Chengning Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Chengning Zhang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Shuo Zhang
School of Mechanical Engineering, Beijing Institute of Technology, Beijing, China
5 shared publications - Nicola Bianchi
Department of Industrial Engineering, University of Padova, Padua, Italy
3 shared publications - Yongxi Yang
School of Mechanical Engineering, Beijing Institute of Technology, Beijing, China
3 shared publications Jianzhen Qu
Department of Mechanical and Vehicle Engineering Beijing Institute of Technology Beijing China
2 shared publications- Fang Wang
Shanghai Ocean University
1 shared publication - Gerd Bramerdorfer
Faculty for Engineering and Natural Sciences, Johannes Kepler University Linz, Linz, Austria
1 shared publication
Latest Publications
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (3) , 1997-2009
The Coupling Effect of Manufacturing Tolerances and Rotor Eccentricity on Cogging Torque
Manufacturing tolerances and rotor eccentricity are two typical manufacturing uncertainties in actual permanent-magnet (PM) motors, which lead to the deterioration of cogging torque. In this paper, a vector analysis method is proposed to theoretically explain the coupling mechanism of manufacturing tolerances and rotor eccentricity on the additional harmonic components (AHCs) of cogging torque. First, the AHCs of cogging torque introduced by the respective impacts of manufacturing tolerances and rotor eccentricity are summarized. Then, the coupling effect of manufacturing tolerances and rotor eccentricity on the amplitudes of these AHCs is analyzed based on the proposed method, and its efficacy is verified through finite element simulations. It is found that the coupling effects in PM motors with varying parameters and uncertain values are distinct, and the reason is discussed. Subsequently, the proposed method is used in the modification of the worst-uncertain-combination-analysis method to evaluate the robustness of cogging torque under comprehensive manufacturing uncertainties. Finally, prototypes with different combinations of uncertainties are deliberately designed and tested, and the coupling effect is verified by the experimental results.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (3) , 1997-2009
The Coupling Effect of Manufacturing Tolerances and Rotor Eccentricity on Cogging Torque
Manufacturing tolerances and rotor eccentricity are two typical manufacturing uncertainties in actual permanent-magnet (PM) motors, which lead to the deterioration of cogging torque. In this paper, a vector analysis method is proposed to theoretically explain the coupling mechanism of manufacturing tolerances and rotor eccentricity on the additional harmonic components (AHCs) of cogging torque. First, the AHCs of cogging torque introduced by the respective impacts of manufacturing tolerances and rotor eccentricity are summarized. Then, the coupling effect of manufacturing tolerances and rotor eccentricity on the amplitudes of these AHCs is analyzed based on the proposed method, and its efficacy is verified through finite element simulations. It is found that the coupling effects in PM motors with varying parameters and uncertain values are distinct, and the reason is discussed. Subsequently, the proposed method is used in the modification of the worst-uncertain-combination-analysis method to evaluate the robustness of cogging torque under comprehensive manufacturing uncertainties. Finally, prototypes with different combinations of uncertainties are deliberately designed and tested, and the coupling effect is verified by the experimental results.
- 4 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 37 (08858969) , 1
A computationally efficient surrogate model based robust optimization for permanent magnet synchronous machines
One of the main obstacles to the robust optimization for permanent magnet machines is the high computational burden, which is mainly caused by the robustness evaluation process considering the manufacturing uncertainties. In this paper, a sequential sampling Kriging model is adopted to estimate the design robustness, and the problem of high-dimensional variables for the surrogate model due to uncertainties is avoided through adopting the worst-case based approach. To further reduce the number of finite element analyses (FEA) required for constructing a metamodel, a multi-points sequential sampling process with a two-step optimization oriented surrogate model updating algorithm is proposed. Compared with the FEA directly based robust optimization in previous work, similar Pareto Fronts are achieved by adopting the meta-model proposed algorithm but the overall run time reduced by 75%. In the end, an optimization problem for a 1.2 kW motor is considered by applying the proposed algorithm, and two prototypes with deliberately designed tolerances, imitating the worst-case scenarios in the real world, are manufactured. The worst-case torque ripple is reduced from 7.6% to 4.8% after optimizing, and this verifies the efficacy of the proposed algorithm.
