Tracy C. Becker
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tracy C. Becker has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Yu Bao
School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, China
4 shared publications Mao Cheng
Department of Civil Environmental Engineering University of California Berkeley USA
3 shared publications- Ahmed M. Abdelmaksoud
Dalhousie Univ
2 shared publications - Georgios P. Balomenos
School of Science and Technology, Hellenic Open University, Patras, Greece
2 shared publications Hiroki Hamaguchi
Takenaka Research and Development Institute Chiba Japan
2 shared publicationsStephen A. Mahin
Department of Civil and Environmental Engineering University of California Berkeley CA USA
2 shared publications
Latest Publications
- Open Access
- 19 March 2026
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 55 (9) , 1828-1844
Quantifying Model Selection Uncertainty in Structural Analysis: Methodology and Application
With increasing focus on complex engineering systems under rare events, computational models are critical for predictions due to the scarcity or absence of data. However, selecting an appropriate model can be challenging. Using a single model without available test calibration could result in significant bias in performance predictions. A case study of a steel moment frame reveals substantial discrepancies between predictions given different model selections, particularly under increasing ground motion intensities. To address this challenge, this paper proposes a model averaging methodology based on the logic tree approach to incorporate multiple models and capture their full spectrum of potential outcomes. A combination of dimensionality reduction techniques and Bayesian inference is employed to determine the weight of each model candidate. The weight is represented as a Dirichlet prior, which is determined by incorporating expert knowledge and structural component testing results. This approach enables the assignment of a more informative prior even when no observational data is available, while also leaving room for updating the prior if data becomes available. By leveraging model averaging and uncertainty propagation techniques to address model uncertainty in structural analysis, a response interval is then generated for the quantity of interest. This methodology provides a more comprehensive, informative, and feasible assessment to address model selection uncertainty to improve predictive capabilities and enhance the ability of engineers to treat design in a probabilistic manner. In its present formulation, however, the approach is applicable to precollapse response regimes where finite response quantities can be defined and does not explicitly address collapse‐state realizations.
- 19 March 2026
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 55 (9) , 1828-1844
Open AccessQuantifying Model Selection Uncertainty in Structural Analysis: Methodology and Application
With increasing focus on complex engineering systems under rare events, computational models are critical for predictions due to the scarcity or absence of data. However, selecting an appropriate model can be challenging. Using a single model without available test calibration could result in significant bias in performance predictions. A case study of a steel moment frame reveals substantial discrepancies between predictions given different model selections, particularly under increasing ground motion intensities. To address this challenge, this paper proposes a model averaging methodology based on the logic tree approach to incorporate multiple models and capture their full spectrum of potential outcomes. A combination of dimensionality reduction techniques and Bayesian inference is employed to determine the weight of each model candidate. The weight is represented as a Dirichlet prior, which is determined by incorporating expert knowledge and structural component testing results. This approach enables the assignment of a more informative prior even when no observational data is available, while also leaving room for updating the prior if data becomes available. By leveraging model averaging and uncertainty propagation techniques to address model uncertainty in structural analysis, a response interval is then generated for the quantity of interest. This methodology provides a more comprehensive, informative, and feasible assessment to address model selection uncertainty to improve predictive capabilities and enhance the ability of engineers to treat design in a probabilistic manner. In its present formulation, however, the approach is applicable to precollapse response regimes where finite response quantities can be defined and does not explicitly address collapse‐state realizations.
- 1 October 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 151 (10)
Cyclic Demands on Solar Structural Joints under Wind Loading
- 1 October 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 151 (10)
Cyclic Demands on Solar Structural Joints under Wind Loading
- 19 October 2024
- Published by Elsevier in Engineering Structures
- Vol. 322
Design of isolated buildings to achieve targeted collapse limits through Gaussian process modeling
- 19 October 2024
- Published by Elsevier in Engineering Structures
- Vol. 322
Design of isolated buildings to achieve targeted collapse limits through Gaussian process modeling
- Open Access
- 21 May 2024
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 53 (10) , 3071-3092
Selective online model updating in hybrid simulation of a full‐scale steel moment frame
This study presents the implementation of an online model updating algorithm within a full‐scale hybrid simulation (HS) of a six story, four bay steel moment frame. The experimental substructure consists of a cruciform subassembly generating critical data on the nonlinear behavior of the first story column and two beams with reduced beam sections (RBSs) on each side. The updating algorithm focuses on the modeling parameters of plastic hinge elements representing the RBSs in the numerical model. A smooth plasticity model is utilized for beam plastic hinges with updating parameters identified from on‐line experimental data through a modified version of the unscented Kalman filter. The HS shows that the numerical beam hinges based on simple hysteretic model with updated parameters are able to capture the characteristic behavior observed in experiments. Due to fracture of beam flanges is observed in the experiments, a selective updating concept is proposed to allow for updating multiple numerical components accounting for asymmetric behavior and variability in the response. The selective updating method is validated through virtual HSs that are better able to identify and isolate the effects of fracture and other behavioral characteristics. The combination of results from physical and virtual tests highlights the benefits of model updating on the local and overall system‐level response.
