusive regime. Our study will aid the incorporation of highly conductive thin film materials in the semiconductor production line for efficient thermal management.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (36) , 2524
(Invited) Heterointegration of Wide and Ultrawide Bandgap Semiconductors
Combinations of layers involving wide and ultra-wide bandgap materials for electronic benefits, thermal management, and other aspects can be achieved using heterointegration techniques that include but also go beyond epitaxial deposition. Here, we describe some important wide bandgap combinations achieved through wafer bonding / fusion / layer transfer / as well as deposition to demonstrate how control of interfaces can lead to better multi-layer performance and also how thermal transport models can be applied to these novel systems to lead to improvements in combined electronic and thermal management performance. Examples will include bonding using diamond, GaN-AlN bonding across N-face and metal face interfaces, and b-Ga2O3 structures. The importance of understanding interface preparation for both bonding and deposition applications as well as judicious introduction of thin interfacial layers will be described for such wide bandgap materials.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (36) , 2524
(Invited) Heterointegration of Wide and Ultrawide Bandgap Semiconductors
Combinations of layers involving wide and ultra-wide bandgap materials for electronic benefits, thermal management, and other aspects can be achieved using heterointegration techniques that include but also go beyond epitaxial deposition. Here, we describe some important wide bandgap combinations achieved through wafer bonding / fusion / layer transfer / as well as deposition to demonstrate how control of interfaces can lead to better multi-layer performance and also how thermal transport models can be applied to these novel systems to lead to improvements in combined electronic and thermal management performance. Examples will include bonding using diamond, GaN-AlN bonding across N-face and metal face interfaces, and b-Ga2O3 structures. The importance of understanding interface preparation for both bonding and deposition applications as well as judicious introduction of thin interfacial layers will be described for such wide bandgap materials.
- 5 February 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (6) , 8109-8118
Enhanced Thermal Boundary Conductance across GaN/SiC Interfaces with AlN Transition Layers
Heat dissipation plays a crucial role in the performance and reliability of high-power GaN-based electronics. While AlN transition layers are commonly employed in the heteroepitaxial growth of GaN-on-SiC substrates, concerns have been raised about their impact on thermal transport across GaN/SiC interfaces. In this study, we present experimental measurements of the thermal boundary conductance (TBC) across GaN/SiC interfaces with varying thicknesses of the AlN transition layer (ranging from 0 to 73 nm) at different temperatures. Our findings reveal that the addition of an AlN transition layer leads to a notable increase in the TBC of the GaN/SiC interface, particularly at elevated temperatures. Structural characterization techniques are employed to understand the influence of the AlN transition layer on the crystalline quality of the GaN layer and its potential effects on interfacial thermal transport. To gain further insights into the trend of TBC, we conduct molecular dynamics simulations using high-fidelity deep learning-based interatomic potentials, which reproduce the experimentally observed enhancement in TBC even for atomically perfect interfaces. These results suggest that the enhanced TBC facilitated by the AlN intermediate layer could result from a combination of improved crystalline quality at the interface and the "phonon bridge" effect provided by AlN that enhances the overlap between the vibrational spectra of GaN and SiC.
- 5 February 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (6) , 8109-8118
Enhanced Thermal Boundary Conductance across GaN/SiC Interfaces with AlN Transition Layers
Heat dissipation plays a crucial role in the performance and reliability of high-power GaN-based electronics. While AlN transition layers are commonly employed in the heteroepitaxial growth of GaN-on-SiC substrates, concerns have been raised about their impact on thermal transport across GaN/SiC interfaces. In this study, we present experimental measurements of the thermal boundary conductance (TBC) across GaN/SiC interfaces with varying thicknesses of the AlN transition layer (ranging from 0 to 73 nm) at different temperatures. Our findings reveal that the addition of an AlN transition layer leads to a notable increase in the TBC of the GaN/SiC interface, particularly at elevated temperatures. Structural characterization techniques are employed to understand the influence of the AlN transition layer on the crystalline quality of the GaN layer and its potential effects on interfacial thermal transport. To gain further insights into the trend of TBC, we conduct molecular dynamics simulations using high-fidelity deep learning-based interatomic potentials, which reproduce the experimentally observed enhancement in TBC even for atomically perfect interfaces. These results suggest that the enhanced TBC facilitated by the AlN intermediate layer could result from a combination of improved crystalline quality at the interface and the "phonon bridge" effect provided by AlN that enhances the overlap between the vibrational spectra of GaN and SiC.
