Ehsan Rahiminejad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ehsan Rahiminejad has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Adel Parvizi-Fard
Medical Biology Research Center, Kermanshah University of Medical Sciences, Kermanshah, Iran
3 shared publications- Mahmood Amiri
University of Antwerp
3 shared publications Hossein Yaghoobzadeh Shadmehri
School of Electrical and Computer Engineering, College of Engineering, University of Tehran, Tehran, Iran
2 shared publications- Nitish Vyomesh Thakor
Department of Biomedical Engineering, Johns Hopkins University, Baltimore, MD, USA
2 shared publications Reza Lotfi
Department of Electrical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
2 shared publicationsAfsaneh Zeinalzadeh
Department of Physical Therapy, School of Paramedical and Rehabilitation Sciences, Mashhad University of Medical Sciences, Mashhad, Iran
1 shared publication
Latest Publications
- 3 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (13) , 20304-20316
Design of a Low-Cost Real-Time Angle Sensor Module for Dynamic Body-Weight Support Systems Using Inertial Measurement Unit and Fusion Algorithms
Dynamic Body Weight-Support (DBWS) systems are used for patients with mobility impairments. These systems provide three key functions—dynamic body-weight support, fall prevention, and synchronized propulsion—all of which were designed and implemented in this study. One of the most important parameters in a DBWS system is the angle between the patient and the device, which is measured by an angle-estimation module. The problem addressed in this research is the design and construction of a low-cost angle measurement module that is minimally sensitive to vibration, maintains high precision, and has a fast response time. This module is suitable for rehabilitation applications (for example DBWS system) that require high precision and are subject to significant vibration. In this paper, by using an inertial measurement unit (IMU) sensor and a switching logic between different filters based on data fusion, low sensitivity to vibration (vibrations caused by mechanical oscillations) and high response speed are achieved. Outputs of Madgwick and Kalman filters (MF and KF) are fused to obtain the angle from the IMU. The MF is employed to detect rapid movements, and two KFs with high and low measurement noise values (HMNV-KF and LMNV-KF) are used to measure the angle. When rapid angular changes occur, the output angle is obtained from the LMNV-KF; otherwise, the HMNV-KF is used. Additionally, a low-pass filter is applied to the LMNV-KF output after fast angular changes have ended but before the HMNV-KF reaching its steady value. The results obtained from the DBWS system show that the proposed algorithm outperforms all other filters in terms of response speed and vibration sensitivity, making it highly suitable for the intended application. The rise time is 171.33 ms, and the maximum error is 0.54°, both of which are lower than those of all other tested filters.
- 3 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (13) , 20304-20316
Design of a Low-Cost Real-Time Angle Sensor Module for Dynamic Body-Weight Support Systems Using Inertial Measurement Unit and Fusion Algorithms
Dynamic Body Weight-Support (DBWS) systems are used for patients with mobility impairments. These systems provide three key functions—dynamic body-weight support, fall prevention, and synchronized propulsion—all of which were designed and implemented in this study. One of the most important parameters in a DBWS system is the angle between the patient and the device, which is measured by an angle-estimation module. The problem addressed in this research is the design and construction of a low-cost angle measurement module that is minimally sensitive to vibration, maintains high precision, and has a fast response time. This module is suitable for rehabilitation applications (for example DBWS system) that require high precision and are subject to significant vibration. In this paper, by using an inertial measurement unit (IMU) sensor and a switching logic between different filters based on data fusion, low sensitivity to vibration (vibrations caused by mechanical oscillations) and high response speed are achieved. Outputs of Madgwick and Kalman filters (MF and KF) are fused to obtain the angle from the IMU. The MF is employed to detect rapid movements, and two KFs with high and low measurement noise values (HMNV-KF and LMNV-KF) are used to measure the angle. When rapid angular changes occur, the output angle is obtained from the LMNV-KF; otherwise, the HMNV-KF is used. Additionally, a low-pass filter is applied to the LMNV-KF output after fast angular changes have ended but before the HMNV-KF reaching its steady value. The results obtained from the DBWS system show that the proposed algorithm outperforms all other filters in terms of response speed and vibration sensitivity, making it highly suitable for the intended application. The rise time is 171.33 ms, and the maximum error is 0.54°, both of which are lower than those of all other tested filters.
