Jow-Lian Ding
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jow-Lian Ding has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Yao Chen
School of Mechanical and Materials Engineering, Washington State University, Pullman, WA, 99164-2920, USA
2 shared publications- Amit Bandyopadhyay
School of Mechanical and Materials Engineering Washington State University Pullman Washington USA
1 shared publication Fan Yang
School of Mechanical and Materials Engineering, Washington State University, Pullman, WA, 99164-2920, USA
1 shared publication- Fan Yang
M3 Robotics Lab, School of Mechanical and Materials Engineering, Washington State University, Pullman, WA, 99163, USA
1 shared publication - Hongsoo Choi
Department of Biomedical Engineering University of Massachusetts Amherst Massachusetts USA
1 shared publication - Jialong Ning
School of Mechanical and Materials Engineering, Washington State University 1 , Pullman, Washington 99164-2920, USA
1 shared publication
Latest Publications
- Open Access
- 8 August 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (6)
Shock-induced transformation of nitinol shape memory alloy: Effect of stress state on transformation
Due to its numerous practical applications and intriguing phase transformation behavior, shape memory alloys (SMAs) have garnered significant research and development interests. In the past, most studies on the mechanical behavior of SMAs have been conducted under uniaxial stress loadings. Limited research on SMAs under shock loading has not provided conclusive results regarding their transformation behavior and transformation stress under such loading. Additionally, there is a lack of comprehensive understanding regarding the effects of different stress states on transformation behavior. The main objectives of this study are to address these issues. To achieve these objectives, a series of shock wave experiments were designed and conducted. Additionally, quasi-static and dynamic uniaxial stress experiments were carried out to establish a baseline for comparison. The results revealed that the transformation stress under dynamic uniaxial strain shock loading was approximately 1.92 GPa in contrast to 0.5 GPa (quasi-static) to 0.8 GPa (dynamic) observed in uniaxial stress loading. The transformation behavior exhibited noticeable rate sensitivity for both types of loading. There appeared to be a critical strain rate above which the austenite phase was driven to a metastable state. This estimated critical axial strain rate along the loading direction was approximately 2 × 103/s–4 × 103/s for uniaxial stress loading and approximately 2 × 106/s for uniaxial strain loading. The apparent high transformation stress for uniaxial strain loading can likely be attributed to a combination of high-pressure confinement and high strain rate. However, determining their relative contributions remains an open issue.
- 8 August 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (6)
Open AccessShock-induced transformation of nitinol shape memory alloy: Effect of stress state on transformation
Due to its numerous practical applications and intriguing phase transformation behavior, shape memory alloys (SMAs) have garnered significant research and development interests. In the past, most studies on the mechanical behavior of SMAs have been conducted under uniaxial stress loadings. Limited research on SMAs under shock loading has not provided conclusive results regarding their transformation behavior and transformation stress under such loading. Additionally, there is a lack of comprehensive understanding regarding the effects of different stress states on transformation behavior. The main objectives of this study are to address these issues. To achieve these objectives, a series of shock wave experiments were designed and conducted. Additionally, quasi-static and dynamic uniaxial stress experiments were carried out to establish a baseline for comparison. The results revealed that the transformation stress under dynamic uniaxial strain shock loading was approximately 1.92 GPa in contrast to 0.5 GPa (quasi-static) to 0.8 GPa (dynamic) observed in uniaxial stress loading. The transformation behavior exhibited noticeable rate sensitivity for both types of loading. There appeared to be a critical strain rate above which the austenite phase was driven to a metastable state. This estimated critical axial strain rate along the loading direction was approximately 2 × 103/s–4 × 103/s for uniaxial stress loading and approximately 2 × 106/s for uniaxial strain loading. The apparent high transformation stress for uniaxial strain loading can likely be attributed to a combination of high-pressure confinement and high strain rate. However, determining their relative contributions remains an open issue.