- 11 January 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (2)
Dissolution of Mg-enriched defects in implanted GaN and increased p-type dopant activation
Annealing Mg-implanted homoepitaxial GaN at temperatures above 1400 °C eliminates the formation of inversion domains and leads to improved dopant activation efficiency. Extended defects, in the form of inversion domains, contain electrically inactive Mg after post-implantation annealing at temperatures as high as 1300 °C (one GPa N2 overpressure), which results in a low dopant activation efficiency. Triple-axis x-ray data reveal that implant-induced strain is fully relieved after annealing at 1300 °C for 10 min, indicating that strain-inducing point defects formed during implantation have reconfigured and inversion domains are formed. However, annealing at temperatures of 1400–1500 °C (one GPa N2 overpressure) eliminates the presence of the inversion domains. While residual defects, such as dislocation loops, still exist after annealing at and above 1400 °C, chemical analysis at multiple dislocation loops shows no sign of Mg segregation. Meanwhile, an overall decreasing trend in the dislocation loop density is observed after annealing at the higher temperatures and longer times. Additionally, once inversion domains are formed and the samples are cooled to room temperature, they are shown to dissolve with subsequent annealing above 1400 °C. While such defects have been observed before, the important finding that such defects can be dissolved with a short, higher temperature step is key. Earlier work [Breckenridge et al., J. Appl. Phys. Lett. 118, 022101 (2021)] addressing electrical measurements of these types of samples showed that annealing at 1400 °C leads to a dopant activation efficiency that is an order of magnitude higher than that observed at 1300 °C. This work complements earlier work by identifying the inversion domains, which incorporate Mg, and points to the benefits, in terms of defect density and p-type dopant activation, of using higher temperature (>1400 °C) annealing cycles to activate Mg in GaN, even if the Mg-containing inversion domains had been formed during lower temperature annealing.
- 11 January 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (2)
Dissolution of Mg-enriched defects in implanted GaN and increased p-type dopant activation
Annealing Mg-implanted homoepitaxial GaN at temperatures above 1400 °C eliminates the formation of inversion domains and leads to improved dopant activation efficiency. Extended defects, in the form of inversion domains, contain electrically inactive Mg after post-implantation annealing at temperatures as high as 1300 °C (one GPa N2 overpressure), which results in a low dopant activation efficiency. Triple-axis x-ray data reveal that implant-induced strain is fully relieved after annealing at 1300 °C for 10 min, indicating that strain-inducing point defects formed during implantation have reconfigured and inversion domains are formed. However, annealing at temperatures of 1400–1500 °C (one GPa N2 overpressure) eliminates the presence of the inversion domains. While residual defects, such as dislocation loops, still exist after annealing at and above 1400 °C, chemical analysis at multiple dislocation loops shows no sign of Mg segregation. Meanwhile, an overall decreasing trend in the dislocation loop density is observed after annealing at the higher temperatures and longer times. Additionally, once inversion domains are formed and the samples are cooled to room temperature, they are shown to dissolve with subsequent annealing above 1400 °C. While such defects have been observed before, the important finding that such defects can be dissolved with a short, higher temperature step is key. Earlier work [Breckenridge et al., J. Appl. Phys. Lett. 118, 022101 (2021)] addressing electrical measurements of these types of samples showed that annealing at 1400 °C leads to a dopant activation efficiency that is an order of magnitude higher than that observed at 1300 °C. This work complements earlier work by identifying the inversion domains, which incorporate Mg, and points to the benefits, in terms of defect density and p-type dopant activation, of using higher temperature (>1400 °C) annealing cycles to activate Mg in GaN, even if the Mg-containing inversion domains had been formed during lower temperature annealing.