- 4 May 2026
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 45 (12) , 9548-9558
A Power-Efficient Analog Circuit for Winner-Take-All and Loser-Take-All Implementation for Edge Detection Applications
- 4 May 2026
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 45 (12) , 9548-9558
A Power-Efficient Analog Circuit for Winner-Take-All and Loser-Take-All Implementation for Edge Detection Applications
- Open Access
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 62 (1)
Power‐ and Area‐Efficient Concurrent Time‐Domain WTA–LTA Circuits
The proposed winner‐take‐all‐loser‐take‐all (WTA–LTA) circuit identifies both the winner and the loser simultaneously using a shared delay line and is suitable for applications where both the winner and the loser are important. Due to the shared delay line between the WTA and LTA cells, power consumption and occupied area are significantly reduced. The power consumption per cell at a frequency of 2 MHz is 5°nW and the occupied area per cell is 41.43°µm 2 . Moreover, the precision of the circuit for three cells is 99.4% for WTA and 99.2% for LTA. The proposed time‐domain WTA‐LTA circuit has been post‐layout simulated in 65‐nm technology with a supply voltage of 0.5 V.
- 1 January 2026
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 62 (1)
Open AccessPower‐ and Area‐Efficient Concurrent Time‐Domain WTA–LTA Circuits
The proposed winner‐take‐all‐loser‐take‐all (WTA–LTA) circuit identifies both the winner and the loser simultaneously using a shared delay line and is suitable for applications where both the winner and the loser are important. Due to the shared delay line between the WTA and LTA cells, power consumption and occupied area are significantly reduced. The power consumption per cell at a frequency of 2 MHz is 5°nW and the occupied area per cell is 41.43°µm 2 . Moreover, the precision of the circuit for three cells is 99.4% for WTA and 99.2% for LTA. The proposed time‐domain WTA‐LTA circuit has been post‐layout simulated in 65‐nm technology with a supply voltage of 0.5 V.
- Open Access
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 61 (1)
A Low Power, High Input Dynamic Range and High Precision Current‐Mode Loser‐Take‐All Circuit
In this paper, a current‐mode loser‐take‐all (LTA) circuit is proposed. The proposed circuit has a high input dynamic range and offers very high precision. The circuit maintains high precision not only at low currents close to zero but also at currents in the range of several hundred microamperes. Additionally, the power consumption per cell in the proposed circuit is very low. The circuit is designed using 180 nm technology, operating at a supply voltage of 1.8 V, with a power consumption of 18 µW per cell in a 3‐input structure. In the proposed circuit, the maximum error occurs at an input range of 200 µA and an input frequency of 2 MHz, which is 1.3%.
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 61 (1)
Open AccessA Low Power, High Input Dynamic Range and High Precision Current‐Mode Loser‐Take‐All Circuit
In this paper, a current‐mode loser‐take‐all (LTA) circuit is proposed. The proposed circuit has a high input dynamic range and offers very high precision. The circuit maintains high precision not only at low currents close to zero but also at currents in the range of several hundred microamperes. Additionally, the power consumption per cell in the proposed circuit is very low. The circuit is designed using 180 nm technology, operating at a supply voltage of 1.8 V, with a power consumption of 18 µW per cell in a 3‐input structure. In the proposed circuit, the maximum error occurs at an input range of 200 µA and an input frequency of 2 MHz, which is 1.3%.
- 18 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (5) , 6824-6833
High Accuracy Approach for Crosstalk Effects Compensation on 2-D Resistive Sensor Array Readouts
Resistive sensor arrays have been increasingly utilized in physical variables measuring. Row-column method is a conventional way for resistive sensors connections. However, the non-idealities of the operational amplifiers, switches and wires reduce the accuracy of the circuit. In this paper, the effect of non-idealities on crosstalk error is analyzed and a new method has been proposed to reduce all nonideality effects simultaneously. The proposed circuit reduces the measuring error by using only two additional buffers. The results of theoretical analysis, simulation and measurement confirm that the proposed method can improve the accuracy. Simulation results of 8×8 array for a 100Ω non-scanned resistance show that the worst-case measuring error is decreased to 0.025%. For a 32Ω resistance of row selection switches and a 32Ω resistance of columns wires, the error is reduced to 0.000027% and 0.00049%, respectively. Also, the simulation results for a 32×32 array shows the maximum error of 0.0005% in the array. Furthermore, an 8×8 resistive array has been designed and implemented which the measurement results confirm that for a 30.9Ω resistance of row selection switches and a 30.9Ω resistance of columns wires, the error is reduced to 0.033% and 0.308%, respectively.
