Jonathan Linden Bryan
Jonathan Linden Bryan has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Apostolos Kantzas
Department of Chemical and Petroleum Engineering, University of Calgary, Calgary, AB T2N 1N4, Canada
2 shared publications A. Voroniak
University of Calgary
1 shared publication- Alexey Cheremisin
Skolkovo Institute of Science and Technology, Moscow 143026, Russia
1 shared publication Aman Turakhanov
Centre for Petroleum Science and Engineering, Skolkovo Institute of Science and Technology, Moscow, Russian Federation
1 shared publicationAshling (Mehdi) Leilaeioun
School of Electrical, Computer, and Energy Engineering, Arizona State University, Tempe, Arizona, United States
1 shared publication- Dmitry Koroteev
Skolkovo Institute of Science and Technology Moscow Russia
1 shared publication
Latest Publications
- Open Access
- 17 August 2022
- Published by Springer Nature in Scientific Reports
- Vol. 12 (1) , 1-14
Application of XGBoost model for in-situ water saturation determination in Canadian oil-sands by LF-NMR and density data
Water saturation determination is among the most challenging tasks in petrophysical well-logging, which directly impacts the decision-making process in hydrocarbon exploration and production. Low-field nuclear magnetic resonance (LF-NMR) measurements can provide reliable evaluation. However, quantification of oil and water volumes is problematic when their NMR signals are not distinct. To overcome this, we developed two machine learning frameworks for predicting relative water content in oil-sand samples using LF-NMR spin–spin (T2) relaxation and bulk density data to derive a model based on Extreme Gradient Boosting. The first one facilitates feature engineering based on empirical knowledge from the T2 relaxation distribution analysis domain and mutual information feature extraction technique, while the second model considers whole samples’ NMR T2-relaxation distribution. The NMR T2 distributions were obtained for 82 Canadian oil-sands samples at ambient and reservoir temperatures (164 data points). The true water content was determined by Dean-Stark extraction. The statistical scores confirm the strong generalization ability of the feature engineering LF-NMR model in predicting relative water content by Dean-Stark—root-mean-square error of 0.67% and mean-absolute error of 0.53% (R2 = 0.90). Results indicate that this approach can be extended for the improved in-situ water saturation evaluation by LF-NMR and bulk density measurements.
- 17 August 2022
- Published by Springer Nature in Scientific Reports
- Vol. 12 (1) , 1-14
Open AccessApplication of XGBoost model for in-situ water saturation determination in Canadian oil-sands by LF-NMR and density data
Water saturation determination is among the most challenging tasks in petrophysical well-logging, which directly impacts the decision-making process in hydrocarbon exploration and production. Low-field nuclear magnetic resonance (LF-NMR) measurements can provide reliable evaluation. However, quantification of oil and water volumes is problematic when their NMR signals are not distinct. To overcome this, we developed two machine learning frameworks for predicting relative water content in oil-sand samples using LF-NMR spin–spin (T2) relaxation and bulk density data to derive a model based on Extreme Gradient Boosting. The first one facilitates feature engineering based on empirical knowledge from the T2 relaxation distribution analysis domain and mutual information feature extraction technique, while the second model considers whole samples’ NMR T2-relaxation distribution. The NMR T2 distributions were obtained for 82 Canadian oil-sands samples at ambient and reservoir temperatures (164 data points). The true water content was determined by Dean-Stark extraction. The statistical scores confirm the strong generalization ability of the feature engineering LF-NMR model in predicting relative water content by Dean-Stark—root-mean-square error of 0.67% and mean-absolute error of 0.53% (R2 = 0.90). Results indicate that this approach can be extended for the improved in-situ water saturation evaluation by LF-NMR and bulk density measurements.
