JDJakub Dömény

Jakub Dömény

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jakub Dömény has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Combination of Chemical Modification and Densification Processes to Improve the Sorption and Dimensional Stability of Wood

    by Štěpán Beránek, Martin Brabec, Charalampos Lykidis, Jakub Dömény

    Due to the limited availability of durable tropical timber species, the development and production of chemically modified wood materials are expanding. Past research has investigated chemical reactions between the hydroxyl groups of wood and carboxylic acid anhydrides. Tropical species exhibit excellent durability, mechanical properties, and low water absorption, making it difficult for domestic species to compete with them. Therefore, this study employed a combination of chemical modification processes (acetylation and propionylation) and densification on two of the most widespread domestic species: European beech (Fagus sylvatica L.) and Norway spruce (Picea abies (L.) H. Karst). The modified samples were compared in terms of water-related properties, specifically sorption and dimensional stability. Both chemical modification methods, when combined with densification, positively influenced the monitored sorption and dimensional characteristics compared to non-densified samples. Unlike the reference samples, the modified domestic species exhibited water-related properties and dimensional stability comparable to the selected exotic species, Jatoba (Hymenaea courbaril). While Jatoba samples generally showed higher density values, densified propionylated beech and reference spruce were statistically comparable, and densified reference beech actually surpassed the density values significantly.

  • Open Access

    The Weathering of the Beech and Spruce Wood Impregnated with Pigmented Linseed Oil

    by Fanni Fodor, Jakub Dömény, Péter György Horváth, Barbora Pijáková, Jan Baar

    This research aimed to examine the effects of a deep impregnation technique (Royal process) and surface coating using a linseed oil-based product, enhanced with small amounts of brown and grey pigments, on the natural and artificial weathering of wood. The treated and reference samples underwent natural weathering for five years and artificial weathering for 1900 h. Changes in color and surface roughness were assessed during weathering. For the artificially weathered samples, liquid water absorption was measured both before and after exposure. The impregnated and coated samples gradually lost their brown color, turning grey over time. More pronounced differences were observed during natural weathering, with the coated samples showing greater structural changes on the wood surface. In contrast, impregnated samples slowed down structural alterations compared to the reference samples. Both treatments effectively reduced water absorption before weathering, although this effect diminished after exposure. The treatments did not significantly impact the fire resistance of spruce and beechwood.


  • Open Access

    Development of a Continuous Wood Surface Charge Detection Device

    by Lena Maria Leiter, Roman Myna, Jakub Domeny, Rupert Wimmer

    Almost all woodworking processes involve mechanical friction and contact electrification, i.e. triboelectrification, between the wood surface and the woodworking tool. An electric charge is transferred from one solid surface to another when two materials come into contact with each other. Currently, there are no continuous inline-capable electrical surface charge measuring devices. The goal of this work was to create a measurement setup that can be used with a variety of woodworking processes. The proposed continuous surface charge detection (ConSurChaD) device connects an electric fieldmeter (EFM) to a Faraday cage-style measuring box. Individual elements of the box can be mounted or dismounted to fit various wood working processes. The application of electrostatic induction principles permitted quantification of the electrostatic surface charge by measuring the accumulated electric field strength generated, expressed in kV/m. The device was compared to a reference method using a commercial discontinuous detection approach. Measurements were made simultaneously using an electrostatic voltmeter, a hand-held instrument that measured the surface charge in volts. The validation confirmed the accuracy of the ConSurChaD device ensuring the applicability for continuous measurement of electrostatic surface charges. This approach allows for a more efficient and targeted application of triboelectrification to wood surfaces, leading to improved surface coatings and other enhancements.


  • Open Access

    Moisture Sorption of Wood Surfaces Modified by One-Sided Carbonization as an Alternative to Traditional Façade Coatings

    by Maija Kymäläinen, Jakub Dömény, Lauri Rautkari

    Surface carbonization, or charring, of wooden cladding boards is a promising, low impact process that can substitute inorganic coatings. The char surface is inert and hydrophobic and possibly a long-lasting solution for exterior uses. To determine the performance of surface-charred wood, several sorption experiments were established. Sapwood of two hardwoods (aspen, birch) and two softwoods (pine, spruce) were used as the experimental material, modified by contact charring and gas flame charring, including surfaces coated with oil for further protection. The results showed that flame charring modification is equal to a double layer of acrylic paint on primer in terms of permeability on all wood species, with higher moisture exclusion efficiency at high relative humidity. Contact charring modification presented much improved properties in comparison to both flame charring and acrylic paint in all implemented sorption experiments, but the dimensional stability was poor with strong cupping in wetting. However, hardwoods and especially birch exhibited less dimensional distortion than the other investigated species, and oiling further reduced the cupping. The contact charring modification produced more repeatable results with less impact from substrate and all wood species benefitted, whereas the flame charring modification is more dependent on inherent properties of the wood species, and does not seem to suit aspen as well as birch, and pine as well as spruce, although oiling affected the observed results.