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (33) , 1606
Improved Thermal Boundary Conductance in Annealed Direct Wafer Bonded Si-Ge
The evolution of structural and thermal properties of wafer bonded Si|Ge with annealing is investigated in this study. Theoretical work suggests that the thermal boundary conductance between amorphous Si and Ge provide improved thermal properties as compared to a crystalline Si to Ge interface, and wafer bonded systems provides a fabrication method to experimentally test this theory [1]. EVG® ComBond® equipment was used for bonding under high vacuum (~10-8 mtorr) at room temperature to remove unwanted native surface oxides [2-4]. The bombardment of the surfaces prior to bonding produces an amorphous region at the bonded interface that has been seen in many other bonded systems [5,6]. In the as-bonded sample, high resolution scanning transmission electron microscopy revealed a ~1.2 nm amorphous region at the bonded interface. Subsequent annealing was done in an effort to recrystallize the amorphous interface. Previous work has shown that recrystallization between Si|Si wafer bonded samples occurred when annealed at 450 °C for 12 hours [3]. After annealing at 600 °C for 2 hours, the amorphous interface was observed to decrease to ~0.9 nm. Complete recrystallization is observed when the sample was annealed at 600 °C for 48 hours. Preliminary thermal results show that the thermal boundary conductance (TBC) of the as bonded sample is 47 ± 5 MW/(m2K). The TBC for the sample annealed at 600 °C for 48 hours is 94 ± 5 MW/(m2K), an improvement by a factor of two compared to the as-bonded interface. These results demonstrate that the TBC can be improved through annealing of the interface and that improvements due to an amorphous-amorphous interface do not dominate the thermal boundary conductance in this system. We consider that the improvements are due to recrystallization of the interface and/or to increased interdiffusion, which has been observed to increase TBC in epitaxially grown Si-Ge interfaces [7]. K. Gordiz, et al., J. Appl. Phys., 121(2), p.025102 (2017) V. Dragoi, et al., ECS Trans., 86(5), 23 (2018) C. Flötgen, et al., ECS Trans., 64(5), 103 (2014) M.E. Liao, et al., ECS Trans., 86(5), 55 (2018) Y. Xu, et al., Ceramics International, 45, 6552 (2019) F. Mu, et al., Appl. Surf. Sci., 416, 1007 (2017) Z. Cheng, et al., Nature communications, 12(1), p.6901 (2021) Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (33) , 1606
Improved Thermal Boundary Conductance in Annealed Direct Wafer Bonded Si-Ge
The evolution of structural and thermal properties of wafer bonded Si|Ge with annealing is investigated in this study. Theoretical work suggests that the thermal boundary conductance between amorphous Si and Ge provide improved thermal properties as compared to a crystalline Si to Ge interface, and wafer bonded systems provides a fabrication method to experimentally test this theory [1]. EVG® ComBond® equipment was used for bonding under high vacuum (~10-8 mtorr) at room temperature to remove unwanted native surface oxides [2-4]. The bombardment of the surfaces prior to bonding produces an amorphous region at the bonded interface that has been seen in many other bonded systems [5,6]. In the as-bonded sample, high resolution scanning transmission electron microscopy revealed a ~1.2 nm amorphous region at the bonded interface. Subsequent annealing was done in an effort to recrystallize the amorphous interface. Previous work has shown that recrystallization between Si|Si wafer bonded samples occurred when annealed at 450 °C for 12 hours [3]. After annealing at 600 °C for 2 hours, the amorphous interface was observed to decrease to ~0.9 nm. Complete recrystallization is observed when the sample was annealed at 600 °C for 48 hours. Preliminary thermal results show that the thermal boundary conductance (TBC) of