- 4 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 37 (08858969) , 1
A computationally efficient surrogate model based robust optimization for permanent magnet synchronous machines
One of the main obstacles to the robust optimization for permanent magnet machines is the high computational burden, which is mainly caused by the robustness evaluation process considering the manufacturing uncertainties. In this paper, a sequential sampling Kriging model is adopted to estimate the design robustness, and the problem of high-dimensional variables for the surrogate model due to uncertainties is avoided through adopting the worst-case based approach. To further reduce the number of finite element analyses (FEA) required for constructing a metamodel, a multi-points sequential sampling process with a two-step optimization oriented surrogate model updating algorithm is proposed. Compared with the FEA directly based robust optimization in previous work, similar Pareto Fronts are achieved by adopting the meta-model proposed algorithm but the overall run time reduced by 75%. In the end, an optimization problem for a 1.2 kW motor is considered by applying the proposed algorithm, and two prototypes with deliberately designed tolerances, imitating the worst-case scenarios in the real world, are manufactured. The worst-case torque ripple is reduced from 7.6% to 4.8% after optimizing, and this verifies the efficacy of the proposed algorithm.
- Open Access
- 21 March 2021
- Published by Institution of Engineering and Technology (IET) in IET Electric Power Applications
- Vol. 15 (6) , 681-695
Improved multiple vector model predictive torque control of permanent magnet synchronous motor for reducing torque ripple
The two‐voltage‐vector (2VV) model predictive torque control (MPTC) has been widely discussed and compared to the conventional single‐voltage‐vector (1VV) MPTC in permanent magnet synchronous motor drive applications, where it was shown to have quick response and low torque ripple. An improved 2VV‐MPTC is set forth based on extended control set. In the proposed approach, the reference voltage vector is calculated using the established torque and flux deadbeat control and optimal calculation of the duty cycles. Moreover, to further improve the torque performance, the proposed algorithm is extended to three‐voltage vector (3VV), which is shown to achieve even better performance. Experimental results demonstrate that the proposed 2VV and 3VV‐MPTC algorithms have better computation efficiency and can significantly reduce torque ripple compared to the previous methods.
- 21 March 2021
- Published by Institution of Engineering and Technology (IET) in IET Electric Power Applications
- Vol. 15 (6) , 681-695
Open AccessImproved multiple vector model predictive torque control of permanent magnet synchronous motor for reducing torque ripple
The two‐voltage‐vector (2VV) model predictive torque control (MPTC) has been widely discussed and compared to the conventional single‐voltage‐vector (1VV) MPTC in permanent magnet synchronous motor drive applications, where it was shown to have quick response and low torque ripple. An improved 2VV‐MPTC is set forth based on extended control set. In the proposed approach, the reference voltage vector is calculated using the established torque and flux deadbeat control and optimal calculation of the duty cycles. Moreover, to further improve the torque performance, the proposed algorithm is extended to three‐voltage vector (3VV), which is shown to achieve even better performance. Experimental results demonstrate that the proposed 2VV and 3VV‐MPTC algorithms have better computation efficiency and can significantly reduce torque ripple compared to the previous methods.
- 2 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 36 (3) , 2502-2513
Torque Ripple Reduction Method for Permanent Magnet Synchronous Machine Drives With Novel Harmonic Current Control
Torque ripple reduction has become an active research area for permanent magnet synchronous machine (PMSM) drives. This paper presents a novel torque ripple reduction method based on harmonic current control. In the proposed method, the optimal harmonic current solution based on the torque ripple model with minimum stator resistive loss is derived in the rotor reference frame (RRF). The optimal harmonic currents are injected by the proposed harmonic current controller (HCC), wherein the magnitude of harmonic currents are defined as controller variables. To estimate the harmonic currents, the proposed method also utilizes the least mean square (LMS) based adaptive filter (AF), wherein the coefficients are defined as feedback to the proposed HCC. The proposed methodology is demonstrated using both simulations and experiments and is verified to reduce torque ripples of PMSM drives over a wide range of speeds.