- 31 December 2020
- Published by SAGE Publications in Polymers and Polymer Composites
- Vol. 29 (9_suppl) , S19-S35
Effects of nanofiller geometries and interfacial properties on the mechanical performance of polymer nanocomposites—A numerical study
Many studies, experimental, theoretical, and numerical, have been done on polymer nanocomposites, but nearly all of them have focused on a particular type of material system or some specific material properties. A comprehensive understanding of this complicated material system is still quite lacking. The objective of this study is to use mesoscale finite element simulation to gain insights on the reinforcing efficiencies of different types of carbon nanofillers as distinguished by their geometries and interfacial strengths. It is demonstrated that CNT (carbon nanotube) and CNF (carbon nanofiber) have larger load carrying capacity and potentially higher reinforcing efficiency than GNP (graphite nanoplatelet) due to their larger aspect ratio and physical length. However, the higher load carrying capacity is also associated with higher interfacial stress which can lead to earlier debonding, particularly for CNT. GNP, on the other hand, has lower load carrying capacity, and is thus less sensitive to the bonding condition and less susceptible to debonding. The overall reinforcing efficiency is a manifestation of the interplay between the load carrying capacity of the filler, which is limited by filler’s geometry, and the load transfer capability at the interface, which is limited by the filler/matrix interfacial strength. This interplay is also reflected in the effects of filler orientation on reinforcing efficiency. The insights gained from this study can be used to devise a strategy for developing advanced nanocomposites, such as hybrid composites.
- 31 December 2020
- Published by SAGE Publications in Polymers and Polymer Composites
- Vol. 29 (9_suppl) , S19-S35
Effects of nanofiller geometries and interfacial properties on the mechanical performance of polymer nanocomposites—A numerical study
Many studies, experimental, theoretical, and numerical, have been done on polymer nanocomposites, but nearly all of them have focused on a particular type of material system or some specific material properties. A comprehensive understanding of this complicated material system is still quite lacking. The objective of this study is to use mesoscale finite element simulation to gain insights on the reinforcing efficiencies of different types of carbon nanofillers as distinguished by their geometries and interfacial strengths. It is demonstrated that CNT (carbon nanotube) and CNF (carbon nanofiber) have larger load carrying capacity and potentially higher reinforcing efficiency than GNP (graphite nanoplatelet) due to their larger aspect ratio and physical length. However, the higher load carrying capacity is also associated with higher interfacial stress which can lead to earlier debonding, particularly for CNT. GNP, on the other hand, has lower load carrying capacity, and is thus less sensitive to the bonding condition and less susceptible to debonding. The overall reinforcing efficiency is a manifestation of the interplay between the load carrying capacity of the filler, which is limited by filler’s geometry, and the load transfer capability at the interface, which is limited by the filler/matrix interfacial strength. This interplay is also reflected in the effects of filler orientation on reinforcing efficiency. The insights gained from this study can be used to devise a strategy for developing advanced nanocomposites, such as hybrid composites.