the as bonded sample is 47 ± 5 MW/(m2K). The TBC for the sample annealed at 600 °C for 48 hours is 94 ± 5 MW/(m2K), an improvement by a factor of two compared to the as-bonded interface. These results demonstrate that the TBC can be improved through annealing of the interface and that improvements due to an amorphous-amorphous interface do not dominate the thermal boundary conductance in this system. We consider that the improvements are due to recrystallization of the interface and/or to increased interdiffusion, which has been observed to increase TBC in epitaxially grown Si-Ge interfaces [7]. K. Gordiz, et al., J. Appl. Phys., 121(2), p.025102 (2017) V. Dragoi, et al., ECS Trans., 86(5), 23 (2018) C. Flötgen, et al., ECS Trans., 64(5), 103 (2014) M.E. Liao, et al., ECS Trans., 86(5), 55 (2018) Y. Xu, et al., Ceramics International, 45, 6552 (2019) F. Mu, et al., Appl. Surf. Sci., 416, 1007 (2017) Z. Cheng, et al., Nature communications, 12(1), p.6901 (2021) Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (33) , 1624
Direct Wafer Bonding of 128° Y-Cut LiNbO3: A Pathway to High Frequency (50 GHz) Filter Applications
In this work, room temperature direct wafer bonding of complementarily oriented 128° Y-cut LiNbO3 substrates is achieved with an interfacial layer less than 1 nm thick. This compares well to commercially available structures with thickness of 3 nm and this interfacial width is particularly important for eventual multilayer bonding sequences with each layer on the order of only tens of nm. The (0114) indices describe the surface plane of 128° Y-cut LiNbO3 wafers; and the wafers were bonded such that their in-plane [055.12] directions were antiparallel. Due to its trigonal crystal structure, this zone axis has 1-fold symmetry and therefore is crystallographically distinguishable from either side of the bonded interface. The wafers were cleaned with standard cleaning protocols and subsequently brought in contact face-to-face and bonded. The bonding was performed in ambient atmosphere and the applied pressure was on the order of ~kPa. The bonded pair was then annealed at 200 °C for 10 h in order to strengthen the bond, which is fully compatible with exfoliation of He-implanted LiNbO3 layers. Limited literature has been reported for direct bonding of LiNbO3 to LiNbO3 and even fewer investigate the atomic structure of the bonded interface.1-3 Tomita et al., observe structurally disordered bonded interfaces after annealing at high temperatures (up to 1000 °C). High resolution transmission electron microscopy of the interface presented here reveal an abrupt interface (≤ ~1 nm) and a φ X-ray scan has confirmed a relative twist of ~180° between substrates. This is a follow-up work for what has previously been achieved by our group demonstrating direct wafer bonding and layer transfer of LiNbO3 to substrates such as sapphire and oxidized silicon.4 Combining these latest results will enable the fabrication of a multilayer structure of complementarily oriented LiNbO3 thin films on a sapphire substrate, which has applications for high frequency (50 GHz) filters. Similar structures using a different LiNbO3 orientation (X-cut) have been demonstrated to maintain high quality factor (Q) at 15.8 GHz.5 The authors would like to acknowledge the support from DARPA through the Compact Front-end Filters at the ElEment-level (COFFEE) program. [1] Tulli, D., Janner, D. and Pruneri, V., “Room temperature direct bonding of LiNbO3 crystal layers and its application to high-voltage optical sensing.” Journal of Micromechanics and Microengineering, 21(8), p.085025 (2011). [2] Tomita, Y., Sugimoto, M., & Eda, K., “Direct bonding of LiNbO3 single crystals for optical waveguides.” Applied physics letters, 66(12), 1484-1485 (1995). [3] Berini, P., Mattiussi, G., Lahoud, N. and Charbonneau, R., “Wafer-bonded surface plasmon waveguides.” Applied physics letters, 90(6), p.061108 (2007). [4] Liao, M. E., Matto, L., Huynh, K., and Goorsky, M. S., “Direct Wafer Bonding of 128° Y-Cut LiNbO3 to Sapphire”. WaferBond ’22, Presentation (2022). [5] Lu, R., and Gong, S., 2021 Joint Conf. EFTF/IFCS, 1 (2021). Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (33) , 1624
