Qi Fan
Qi Fan has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Mengxiang Liu
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
4 shared publications - Yan Su
Nanjing University of Science and Technology
4 shared publications - Yi Zhou
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China
4 shared publications - Chen Lin
School of Technology, Beijing Forestry University, Beijing, China
3 shared publications - Jian Zhao
Shanghai Jiao Tong University
2 shared publications Benhao Huang
Shanghai Jiao Tong University
1 shared publication
Latest Publications
- 1 January 2022
- Published by Springer Nature
- p. 731-741
Reliable Transport Mechanism Based on Multi-queue Scheduling
- 1 January 2022
- Published by Springer Nature
- p. 731-741
Reliable Transport Mechanism Based on Multi-queue Scheduling
- 21 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (3) , 2282-2291
A MEMS Rate-Integrating Gyroscope (RIG) With In-Run Automatic Mode-Matching
Toward the objective of eliminating the angle error and rate threshold of the rate integrating gyroscope (RIG) caused by stiffness asymmetry, a novel in-run automatic mode-matching method is presented in this paper. Although other manual mode-matching methods can reduce the stiffness asymmetry temporarily, the environmental factors will interfere the manual calibration. Combined with virtual rotation, the processing circuits obtain the resonant frequencies of RIG operation modes and a controller is used to reduce the frequency difference. Meanwhile, an innovative method is proposed for RIG angle error analysis, avoiding the drawbacks of the traditional analysis methods. An FPGA based platform using a MEMS disk resonator is tested and the angle error is reduced to 1 degree compared with the manual calibration result 6.1 degrees.
- 21 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (3) , 2282-2291
A MEMS Rate-Integrating Gyroscope (RIG) With In-Run Automatic Mode-Matching
Toward the objective of eliminating the angle error and rate threshold of the rate integrating gyroscope (RIG) caused by stiffness asymmetry, a novel in-run automatic mode-matching method is presented in this paper. Although other manual mode-matching methods can reduce the stiffness asymmetry temporarily, the environmental factors will interfere the manual calibration. Combined with virtual rotation, the processing circuits obtain the resonant frequencies of RIG operation modes and a controller is used to reduce the frequency difference. Meanwhile, an innovative method is proposed for RIG angle error analysis, avoiding the drawbacks of the traditional analysis methods. An FPGA based platform using a MEMS disk resonator is tested and the angle error is reduced to 1 degree compared with the manual calibration result 6.1 degrees.
- 23 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (12) , 13384-13393
Design of Force-to-Rebalanced System With Adaptive Fuzzy-PID Controller for N = 3 MEMS Disk Gyroscope
In this paper, an adaptive fuzzy-PID controller is proposed to make the closed-loop drive system of a MEMS disk gyroscope with a high Q respond faster without overshoot and achieve high stability accuracy. The principle of the MEMS disk gyroscope operating in force-to-rebalanced (FTR) mode is studied. An adaptive fuzzy-PID controller is designed and implemented. The fuzzy controller adjusts the parameters of the PID controller online according to the input error and error change rate. The response time of closed-loop drive of the gyroscope is reduced from 1.09 s to 0.54 s, and the overshoot is reduced from 20% to 0.004%, with no degradation in angle random walk (ARW) and bias instability (BI). The FTR control system is implemented on a field programmable gate array (FPGA) platform. The performance of the n=3 MEMS disk gyroscope with natural frequency of 9,536 Hz and a quality factor of ~20000 using the novel FTR control system revealed an ARW of 0.1667 deg/ √ hr and an in-run BI of 1.177 deg/hr.
- 23 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (12) , 13384-13393
Design of Force-to-Rebalanced System With Adaptive Fuzzy-PID Controller for N = 3 MEMS Disk Gyroscope
In this paper, an adaptive fuzzy-PID controller is proposed to make the closed-loop drive system of a MEMS disk gyroscope with a high Q respond faster without overshoot and achieve high stability accuracy. The principle of the MEMS disk gyroscope operating in force-to-rebalanced (FTR) mode is studied. An adaptive fuzzy-PID controller is designed and implemented. The fuzzy controller adjusts the parameters of the PID controller online according to the input error and error change rate. The response time of closed-loop drive of the gyroscope is reduced from 1.09 s to 0.54 s, and the overshoot is reduced from 20% to 0.004%, with no degradation in angle random walk (ARW) and bias instability (BI). The FTR control system is implemented on a field programmable gate array (FPGA) platform. The performance of the n=3 MEMS disk gyroscope with natural frequency of 9,536 Hz and a quality factor of ~20000 using the novel FTR control system revealed an ARW of 0.1667 deg/ √ hr and an in-run BI of 1.177 deg/hr.