- 13 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 12 (1) , 293-300
Systematic Operating Temperature Differences Between Al-BSF, PERC, and PERT-With-Optimized-Rear-Reflector Solar Mini-Modules Due to Rear Reflectance
Reflecting sub-bandgap light from photovoltaic modules has the potential to improve lifetime energy generation of fielded systems by reducing operating temperature. In this article, the temperature of fielded aluminum back-surface field (Al-BSF) and passivated emitter and rear contact (PERC) mini-modules was monitored every 5 minutes for 75 days along with corresponding meteorological data. Additionally, passivated emitter rear totally diffused (PERT) mini-modules with high-performance sub-bandgap rear reflectors were tested and compared to the state-of-the-art industrial modules. These reflectors consisted of a >300-nm-thick silicon dioxide nanoparticle film with a low refractive index. The impact of reflectance on measured operating temperature was isolated with a previously developed thermal model and quantified as the reflectance-induced median temperature difference between each tested module at representative outdoor conditions (1000 W·m −2 , 25 °C ambient temperature, and 1.43 m·s -1 wind speed). We found that, because of their reflectance differences, PERC modules ran systematically cooler than Al-BSF modules by 1.0 °C, whereas the PERT-with-optimized-rear-reflector systematically operated 1.4 °C cooler than the Al-BSF module and 0.4 °C than the PERC module. We also found that the rear reflector provided the greatest temperature benefit during periods of highest irradiance.
- 13 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 12 (1) , 293-300
Systematic Operating Temperature Differences Between Al-BSF, PERC, and PERT-With-Optimized-Rear-Reflector Solar Mini-Modules Due to Rear Reflectance
Reflecting sub-bandgap light from photovoltaic modules has the potential to improve lifetime energy generation of fielded systems by reducing operating temperature. In this article, the temperature of fielded aluminum back-surface field (Al-BSF) and passivated emitter and rear contact (PERC) mini-modules was monitored every 5 minutes for 75 days along with corresponding meteorological data. Additionally, passivated emitter rear totally diffused (PERT) mini-modules with high-performance sub-bandgap rear reflectors were tested and compared to the state-of-the-art industrial modules. These reflectors consisted of a >300-nm-thick silicon dioxide nanoparticle film with a low refractive index. The impact of reflectance on measured operating temperature was isolated with a previously developed thermal model and quantified as the reflectance-induced median temperature difference between each tested module at representative outdoor conditions (1000 W·m −2 , 25 °C ambient temperature, and 1.43 m·s -1 wind speed). We found that, because of their reflectance differences, PERC modules ran systematically cooler than Al-BSF modules by 1.0 °C, whereas the PERT-with-optimized-rear-reflector systematically operated 1.4 °C cooler than the Al-BSF module and 0.4 °C than the PERC module. We also found that the rear reflector provided the greatest temperature benefit during periods of highest irradiance.
- 4 February 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (13) , 134002
Aluminum–silicon interdiffusion in silicon heterojunction solar cells with a-Si:H(i)/a-Si:H(n/p)/Al rear contacts
We characterize a-Si:H(i)/a-Si:H(n)/Al and a-Si:H(i)/a-Si:H(p)/Al contacts implemented on the rear side of silicon heterojunction solar cells. Electrical test structures and full-area solar cells employing these contacts demonstrate promising performance. For example, a-Si:H(i)/a-Si:H(p)/Al test structures with a 40 nm thick a-Si:H(p) layer that were annealed at 180 °C had contact resistivities of 48 mΩ · cm 2 and implied open-circuit voltage losses after metallization of only 9 mV. Similarly, solar cells with full-area rear a-Si:H(i)/a-Si:H(n)/Al contacts that were annealed at 150 °C had open-circuit voltages of 717 mV and contact resistivities of 9.4 mΩ · cm 2 . For thinner doped a-Si:H layers and higher annealing temperatures, the contacts become less stable and performance degrades. Complementary transmission electron microscopy and energy-dispersive x-ray spectroscopy analysis show the Al–Si interactions at these interfaces that explain the range of exhibited performance. This analysis leads to a better understanding of the materials properties limiting the contact stability.