Direct Wafer Bonding of 128° Y-Cut LiNbO3: A Pathway to High Frequency (50 GHz) Filter Applications
In this work, room temperature direct wafer bonding of complementarily oriented 128° Y-cut LiNbO3 substrates is achieved with an interfacial layer less than 1 nm thick. This compares well to commercially available structures with thickness of 3 nm and this interfacial width is particularly important for eventual multilayer bonding sequences with each layer on the order of only tens of nm. The (0114) indices describe the surface plane of 128° Y-cut LiNbO3 wafers; and the wafers were bonded such that their in-plane [055.12] directions were antiparallel. Due to its trigonal crystal structure, this zone axis has 1-fold symmetry and therefore is crystallographically distinguishable from either side of the bonded interface. The wafers were cleaned with standard cleaning protocols and subsequently brought in contact face-to-face and bonded. The bonding was performed in ambient atmosphere and the applied pressure was on the order of ~kPa. The bonded pair was then annealed at 200 °C for 10 h in order to strengthen the bond, which is fully compatible with exfoliation of He-implanted LiNbO3 layers. Limited literature has been reported for direct bonding of LiNbO3 to LiNbO3 and even fewer investigate the atomic structure of the bonded interface.1-3 Tomita et al., observe structurally disordered bonded interfaces after annealing at high temperatures (up to 1000 °C). High resolution transmission electron microscopy of the interface presented here reveal an abrupt interface (≤ ~1 nm) and a φ X-ray scan has confirmed a relative twist of ~180° between substrates. This is a follow-up work for what has previously been achieved by our group demonstrating direct wafer bonding and layer transfer of LiNbO3 to substrates such as sapphire and oxidized silicon.4 Combining these latest results will enable the fabrication of a multilayer structure of complementarily oriented LiNbO3 thin films on a sapphire substrate, which has applications for high frequency (50 GHz) filters. Similar structures using a different LiNbO3 orientation (X-cut) have been demonstrated to maintain high quality factor (Q) at 15.8 GHz.5 The authors would like to acknowledge the support from DARPA through the Compact Front-end Filters at the ElEment-level (COFFEE) program. [1] Tulli, D., Janner, D. and Pruneri, V., “Room temperature direct bonding of LiNbO3 crystal layers and its application to high-voltage optical sensing.” Journal of Micromechanics and Microengineering, 21(8), p.085025 (2011). [2] Tomita, Y., Sugimoto, M., & Eda, K., “Direct bonding of LiNbO3 single crystals for optical waveguides.” Applied physics letters, 66(12), 1484-1485 (1995). [3] Berini, P., Mattiussi, G., Lahoud, N. and Charbonneau, R., “Wafer-bonded surface plasmon waveguides.” Applied physics letters, 90(6), p.061108 (2007). [4] Liao, M. E., Matto, L., Huynh, K., and Goorsky, M. S., “Direct Wafer Bonding of 128° Y-Cut LiNbO3 to Sapphire”. WaferBond ’22, Presentation (2022). [5] Lu, R., and Gong, S., 2021 Joint Conf. EFTF/IFCS, 1 (2021). Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (33) , 1605
Stability of Interface Morphology and Thermal Boundary Conductance of Direct Wafer Bonded GaN|Si Heterojunction Interfaces Annealed at Growth and Annealing Temperatures