- 18 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (5) , 6824-6833
High Accuracy Approach for Crosstalk Effects Compensation on 2-D Resistive Sensor Array Readouts
Resistive sensor arrays have been increasingly utilized in physical variables measuring. Row-column method is a conventional way for resistive sensors connections. However, the non-idealities of the operational amplifiers, switches and wires reduce the accuracy of the circuit. In this paper, the effect of non-idealities on crosstalk error is analyzed and a new method has been proposed to reduce all nonideality effects simultaneously. The proposed circuit reduces the measuring error by using only two additional buffers. The results of theoretical analysis, simulation and measurement confirm that the proposed method can improve the accuracy. Simulation results of 8×8 array for a 100Ω non-scanned resistance show that the worst-case measuring error is decreased to 0.025%. For a 32Ω resistance of row selection switches and a 32Ω resistance of columns wires, the error is reduced to 0.000027% and 0.00049%, respectively. Also, the simulation results for a 32×32 array shows the maximum error of 0.0005% in the array. Furthermore, an 8×8 resistive array has been designed and implemented which the measurement results confirm that for a 30.9Ω resistance of row selection switches and a 30.9Ω resistance of columns wires, the error is reduced to 0.033% and 0.308%, respectively.
- Open Access
Winner-Take-All and Loser-Take-All Circuits: Architectures, Applications and Analytical Comparison
Different winner-take-all (WTA) and loser-take-all (LTA) circuits are studied, and their operations are analyzed in this review. The exclusive operation of the current conveyor, binary tree, and time-domain WTA/LTA architectures, as the most important architectures reported in the literature, are compared from the perspectives of power consumption, speed, and precision.
Open AccessWinner-Take-All and Loser-Take-All Circuits: Architectures, Applications and Analytical Comparison
Different winner-take-all (WTA) and loser-take-all (LTA) circuits are studied, and their operations are analyzed in this review. The exclusive operation of the current conveyor, binary tree, and time-domain WTA/LTA architectures, as the most important architectures reported in the literature, are compared from the perspectives of power consumption, speed, and precision.
- 30 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (1) , 64-73
A Novel Nociceptor Functional Circuit for Tactile Applications
In this research, the main functional characteristics of nociceptors are considered for designing a novel neuromorphic circuit in TSMC 180 nm CMOS technology with a 1.8 V supply voltage and 780 $\mu$ W power consumption. Indeed, the current study is the first analog circuit realization of the functional model of nociceptors. The proposed circuit includes three spiking neurons. The first and second neurons determine the pressure level and the active area of the stimulus, respectively. The pressure to active area ratio is sensed by the third neuron and helps for better discrimination of the input stimuli. To evaluate the performance of the proposed nociceptor circuit, we perform numerical simulations and robotic experiments. In this way, the 3D-printed objects with different sharpness are touched by a custom-made tactile sensor and the spiking responses from the nociceptor neuromorphic circuit are then collected. Next, machine learning algorithms are applied offline to classify objects based on the rate and time of the spike responses. The results show that by analyzing the spike patterns obtained from the bio-inspired circuit, it is possible to recognize stimuli after the emission of a few spikes. The proposed approach is the proof of concept that circuit implementation of the functional model of the nociceptors expands the range of object recognition and hence facilitates the fabrication of novel tactile sensory systems for bio-robotic and prosthetic applications.
- 30 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (1) , 64-73
A Novel Nociceptor Functional Circuit for Tactile Applications
In this research, the main functional characteristics of nociceptors are considered for designing a novel neuromorphic circuit in TSMC 180 nm CMOS technology with a 1.8 V supply voltage and 780 $\mu$ W power consumption. Indeed, the current study is the first analog circuit realization of the functional model of nociceptors. The proposed circuit includes three spiking neurons. The first and second neurons determine the pressure level and the active area of the stimulus, respectively. The pressure to active area ratio is sensed by the third neuron and helps for better discrimination of the input stimuli. To evaluate the performance of the proposed nociceptor circuit, we perform numerical simulations and robotic experiments. In this way, the 3D-printed objects with different sharpness are touched by a custom-made tactile sensor and the spiking responses from the nociceptor neuromorphic circuit are then collected. Next, machine learning algorithms are applied offline to classify objects based on the rate and time of the spike responses. The results show that by analyzing the spike patterns obtained from the bio-inspired circuit, it is possible to recognize stimuli after the emission of a few spikes. The proposed approach is the proof of concept that circuit implementation of the functional model of the nociceptors expands the range of object recognition and hence facilitates the fabrication of novel tactile sensory systems for bio-robotic and prosthetic applications.