- 21 May 2024
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 53 (10) , 3071-3092
Open AccessSelective online model updating in hybrid simulation of a full‐scale steel moment frame
This study presents the implementation of an online model updating algorithm within a full‐scale hybrid simulation (HS) of a six story, four bay steel moment frame. The experimental substructure consists of a cruciform subassembly generating critical data on the nonlinear behavior of the first story column and two beams with reduced beam sections (RBSs) on each side. The updating algorithm focuses on the modeling parameters of plastic hinge elements representing the RBSs in the numerical model. A smooth plasticity model is utilized for beam plastic hinges with updating parameters identified from on‐line experimental data through a modified version of the unscented Kalman filter. The HS shows that the numerical beam hinges based on simple hysteretic model with updated parameters are able to capture the characteristic behavior observed in experiments. Due to fracture of beam flanges is observed in the experiments, a selective updating concept is proposed to allow for updating multiple numerical components accounting for asymmetric behavior and variability in the response. The selective updating method is validated through virtual HSs that are better able to identify and isolate the effects of fracture and other behavioral characteristics. The combination of results from physical and virtual tests highlights the benefits of model updating on the local and overall system‐level response.
- 4 January 2024
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 53 (3) , 1398-1415
Application of model updating to a large‐scale hybrid simulation
Model updating can enhance hybrid simulation by utilizing the experimental data from the physically tested substructure to update the parameters of like‐components in the numerical substructure throughout the test, improving the overall accuracy and reducing the extent of the experimental setup. Identifying and updating parameters can be challenging, especially when coupling between degrees of freedom (DOF) must be considered or the specimen experiences loading scenarios which result in newly observed behavior. To explore the performance of model updating under these challenging conditions, a large‐scale hybrid simulation was conducted using a model of a major toll bridge with seismic isolation lead rubber bearings (LRB). One LRB is physically tested considering axial, shear, and rotational loading, while the remainder of the bearings are simulated and updated with a phenomenological model within the numerical substructure. A weighted adaptive constrained unscented Kalman filter is applied as the online model updating algorithm. The study explored the effect of learning over different loading patterns, the selection of initial model parameters, and the selection of the physically tested substructure. The improvement of numerical model hysteresis performance accuracy of the force prediction demonstrates the benefits of model updating in large‐scale hybrid simulation.
- 4 January 2024
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 53 (3) , 1398-1415
Application of model updating to a large‐scale hybrid simulation
Model updating can enhance hybrid simulation by utilizing the experimental data from the physically tested substructure to update the parameters of like‐components in the numerical substructure throughout the test, improving the overall accuracy and reducing the extent of the experimental setup. Identifying and updating parameters can be challenging, especially when coupling between degrees of freedom (DOF) must be considered or the specimen experiences loading scenarios which result in newly observed behavior. To explore the performance of model updating under these challenging conditions, a large‐scale hybrid simulation was conducted using a model of a major toll bridge with seismic isolation lead rubber bearings (LRB). One LRB is physically tested considering axial, shear, and rotational loading, while the remainder of the bearings are simulated and updated with a phenomenological model within the numerical substructure. A weighted adaptive constrained unscented Kalman filter is applied as the online model updating algorithm. The study explored the effect of learning over different loading patterns, the selection of initial model parameters, and the selection of the physically tested substructure. The improvement of numerical model hysteresis performance accuracy of the force prediction demonstrates the benefits of model updating in large‐scale hybrid simulation.
- 1 July 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 149 (7)
Sliding versus Rubber Bearings: Exploring the Difference in Collapse Probability
- 1 July 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 149 (7)
Sliding versus Rubber Bearings: Exploring the Difference in Collapse Probability
- 2 June 2023
- Published by Elsevier in Engineering Structures
- Vol. 290
Lumped mass models for use in predicting collapse of an isolated building
- 2 June 2023
- Published by Elsevier in Engineering Structures
- Vol. 290
Lumped mass models for use in predicting collapse of an isolated building
- 1 February 2022
- Published by Elsevier in Engineering Structures
- Vol. 252, 113649
Parameterized models for prediction of lifetime bearing demands
- 1 February 2022
- Published by Elsevier in Engineering Structures
- Vol. 252, 113649
Parameterized models for prediction of lifetime bearing demands
- 1 October 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 26 (10) , 04021072
Parameterized Logistic Models for Bridge Inspection and Maintenance Scheduling
Proper inspection and maintenance schedules are integral to bridge functionality and safety; however, they also pose challenges in light of budget and resource limitations. As such, bridge management systems (BMSs) are always concerned with finding the best deterioration and maintenance models to optimize scheduling. The current work proposes parameterized logistic models that can capture bridge deterioration and the effect of maintenance interventions. Given a handful of easy-to-track bridge parameters, such as age, time since last major maintenance, and location, the proposed models predict the probability of a bridge (or group of bridges) to need repair throughout its service life. Combined with the appropriate probability threshold, obtained from life-cycle cost analysis, this allows for the optimization of inspection frequency and helps in maintenance planning. The results indicate that the proposed models predict the bridge condition more accurately compared to the Markov Chains models adopted by many North American BMSs. Finally, the application of the parameterized logistic models is demonstrated through a case study.