The properties of thin (~2 um) GaN templates on a silicon support substrate were studied to assess the stability of the direct wafer bonded GaN / Si interface. EVG® ComBond® equipment was used for bonding under high vacuum (~10-8 mtorr) at room temperature to remove unwanted native surface oxides [1,2]. For the bonded samples, the [1010] GaN edge was aligned parallel to the Si [110] edge. An X-ray diffraction reciprocal space map of the (004) Si and (0004) GaN revealed that there is a ~0.2° tilt between the GaN and Si layers and is simply due to the relative miscut between the two wafers. The treatment of the surfaces prior to bonding produces an amorphous region at the bonded interface that has been seen in many other bonded systems [3-5]. In the as-bonded sample, high resolution scanning transmission electron microscopy revealed a ~2 nm amorphous region on the Si side of the bonded interface, as confirmed by energy dispersive x-ray spectroscopy (EDX). Subsequent annealing was performed in an effort to recrystallize the amorphous interface. Previous work has shown that recrystallization between Si|Si wafer bonded samples occurred when annealed at 450 °C for 12 hours [3]. However, in the GaN|Si system, we found that the amorphous interface did not recrystallize when annealed under those conditions. Annealing at temperatures up to 450 °C and 120 hours showed only initial stages of interdiffusion and a stable interface. However, after annealing at 700 °C for 24 hours, high resolution EDX revealed the formation of amorphous SiN as well as the diffusion of gallium into silicon. Preliminary thermal results show that the thermal boundary conductance (TBC) of the as bonded sample is ~140 MW/(m2K). The TBC results of wafer bonded GaN|Si reported here is higher than previously reported TBC values of epitaxially grown interfaces such as GaN on Si [6], GaN on SiC [7], and GaN on diamond [8]. The TBC for the annealed interface is degraded by a factor of two compared to the as-bonded interface for the sample that was annealed at 700 °C for 24 hours. These results demonstrate that high TBC can be achieved through wafer bonding of GaN with materials such as silicon and that such interfaces are stable even up to device operation up to 300 °C. However, chemically rough interfaces formed due to high temperature annealing are detrimental to thermal transport across these interfaces. V. Dragoi, et al., ECS Trans., 86(5), 23 (2018) C. Flötgen, et al., ECS Trans., 64(5), 103 (2014) M.E. Liao, et al., ECS Trans., 86(5), 55 (2018) Y. Xu, et al., Ceramics International, 45, 6552 (2019) F. Mu, et al., Appl. Surf. Sci., 416, 1007 (2017) L. Yates, et al., ASME InterPACK (2015) J. Cho, et al., Phys. Rev. B, 89, 115301 (2014) H. Sun, et al., APL, 106(11), 111906 (2015) Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (33) , 1605
Stability of Interface Morphology and Thermal Boundary Conductance of Direct Wafer Bonded GaN|Si Heterojunction Interfaces Annealed at Growth and Annealing Temperatures
The properties of thin (~2 um) GaN templates on a silicon support substrate were studied to assess the stability of the direct wafer bonded GaN / Si interface. EVG® ComBond® equipment was used for bonding under high vacuum (~10-8 mtorr) at room temperature to remove unwanted native surface oxides [1,2]. For the bonded samples, the [1010] GaN edge was aligned parallel to the Si [110] edge. An X-ray diffraction reciprocal space map of the (004) Si and (0004) GaN revealed that there is a ~0.2° tilt between the GaN and Si layers and is simply due to the relative miscut between the two wafers. The treatment of the surfaces prior to bonding produces an amorphous region at the bonded interface that has been seen in many other bonded systems [3-5]. In the as-bonded sample, high resolution scanning transmission electron microscopy revealed a ~2 nm amorphous region on the Si side of the bonded interface, as confirmed by energy dispersive x-ray spectroscopy (EDX). Subsequent annealing was performed in an effort to recrystallize the amorphous interface. Previous work has shown that recrystallization between Si|Si wafer bonded