  • Open Access

    Artificial Weathering of Contact-Charred Wood—The Effect of Modification Duration, Wood Species and Material Density

    by Maija Kymäläinen, Tinh Sjökvist, Jakub Dömény, Lauri Rautkari

    A relevant issue with charred exteriors is the inconsistency of the result, which makes service life predictions complicated. Contact charring enables the creation of a very evenly modified surface with accurate control of temperature and modification time, but the weathering properties are questionable. This paper evaluated the effect of the modification time relative to char layer and transition zone thickness, wood species and material density in an artificial weathering test. The results revealed higher color stability in connection to longer modification time, but also an increase in the cracked surface area. Cracking was heavily dependent on the modification regime and increased with increasing char and transition zone thicknesses. Dense spruce had the highest color stability with the most severe modification regime, but char layer thickness varied more than on other wood types. Furthermore, species-dependent cracking patterns affected the final result as the small-scale flaking experienced by birch increased the washing off of char. It is likely an even higher modification temperature with a shorter modification time is needed to produce sufficient weathering resistance suitable for exterior uses.


  • Effect of microwave and steam treatment on the thermo-hygro-plasticity of beech wood

    by Jakub Dömény, Martin Brabec, Radim Rousek, Lauri Rautkari, Petr Čermák

    The effects of microwave and steam treatment were analyzed relative to the immediate (thermo-hygro-plasticity) and post-assessed (permanent changes) properties of wood. The study was conducted using European beech (Fagus sylvatica L.) standard and 1.5 times up-scaled (only for microwave-heated and reference samples) bending specimens tested in a static three-point loading mode. The specimens were plasticized by heat and moisture (1) separately and (2) simultaneously by heating moist specimens using (i) various microwave regimes in continuous mode, and (ii) heated saturated steam in discontinuous mode. Oven-dried specimens tested at 20 °C served as references. The thermo-hygro-plasticity was studied immediately after treatment, whereas the permanent changes were assessed after oven-drying of plasticized specimens to 0% moisture content. Permanent structural changes were analyzed using scanning electron microscopy. Microwave treatment increased the plasticity of wood (decreasing the modulus of elasticity by 70%) comparably to steam treatment, when the output moisture content was 30% or higher. A similar degree of plasticity was found in up-scaled specimens heated by microwaves. Further analyses confirmed that microwave treatment did not cause any permanent damage to wood structure or reduce mechanical performance. The results showed that microwave treatment is an efficient alternative to steaming when plasticizing moist wood.


  • Open Access

    Surface Characteristics of One-Sided Charred Beech Wood

    by Dita Machová, Anna Oberle, Lucie Zárybnická, Jakub Dohnal, Vít Šeda, Jakub Dömény, Veronika Vacenovská, Michal Kloiber, Jan Pěnčík, Jan Tippner, et al.

    The aim of this paper was to analyze selected properties of beech wood (Fagus sylvatica L.) treated by one-sided surface charring. Specimens were one-side charred with a hot plate using several time-temperature combinations (from 200 to 400 °C). Characteristics such as colour, discoloration, surface roughness, fire resistance, total carbohydrate content at several wood layers and decay resistance were evaluated. Surface charring was applied to the radial and tangential surfaces. Colour measurements showed that the surface of the wood turned grey due to charring. In addition to colour measurements, other experiments showed significant differences between radial and tangential specimens due to their different structures. The higher the temperature used in treating them, the lower the roughness values for radial specimens, while the trend for tangential specimens was the opposite. A smoother surface is more fire resistant, so radial specimens are generally better in this regard. Tangential specimens are more susceptible during preparation to forming cracks that impair flame resistance because a continuous protective densified layer is not formed. The determination of total carbohydrates revealed significant changes at various wood depths after surface charring. These changes were more predictable in radial specimens due to the annual ring orientation, because each layer consisted of a similar earlywood/latewood ratio. Finally, when decay resistance was assessed, weight loss was found to be lower in all specimens than in the references. The results suggest that charring at a particular combination of temperature and time improved the investigated properties of the surface-modified beech.