- 22 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (14) , 16124-16133
A System Phase Noise Model for Frequency-Modulated MEMS Gyroscopes
A system phase noise model is proposed in this paper for frequency-modulated (FM) gyroscopes, which gives us a clearly guidance for different noise and how to improve the final performance. The author here introduces a mathematical calculation method to deal with the time domain noise and transforms the time-varying noise into phase modulation paths to analyze the frequency noise effect. Meanwhile, the proposed model reveals the relationships about mechanical vibration noise mechanical additional loop noise and performance indicators. In this way, combing frequency spectrum and Allan variance curves, the weight of each noise can be determined. Here, we get different physical noise sources from actual circuit chip by the proposed phase noise decomposition method and analyze the whole noise contribution. After that, we can clearly understand the performance indicators required to design the circuit. Finally, this work offers a whole theory instructions to quantitate different frequency noise for FM gyroscopes.
- 22 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (14) , 16124-16133
A System Phase Noise Model for Frequency-Modulated MEMS Gyroscopes
A system phase noise model is proposed in this paper for frequency-modulated (FM) gyroscopes, which gives us a clearly guidance for different noise and how to improve the final performance. The author here introduces a mathematical calculation method to deal with the time domain noise and transforms the time-varying noise into phase modulation paths to analyze the frequency noise effect. Meanwhile, the proposed model reveals the relationships about mechanical vibration noise mechanical additional loop noise and performance indicators. In this way, combing frequency spectrum and Allan variance curves, the weight of each noise can be determined. Here, we get different physical noise sources from actual circuit chip by the proposed phase noise decomposition method and analyze the whole noise contribution. After that, we can clearly understand the performance indicators required to design the circuit. Finally, this work offers a whole theory instructions to quantitate different frequency noise for FM gyroscopes.
- 1 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (3) , 3241-3249
Rate-Integration Gyroscope (RIG) With Gain Self Calibration
For the purpose of direct angle measurement with high accuracy, this paper focuses on the gain self-calibration of operating modes of MEMS disk gyroscope, when it works in the rate-integration mode. The difference of C/V conversion gain, quality factor and front-end amplifier’s gain of gyroscope operating modes will lead to the total gain difference, which causes angle error. Although one-time manual calibration can temporarily reduce the influence of gain difference, environmental factors (e.g. temperature) will interfere with the calibration results. In this paper, a novel self-calibration method is proposed, which detects the gain difference of gyroscope operating modes in real time and compensates it without adding additional circuits. This method is verified using a digital signal processing platform, and the angle dependent bias (ADB) error is reduced from 18 degrees to 2 degrees.
- 1 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (3) , 3241-3249
Rate-Integration Gyroscope (RIG) With Gain Self Calibration
For the purpose of direct angle measurement with high accuracy, this paper focuses on the gain self-calibration of operating modes of MEMS disk gyroscope, when it works in the rate-integration mode. The difference of C/V conversion gain, quality factor and front-end amplifier’s gain of gyroscope operating modes will lead to the total gain difference, which causes angle error. Although one-time manual calibration can temporarily reduce the influence of gain difference, environmental factors (e.g. temperature) will interfere with the calibration results. In this paper, a novel self-calibration method is proposed, which detects the gain difference of gyroscope operating modes in real time and compensates it without adding additional circuits. This method is verified using a digital signal processing platform, and the angle dependent bias (ADB) error is reduced from 18 degrees to 2 degrees.
- 1 March 2019
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 444, 85-107
Vibration modeling of disk resonator gyroscope by wave propagation
- 1 March 2019
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 444, 85-107
Vibration modeling of disk resonator gyroscope by wave propagation
- 24 October 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10462, 171
Mathematical analysis for image sampling process of CCD
In the photographic process with Charge Coupled Device (CCD), the image sampling of CCD is important. Due to the previous incorrect mathematical descriptions of the sampling, a correct mathematical equation is given by analyzing the CCD image acquisition process. Comparing the previous and the given one, shortcomings of the previous are pointed out. Then, a detailed spectrum analysis of the image sampling is carried out which illustrates the influence of various parameters of CCD on image acquisition. The mathematical analysis can optimize the choice of the parameters of CCD in practical applications.
- 24 October 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10462, 171
Mathematical analysis for image sampling process of CCD
In the photographic process with Charge Coupled Device (CCD), the image sampling of CCD is important. Due to the previous incorrect mathematical descriptions of the sampling, a correct mathematical equation is given by analyzing the CCD image acquisition process. Comparing the previous and the given one, shortcomings of the previous are pointed out. Then, a detailed spectrum analysis of the image sampling is carried out which illustrates the influence of various parameters of CCD on image acquisition. The mathematical analysis can optimize the choice of the parameters of CCD in practical applications.