samples occurred when annealed at 450 °C for 12 hours [3]. However, in the GaN|Si system, we found that the amorphous interface did not recrystallize when annealed under those conditions. Annealing at temperatures up to 450 °C and 120 hours showed only initial stages of interdiffusion and a stable interface. However, after annealing at 700 °C for 24 hours, high resolution EDX revealed the formation of amorphous SiN as well as the diffusion of gallium into silicon. Preliminary thermal results show that the thermal boundary conductance (TBC) of the as bonded sample is ~140 MW/(m2K). The TBC results of wafer bonded GaN|Si reported here is higher than previously reported TBC values of epitaxially grown interfaces such as GaN on Si [6], GaN on SiC [7], and GaN on diamond [8]. The TBC for the annealed interface is degraded by a factor of two compared to the as-bonded interface for the sample that was annealed at 700 °C for 24 hours. These results demonstrate that high TBC can be achieved through wafer bonding of GaN with materials such as silicon and that such interfaces are stable even up to device operation up to 300 °C. However, chemically rough interfaces formed due to high temperature annealing are detrimental to thermal transport across these interfaces. V. Dragoi, et al., ECS Trans., 86(5), 23 (2018) C. Flötgen, et al., ECS Trans., 64(5), 103 (2014) M.E. Liao, et al., ECS Trans., 86(5), 55 (2018) Y. Xu, et al., Ceramics International, 45, 6552 (2019) F. Mu, et al., Appl. Surf. Sci., 416, 1007 (2017) L. Yates, et al., ASME InterPACK (2015) J. Cho, et al., Phys. Rev. B, 89, 115301 (2014) H. Sun, et al., APL, 106(11), 111906 (2015) Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (33) , 1622
Towards Controlled Transfer of (001) β-Ga2O3 to (0001) 4H-SiC Substrates
We demonstrate successful blistering of He-implanted (001) β-Ga2O3, bonding to (0001) 4H-SiC, and initial results towards large-area transfer of (001) β-Ga2O3 to 4H-SiC. Compatible with large-scale processing, exfoliation is an important step in controlled-thickness transfer of films for heterogeneous integration. Furthermore, integration of β-Ga2O3 to high thermal conductivity materials will be crucial for thermal management of β-Ga2O3-based power devices. Two-inch (001) β-Ga2O3 wafers were implanted with He+ at an energy of 160 keV and a dose of 5×1016 cm-2, which are the same implant parameters used previously to successfully exfoliate (010) β-Ga2O3.1 Strain fringes were observed after the implant which corresponded to a maximum strain of ~1.7%, which is higher than the ~1% strain when implanting (010) β-Ga2O31 likely due to the larger Poisson’s ratio of (001) β-Ga2O3.2 The implanted substrates were then bonded to (0001) 4H-SiC at room temperature using a ~5 nm thin Ti interlayer to assist with the bond. Both unbonded implanted substrates and the bonded structures were first annealed at 200 °C for 10 hours to simultaneously initiate He bubble nucleation at the implanted projected range (~0.68 μm) and strengthen the bond. Then, even after annealing at 500 °C for 10 hours to initiate He bubble growth, the (001) β-Ga2O3 did not transfer to the (0001) 4H-SiC. Unlike what was observed for (010) β-Ga2O3,1 blistering did not even occur at this temperature. Annealing at 800 °C for up to 12 hours resulted in ~10 μm blisters for the unbonded substrates, which is typically an indication that large wafer-area transfer can be achieved if bonding was done prior to annealing.3 However, the β-Ga2O3 substrate did not wafer split from the bonded structure, and instead only small area transfers up to ~200 μm were achieved. Only ~7% of the total bonded area transferred while the entire structure remained bonded. Strategies to improve transfer will be presented, including initiating a cold split prior to exfoliation and refined annealing strategies to improve He bubble nucleation and larger