- 9 June 2020
- Published by Springer Nature in Medical & Biological Engineering & Computing
- Vol. 58 (8) , 1845-1872
Predictive mechanics-based model for depth of cut (DOC) of waterjet in soft tissue for waterjet-assisted medical applications
The use of waterjet technology is now prevalent in medical applications including surgery, soft tissue resection, bone cutting, waterjet steerable needles, and wound debridement. The depth of the cut (DOC) of a waterjet in soft tissue is an important parameter that should be predicted in these applications. For instance, for waterjet-assisted surgery, selective cutting of tissue layers is a must to avoid damage to deeper tissue layers. For our proposed fracture-directed waterjet steerable needles, predicting the cut depth of the waterjet in soft tissue is important to develop an accurate motion model, as well as control algorithms for this class of steerable needles. To date, most of the proposed models are only valid in the conditions of the experiments and if the soft tissue or the system properties change, the models will become invalid. The model proposed in this paper is formulated to allow for variation in parameters related to both the waterjet geometry and the tissue. In this paper, first the cut depths of waterjet in soft tissue simulants are measured experimentally, and the effect of tissue stiffness, waterjet velocity, and nozzle diameter are studied on DOC. Then, a model based on the properties of the tissue and the waterjet is proposed to predict the DOC of waterjet in soft tissue. In order to verify the model, soft tissue properties (constitutive response and fracture toughness) are measured using low strain rate compression tests, Split-Hopkinson-Pressure-Bar (SHPB) tests, and fracture toughness tests. The results show that the proposed model can predict the DOC of waterjet in soft tissue with acceptable accuracy if the tissue and waterjet properties are known. (Left) An overview of the problems of traditional steerable needles and the solutions provided by waterjet steerable needles. (A) Traditional tip-steerable needles and tip-bent needles suffer from poor curvature, especially in soft tissues. (B) Traditional steerable needles are unable to accomplish many bends because the cutting force only results from drastic tissue deformation. (C) The first step for realization of waterjet steerable needles is to understand and model the interaction between waterjet and soft tissues at the tip (predictive model for depth of cut). (D) Then, the equilibrium between shapes cut in the tissue and the straight elastic needle should be understood. (Right) Waterjet steerable needles in which the direction of the tissue fracture is contr olled by waterjet and then the flexible needle follows. The first step for waterjet steerable needle realization is to predict the depth of waterjet cut
- 9 June 2020
- Published by Springer Nature in Medical & Biological Engineering & Computing
- Vol. 58 (8) , 1845-1872
Predictive mechanics-based model for depth of cut (DOC) of waterjet in soft tissue for waterjet-assisted medical applications
The use of waterjet technology is now prevalent in medical applications including surgery, soft tissue resection, bone cutting, waterjet steerable needles, and wound debridement. The depth of the cut (DOC) of a waterjet in soft tissue is an important parameter that should be predicted in these applications. For instance, for waterjet-assisted surgery, selective cutting of tissue layers is a must to avoid damage to deeper tissue layers. For our proposed fracture-directed waterjet steerable needles, predicting the cut depth of the waterjet in soft tissue is important to develop an accurate motion model, as well as control algorithms for this class of steerable needles. To date, most of the proposed models are only valid in the conditions of the experiments and if the soft tissue or the system properties change, the models will become invalid. The model proposed in this paper is formulated to allow for variation in parameters related to both the waterjet geometry and the tissue. In this paper, first the cut depths of waterjet in soft tissue simulants are measured experimentally, and the effect of tissue stiffness, waterjet velocity, and nozzle diameter are studied on DOC. Then, a model based on the properties of the tissue and the waterjet is proposed to predict the DOC of waterjet in soft tissue. In order to verify the model, soft tissue properties (constitutive response and fracture toughness) are measured using low strain rate compression tests, Split-Hopkinson-Pressure-Bar (SHPB) tests, and fracture toughness tests. The results show that the proposed model can predict the DOC of waterjet in soft tissue with acceptable accuracy if the tissue and waterjet properties are known. (Left) An overview of the problems of traditional steerable needles and the solutions provided by waterjet steerable needles. (A) Traditional tip-steerable needles and tip-bent needles suffer from poor curvature, especially in soft tissues. (B) Traditional steerable needles are unable to accomplish many bends because the cutting force only results from drastic tissue deformation. (C) The first step for realization of waterjet steerable needles is to understand and model the interaction between waterjet and soft tissues at the tip (predictive model for depth of cut). (D) Then, the equilibrium between shapes cut in the tissue and the straight elastic needle should be understood. (Right) Waterjet steerable needles in which the direction of the tissue fracture is contr olled by waterjet and then the flexible needle follows. The first step for waterjet steerable needle realization is to predict the depth of waterjet cut
- 17 January 2008
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 18 (2) , 025037
Characterization and modeling of a piezoelectric micromachined ultrasonic transducer with a very large length/width aspect ratio
- 17 January 2008
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 18 (2) , 025037
Characterization and modeling of a piezoelectric micromachined ultrasonic transducer with a very large length/width aspect ratio