- 2 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 36 (3) , 2502-2513
Torque Ripple Reduction Method for Permanent Magnet Synchronous Machine Drives With Novel Harmonic Current Control
Torque ripple reduction has become an active research area for permanent magnet synchronous machine (PMSM) drives. This paper presents a novel torque ripple reduction method based on harmonic current control. In the proposed method, the optimal harmonic current solution based on the torque ripple model with minimum stator resistive loss is derived in the rotor reference frame (RRF). The optimal harmonic currents are injected by the proposed harmonic current controller (HCC), wherein the magnitude of harmonic currents are defined as controller variables. To estimate the harmonic currents, the proposed method also utilizes the least mean square (LMS) based adaptive filter (AF), wherein the coefficients are defined as feedback to the proposed HCC. The proposed methodology is demonstrated using both simulations and experiments and is verified to reduce torque ripples of PMSM drives over a wide range of speeds.
- 12 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 35 (4) , 2116-2128
Methods to Reduce the Computational Burden of Robust Optimization for Permanent Magnet Motors
One of the main obstacles to applying the robust optimization for the permanent magnet motor might be the high computational burden, which is mainly caused by the robustness evaluation considering the manufacturing uncertainties. In this paper, efforts are made to speed up the process of robust optimization, from the aspects of reducing the computational cost and avoiding the computing resources being wasted. Firstly, several widely used methods, aiming to identify the worst-case performance under uncertainties, are examined and compared. And the efficient worst-uncertain-combination-analysis (WUCA) method is consequently adopted to significantly reduce the computational cost of robustness evaluation. From another aspect, the parameter rounding (PR) operation is inevitable due to the constraint of manufacturing accuracy, but its adverse effects on the optimization are often ignored. It is found that parts of the computing resources might be wasted during the optimization. A new PR during the calculation (PRDC) method is proposed and incorporated into the process of robust optimization. Compared with the conventional one, the similarly optimal results can be achieved with the computational time reduced by approximately 11% in the PRDC modified robust optimization.
- 12 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 35 (4) , 2116-2128
Methods to Reduce the Computational Burden of Robust Optimization for Permanent Magnet Motors
One of the main obstacles to applying the robust optimization for the permanent magnet motor might be the high computational burden, which is mainly caused by the robustness evaluation considering the manufacturing uncertainties. In this paper, efforts are made to speed up the process of robust optimization, from the aspects of reducing the computational cost and avoiding the computing resources being wasted. Firstly, several widely used methods, aiming to identify the worst-case performance under uncertainties, are examined and compared. And the efficient worst-uncertain-combination-analysis (WUCA) method is consequently adopted to significantly reduce the computational cost of robustness evaluation. From another aspect, the parameter rounding (PR) operation is inevitable due to the constraint of manufacturing accuracy, but its adverse effects on the optimization are often ignored. It is found that parts of the computing resources might be wasted during the optimization. A new PR during the calculation (PRDC) method is proposed and incorporated into the process of robust optimization. Compared with the conventional one, the similarly optimal results can be achieved with the computational time reduced by approximately 11% in the PRDC modified robust optimization.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Analysis of stator winding inter-turn short circuit fault of PMSM for electric vehicle based on finite element simulation
This paper analyzes the characteristics of the inter-turn short circuit fault based on the permanent magnet synchronous motor (PMSM) structure algorithm. The finite element model of the PMSM inter-turn short circuit fault is established for the electric vehicle application. Simulations are performed on healthy motor and faulty motor with different severity of short circuit faults and operate modes. Then analyzes the influences of short circuit fault on the magnetic field and various parameters of motors and extracts feature vector for detecting inter-turn short circuit fault. It also proves that the method of finite element analysis (FEA) can provide a scientific and accurate basis for studying on inter-turn short circuit fault. This research method makes a foundation for diagnosis of other faults of PMSM for electric vehicle.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Analysis of stator winding inter-turn short circuit fault of PMSM for electric vehicle based on finite element simulation
This paper analyzes the characteristics of the inter-turn short circuit fault based on the permanent magnet synchronous motor (PMSM) structure algorithm. The finite element model of the PMSM inter-turn short circuit fault is established for the electric vehicle application. Simulations are performed on healthy motor and faulty motor with different severity of short circuit faults and operate modes. Then analyzes the influences of short circuit fault on the magnetic field and various parameters of motors and extracts feature vector for detecting inter-turn short circuit fault. It also proves that the method of finite element analysis (FEA) can provide a scientific and accurate basis for studying on inter-turn short circuit fault. This research method makes a foundation for diagnosis of other faults of PMSM for electric vehicle.