bubble growth at the projected range. These are promising results towards achieving large wafer-scale (001) β-Ga2O3 composite wafers, and when combined with subsurface damage-free chemical mechanical polishing,4 these composite wafers would be suitable for subsequent devices and/or epitaxial growth. The authors would like to acknowledge the support from the Office of Naval Research through a MURI program, grant No. N00014-18-1-2429. This research was performed while M.E.L. and J.S.L. held an NRC Research Associateship award at the U.S. Naval Research Laboratory. References M.E. Liao, et al., ECS J. Solid State Sci. Technol., 8(11), P673 (2019). K. Adachi, et al., J. Appl. Phys., 124, 085102 (2018). M. Bruel, et al., Jpn. J. Appl. Phys., 36, 1636 (1997). M.E. Liao, et al., J. Vac. Sci. Technol. A, 41, 013205 (2023). Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (33) , 1622
Towards Controlled Transfer of (001) β-Ga2O3 to (0001) 4H-SiC Substrates
We demonstrate successful blistering of He-implanted (001) β-Ga2O3, bonding to (0001) 4H-SiC, and initial results towards large-area transfer of (001) β-Ga2O3 to 4H-SiC. Compatible with large-scale processing, exfoliation is an important step in controlled-thickness transfer of films for heterogeneous integration. Furthermore, integration of β-Ga2O3 to high thermal conductivity materials will be crucial for thermal management of β-Ga2O3-based power devices. Two-inch (001) β-Ga2O3 wafers were implanted with He+ at an energy of 160 keV and a dose of 5×1016 cm-2, which are the same implant parameters used previously to successfully exfoliate (010) β-Ga2O3.1 Strain fringes were observed after the implant which corresponded to a maximum strain of ~1.7%, which is higher than the ~1% strain when implanting (010) β-Ga2O31 likely due to the larger Poisson’s ratio of (001) β-Ga2O3.2 The implanted substrates were then bonded to (0001) 4H-SiC at room temperature using a ~5 nm thin Ti interlayer to assist with the bond. Both unbonded implanted substrates and the bonded structures were first annealed at 200 °C for 10 hours to simultaneously initiate He bubble nucleation at the implanted projected range (~0.68 μm) and strengthen the bond. Then, even after annealing at 500 °C for 10 hours to initiate He bubble growth, the (001) β-Ga2O3 did not transfer to the (0001) 4H-SiC. Unlike what was observed for (010) β-Ga2O3,1 blistering did not even occur at this temperature. Annealing at 800 °C for up to 12 hours resulted in ~10 μm blisters for the unbonded substrates, which is typically an indication that large wafer-area transfer can be achieved if bonding was done prior to annealing.3 However, the β-Ga2O3 substrate did not wafer split from the bonded structure, and instead only small area transfers up to ~200 μm were achieved. Only ~7% of the total bonded area transferred while the entire structure remained bonded. Strategies to improve transfer will be presented, including initiating a cold split prior to exfoliation and refined annealing strategies to improve He bubble nucleation and larger bubble growth at the projected range. These are promising results towards achieving large wafer-scale (001) β-Ga2O3 composite wafers, and when combined with subsurface damage-free chemical mechanical polishing,4 these composite wafers would be suitable for subsequent devices and/or epitaxial growth. The authors would like to acknowledge the support from the Office of Naval Research through a MURI program, grant No. N00014-18-1-2429. This research was performed while M.E.L. and J.S.L. held an NRC Research Associateship award at the U.S. Naval Research Laboratory. References M.E. Liao, et al., ECS J. Solid State Sci. Technol., 8(11), P673 (2019). K. Adachi, et al., J. Appl. Phys., 124, 085102 (2018). M. Bruel, et al., Jpn. J. Appl. Phys., 36, 1636 (1997). M.E. Liao, et al., J. Vac. Sci. Technol. A, 41, 013205 (2023). Figure 1