- 1 October 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 26 (10) , 04021072
Parameterized Logistic Models for Bridge Inspection and Maintenance Scheduling
Proper inspection and maintenance schedules are integral to bridge functionality and safety; however, they also pose challenges in light of budget and resource limitations. As such, bridge management systems (BMSs) are always concerned with finding the best deterioration and maintenance models to optimize scheduling. The current work proposes parameterized logistic models that can capture bridge deterioration and the effect of maintenance interventions. Given a handful of easy-to-track bridge parameters, such as age, time since last major maintenance, and location, the proposed models predict the probability of a bridge (or group of bridges) to need repair throughout its service life. Combined with the appropriate probability threshold, obtained from life-cycle cost analysis, this allows for the optimization of inspection frequency and helps in maintenance planning. The results indicate that the proposed models predict the bridge condition more accurately compared to the Markov Chains models adopted by many North American BMSs. Finally, the application of the parameterized logistic models is demonstrated through a case study.
- 1 July 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 147 (7) , 04021101
Stiffness of Rubber Bearings Considering Nonstandard Top and Bottom Boundary Conditions
Typical installations of seismic isolation assume flexurally rigid end conditions; however, in retrofit scenarios where bearings may be placed at the tops of columns or in bridges with tall piers, some rotation may occur at the boundaries. Very few experimental programs have explored the effects of these flexible boundary conditions; however, none have applied cyclic rotation at both top and bottom end plates in combination with cyclic horizontal demands, which is representative of potential loading with flexible boundary conditions. To address this gap, an experimental program on quarter-scale column-top mounted natural and lead-core rubber bearings was conducted. Rotations were applied at both the top and bottom bearing end-plates to investigate the impact of nonzero rotation boundary conditions on key design assumptions such as horizontal stiffness and rotational stiffness, and how these effects change with axial load beyond that for zero-rotation cases. Flexible boundary conditions reduce the horizontal stiffness, and the rotation-induced reduction in horizontal stiffness is dependent on the sum of the rotation at the ends, regardless of the rotation of one bearing end-plate with respect to the other. This rotation-induced decrease in stiffness is also dependent on axial load, with larger axial load leading to a higher dependency on rotation. Last, while it is known that the overlapping area method used for stability limits is conservative for rigid boundary conditions, this was shown to be true even for the bearing with a moderate shape factor ( ) when supported by a flexible column. However, the overlapping area method was not conservative for the bearing tested with low shape factor ( ), which exhibited a tangential stiffness of zero at an axial load less than the stability limit from this method.- 1 July 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 147 (7) , 04021101
Stiffness of Rubber Bearings Considering Nonstandard Top and Bottom Boundary Conditions
Typical installations of seismic isolation assume flexurally rigid end conditions; however, in retrofit scenarios where bearings may be placed at the tops of columns or in bridges with tall piers, some rotation may occur at the boundaries. Very few experimental programs have explored the effects of these flexible boundary conditions; however, none have applied cyclic rotation at both top and bottom end plates in combination with cyclic horizontal demands, which is representative of potential loading with flexible boundary conditions. To address this gap, an experimental program on quarter-scale column-top mounted natural and lead-core rubber bearings was conducted. Rotations were applied at both the top and bottom bearing end-plates to investigate the impact of nonzero rotation boundary conditions on key design assumptions such as horizontal stiffness and rotational stiffness, and how these effects change with axial load beyond that for zero-rotation cases. Flexible boundary conditions reduce the horizontal stiffness, and the rotation-induced reduction in horizontal stiffness is dependent on the sum of the rotation at the ends, regardless of the rotation of one bearing end-plate with respect to the other. This rotation-induced decrease in stiffness is also dependent on axial load, with larger axial load leading to a higher dependency on rotation. Last, while it is known that the overlapping area method used for stability limits is conservative for rigid boundary conditions, this was shown to be true even for the bearing with a moderate shape factor ( ) when supported by a flexible column. However, the overlapping area method was not conservative for the bearing tested with low shape factor ( ), which exhibited a tangential stiffness of zero at an axial load less than the stability limit from this method.