- 4 February 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (13) , 134002
Aluminum–silicon interdiffusion in silicon heterojunction solar cells with a-Si:H(i)/a-Si:H(n/p)/Al rear contacts
We characterize a-Si:H(i)/a-Si:H(n)/Al and a-Si:H(i)/a-Si:H(p)/Al contacts implemented on the rear side of silicon heterojunction solar cells. Electrical test structures and full-area solar cells employing these contacts demonstrate promising performance. For example, a-Si:H(i)/a-Si:H(p)/Al test structures with a 40 nm thick a-Si:H(p) layer that were annealed at 180 °C had contact resistivities of 48 mΩ · cm 2 and implied open-circuit voltage losses after metallization of only 9 mV. Similarly, solar cells with full-area rear a-Si:H(i)/a-Si:H(n)/Al contacts that were annealed at 150 °C had open-circuit voltages of 717 mV and contact resistivities of 9.4 mΩ · cm 2 . For thinner doped a-Si:H layers and higher annealing temperatures, the contacts become less stable and performance degrades. Complementary transmission electron microscopy and energy-dispersive x-ray spectroscopy analysis show the Al–Si interactions at these interfaces that explain the range of exhibited performance. This analysis leads to a better understanding of the materials properties limiting the contact stability.
- 26 September 2016
- Published by Society of Petroleum Engineers (SPE)
Two-Dimensional Visualization of Heavy Oil Displacement Mechanism During Chemical Flooding
There have been numerous laboratory tests conducted in recent years, studying the potential for heavy oil recovery through chemical addition (polymers and surfactants). In these tests, recovery is often understood in terms of pre-water breakthrough and post-water breakthrough improved oil recovery. Pre-breakthrough tests focus on viscous fingering and sweep efficiency from water vs. polymer additives. Post breakthrough tests study the potential for oil recovery after a waterflood has already been run: in these systems surfactants and polymers are added and there is conclusive evidence that chemical additives can be very effective at improving heavy oil recovery at the scale of these core flood systems. The observation made in laboratory core floods is that chemical recovery of oil is achieved under very high pressure gradients. The mechanism proposed in these tests is that chemicals plug water pathways and lead to improved sweep within the core. In reservoir applications of this technology, these same conditions may not be met and it is unclear whether these chemicals will still be as effective in non-linear systems. This study shows tests run in a 2D Hele-Shaw cell, which displaces oil with no pore scale trapping and with many open flow pathways like what is expected in the field. The objective of running tests in this system is to understand the mechanisms of heavy oil recovery and to observe whether chemical additives can still be successful for producing heavy oil in non-linear core systems with no capillary trapping.
- 26 September 2016
- Published by Society of Petroleum Engineers (SPE)
Two-Dimensional Visualization of Heavy Oil Displacement Mechanism During Chemical Flooding
There have been numerous laboratory tests conducted in recent years, studying the potential for heavy oil recovery through chemical addition (polymers and surfactants). In these tests, recovery is often understood in terms of pre-water breakthrough and post-water breakthrough improved oil recovery. Pre-breakthrough tests focus on viscous fingering and sweep efficiency from water vs. polymer additives. Post breakthrough tests study the potential for oil recovery after a waterflood has already been run: in these systems surfactants and polymers are added and there is conclusive evidence that chemical additives can be very effective at improving heavy oil recovery at the scale of these core flood systems. The observation made in laboratory core floods is that chemical recovery of oil is achieved under very high pressure gradients. The mechanism proposed in these tests is that chemicals plug water pathways and lead to improved sweep within the core. In reservoir applications of this technology, these same conditions may not be met and it is unclear whether these chemicals will still be as effective in non-linear systems. This study shows tests run in a 2D Hele-Shaw cell, which displaces oil with no pore scale trapping and with many open flow pathways like what is expected in the field. The objective of running tests in this system is to understand the mechanisms of heavy oil recovery and to observe whether chemical additives can still be successful for producing heavy oil in non-linear core systems with no capillary trapping.