  • Open Access

    Effect of One-Sided Surface Charring of Beech Wood on Density Profile and Surface Wettability

    by Vít Šeda, Dita Machová, Jakub Dohnal, Jakub Dömény, Lucie Zárybnická, Anna Oberle, Veronika Vacenovská, Petr Čermák

    One-sided surface charred European beech wood (Fagus sylvatica L.) was studied. Radial and tangential specimens of dimensions of 50 × 25 × 350 mm were one-sided surface charred at 200, 250, 300, 350, and 400 °C for various times using a contact heating system. Specimens of dimensions of 50 × 25 × 50 mm3 were prepared for treatment intensity analysis and its effect on surface wettability. Density profiles of the radial and tangential charred specimens were determined using X-ray densitography with a resolution of 0.05 mm. The wettability of the one-sided surface charred wood specimens was analyzed via contact angle, measured using the sessile drop method and determined over 10 to 150 s. The oven-dried specimens were partially submerged in water and water uptake was recorded after 2, 4, 6, 8, 10, 48, and 72 h according to EN-927-5. The surface density of the radial specimen groups charred at 200 °C for 6 min and 250 °C for 4 min decreased by about 4.5 to 8.2%. With increasingly severe charring, the surface density decreased by about 15.5 to 33.5%. A mild charring process produced a surface charred layer of approx. 2 mm, while higher temperatures and longer times affected the density up to 4–6 mm beneath the surface. Differences were found between the water uptake of the radial and tangential charred beech specimens. The most significant decrease of 56% in water uptake was recorded for the radial group prepared at 200 °C for 20 min after floating in water for 72 h. Water uptake in the radial groups modified at 250 °C for 4 and 6 min after 72 h decreased by 38% and 36%, respectively. The tangential groups did not show any statistically significant decrease. The average water uptake of the groups charred at 200 °C for 20 min, 350 °C for 2 min and 400 °C for 1 min was greater than that of the reference; the variability of the measured data was significantly greater due to the highly anisotropic character of the tangential specimens. Micro cracks were also visible on the surface. Concluding from the results of this study, one-sided surface charred beech wood exhibits increased potential in terms of wood–water related properties when a temperature range of 200–400 °C is applied.


  • Open Access

    Possibilities of Decreasing Hygroscopicity of Resonance Wood Used in Piano Soundboards Using Thermal Treatment

    by Petr Zatloukal, Pavlína Suchomelová, Jakub Dömény, Tadeáš Doskočil, Ginevra Manzo, Jan Tippner

    This article presents the possibilities of decreasing moisture sorption properties via thermal modification of Norway spruce wood in musical instruments. The 202 resonance wood specimens that were used to produce piano soundboards have been conditioned and divided into three density groups. The first specimen group had natural untreated properties, the second was thermally treated at 180 °C, and the third group was treated at 200 °C. All specimens were isothermally conditioned at 20 °C with relative humidity values of 40, 60, and 80%. The equilibrium moisture content (EMC), swelling, and acoustical properties, such as the longitudinal dynamic modulus (E’L), bending dynamic modulus (Eb), damping coefficient (tan δ), acoustic conversion efficiency (ACEL), and relative acoustic conversion efficiency (RACEL) were evaluated on every moisture content level. Treatment at 180 °C caused the EMC to decrease by 36% and the volume swelling to decrease by 9.9%. Treatment at 200 °C decreased the EMC by 42% and the swelling by 39.6%. The 180 °C treatment decreased the value of the longitudinal sound velocity by 1.6%, whereas the treatment at 200 °C increased the velocity by 2.1%. The acoustical properties EL′, Eb, ACEL, and RACEL were lower due to the higher moisture content of the samples, and only the tanδ increased. Although both treatments significantly affected the swelling and EMC, the treatment at 180 °C did not significantly affect the acoustical properties.


  • One-sided surface charring of beech wood

    by Petr Čermák, Aleš Dejmal, Zuzana Paschová, Maija Kymäläinen, Jakub Dömény, Martin Brabec, Dominik Hess, Lauri Rautkari