Haythem Zouabi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Haythem Zouabi has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Gilles Dessein
Laboratoire Génie de Production, ENIT-INPT, Université de Toulouse, Toulouse, France
2 shared publicationsMadalina Calamaz
Arts et Métiers Institute of Technology, University of Bordeaux, CNRS, Bordeaux INP, INRAE, HESAM Université, I2M Bordeaux, France
2 shared publicationsOlivier Cahuc
Arts et Métiers Institute of Technology, Univeristy of Bordeaux, CNRS, Bordeaux INP, INRAE, I2M Bordeaux, France
2 shared publicationsVincent Wagner
Laboratoire Génie de Production, ENIT-INPT, Université de Toulouse, Toulouse, France
2 shared publications- Gilles Dessein
ENIT
1 shared publication - Madalina Calamaz
Univ. Bordeaux, CNRS, Talence, FRANCE
1 shared publication
Latest Publications
- 14 January 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 131 (2) , 531-549
Kinematic fields measurement during Ti-6Al-4V chip formation using new high-speed imaging system
- 14 January 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 131 (2) , 531-549
Kinematic fields measurement during Ti-6Al-4V chip formation using new high-speed imaging system
- Open Access
- 5 April 2022
- Published by Springer Nature in Research Square
Kinematic fields measurement during Ti-6Al-4V chip formation using new high-speed imaging system
In-situ visualization of the material flow during orthogonal cutting is achieved using new high-speed optical system. Difficulties arise from the submillimetric size of the cutting zone. Therefore, a dedicated optical system was designed allowing for local scale analysis of chip formation. The Digital Image Correlation (DIC) technique is applied on recorded images from the cutting zone to measure the kinematic fields. Then, the effect of the cutting conditions on chip formation is presented with local scale analysis.
- 5 April 2022
- Published by Springer Nature in Research Square
Open AccessKinematic fields measurement during Ti-6Al-4V chip formation using new high-speed imaging system
In-situ visualization of the material flow during orthogonal cutting is achieved using new high-speed optical system. Difficulties arise from the submillimetric size of the cutting zone. Therefore, a dedicated optical system was designed allowing for local scale analysis of chip formation. The Digital Image Correlation (DIC) technique is applied on recorded images from the cutting zone to measure the kinematic fields. Then, the effect of the cutting conditions on chip formation is presented with local scale analysis.
- Open Access
- 9 January 2021
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 5 (1) , 7
Kinematic Fields Measurement during Orthogonal Cutting Using Digital Images Correlation: A Review
Understanding the mechanism of chip formation during orthogonal cutting requires a local measurement of the displacement and strain fields in the cutting zone. These measurements can then be used in order to enhance/validate numerical simulation of metal cutting or calibrate material behavior laws for a better prediction of the thermomechanical loads inside the cutting zone. Particle tracking to identify the strain localization that is exhibited in the Adiabatic Shear Band (ASB) is a challenging task. These local measurements can be determined by images post-processing while using the Digital Image Correlation (DIC) technique or analytical models using streamline models or by micro grid analysis. Recently, the use of the DIC technique is widely increased. Texture quality has been shown to be an important factor. Various techniques of surface preparation are then discussed and classified in terms of the created pattern size. Tools for texture analysis are presented. The technique suitability for the kinematic fields measurement while using the DIC technique during machining is discussed. Various optical systems of the literature employed in the context of kinematic fields measurement during machining are discussed in this paper. The recent advances on the design of optical systems are given. Finally, the results of kinematic fields measurement during machining metallic alloys are analyzed.
- 9 January 2021
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 5 (1) , 7
Open AccessKinematic Fields Measurement during Orthogonal Cutting Using Digital Images Correlation: A Review
Understanding the mechanism of chip formation during orthogonal cutting requires a local measurement of the displacement and strain fields in the cutting zone. These measurements can then be used in order to enhance/validate numerical simulation of metal cutting or calibrate material behavior laws for a better prediction of the thermomechanical loads inside the cutting zone. Particle tracking to identify the strain localization that is exhibited in the Adiabatic Shear Band (ASB) is a challenging task. These local measurements can be determined by images post-processing while using the Digital Image Correlation (DIC) technique or analytical models using streamline models or by micro grid analysis. Recently, the use of the DIC technique is widely increased. Texture quality has been shown to be an important factor. Various techniques of surface preparation are then discussed and classified in terms of the created pattern size. Tools for texture analysis are presented. The technique suitability for the kinematic fields measurement while using the DIC technique during machining is discussed. Various optical systems of the literature employed in the context of kinematic fields measurement during machining are discussed in this paper. The recent advances on the design of optical systems are given. Finally, the results of kinematic fields measurement during machining metallic alloys are analyzed.