- 21 June 2022
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 112 (3) , 467-473
A 1-V 5-bit 0.5 GS/s time-based flash ADC in 0.18 µm CMOS technology
- 21 June 2022
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 112 (3) , 467-473
A 1-V 5-bit 0.5 GS/s time-based flash ADC in 0.18 µm CMOS technology
- Open Access
- 21 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Neural Systems and Rehabilitation Engineering
- Vol. 29 (15344320) , 2333-2344
A Biomimetic Circuit for Electronic Skin With Application in Hand Prosthesis
One major challenge in upper limb prostheses is providing sensory feedback to amputees. Reproducing the spiking patterns of human primary tactile afferents can be considered as the first step for this challenging problem. In this study, a novel biomimetic circuit for SA-I and RA-I afferents is proposed to functionally replicate the spiking response of the biological tactile afferents to indentation stimuli. The circuit has been designed, laid out, and simulated in TSMC 180nm CMOS technology with a 1.8V supply voltage. A pair of SA-I and RA-I afferent circuits consume $3.5\mu \text{W}$ of power. The occupied silicon area is $180\mu \text{m}\,\,\times 220\mu \text{m}$ for 32 afferents. To provide the inputs for circuit testing, a patch of skin with a grid of mechanoreceptors is simulated and tested by an edge stimulus presented at different orientations. Experimental data are collected using indentation of 3D-printed edges at different orientations on a tactile sensor mounted on a robotic arm. Inspired by innervation patterns observed in biology, the artificial afferents are connected to several neighboring mechanoreceptors with different weights to form complex receptive fields which cover the entire mechanoreceptor grid. Machine learning algorithms are applied offline to classify the edge orientations based on the pattern of neural responses. Our results show that the complex receptive fields arising from the innervation pattern led to smaller circuit area and lower power consumption, while facilitating data encoding from high-resolution sensors. The proposed biomimetic circuit and tactile encoding example demonstrate potential applications in modern tactile sensing modules for developing novel bio-robotic and prosthetic technologies.
- 21 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Neural Systems and Rehabilitation Engineering
- Vol. 29 (15344320) , 2333-2344
Open AccessA Biomimetic Circuit for Electronic Skin With Application in Hand Prosthesis
One major challenge in upper limb prostheses is providing sensory feedback to amputees. Reproducing the spiking patterns of human primary tactile afferents can be considered as the first step for this challenging problem. In this study, a novel biomimetic circuit for SA-I and RA-I afferents is proposed to functionally replicate the spiking response of the biological tactile afferents to indentation stimuli. The circuit has been designed, laid out, and simulated in TSMC 180nm CMOS technology with a 1.8V supply voltage. A pair of SA-I and RA-I afferent circuits consume $3.5\mu \text{W}$ of power. The occupied silicon area is $180\mu \text{m}\,\,\times 220\mu \text{m}$ for 32 afferents. To provide the inputs for circuit testing, a patch of skin with a grid of mechanoreceptors is simulated and tested by an edge stimulus presented at different orientations. Experimental data are collected using indentation of 3D-printed edges at different orientations on a tactile sensor mounted on a robotic arm. Inspired by innervation patterns observed in biology, the artificial afferents are connected to several neighboring mechanoreceptors with different weights to form complex receptive fields which cover the entire mechanoreceptor grid. Machine learning algorithms are applied offline to classify the edge orientations based on the pattern of neural responses. Our results show that the complex receptive fields arising from the innervation pattern led to smaller circuit area and lower power consumption, while facilitating data encoding from high-resolution sensors. The proposed biomimetic circuit and tactile encoding example demonstrate potential applications in modern tactile sensing modules for developing novel bio-robotic and prosthetic technologies.
- 8 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Neural Networks and Learning Systems
- Vol. 33 (5) , 2246-2258
A Neuromorphic CMOS Circuit With Self-Repairing Capability
Neurophysiological observations confirm that the brain not only is able to detect the impaired synapses (in brain damage) but also it is relatively capable of repairing faulty synapses. It has been shown that retrograde signaling by astrocytes leads to the modulation of synaptic transmission and thus bidirectional collaboration of astrocyte with nearby neurons is an important aspect of self-repairing mechanism. Specifically, the retrograde signaling via astrocyte can increase the transmission probability of the healthy synapses linked to the neuron. Motivated by these findings, in the present research, a CMOS neuromorphic circuit with self-repairing capabilities is proposed based on astrocyte signaling. In this way, the computational model of self-repairing process is hired as a basis for designing a novel analog integrated circuit in the 180-nm CMOS technology. It is illustrated that the proposed analog circuit is able to successfully recompense the damaged synapses by appropriately modifying the voltage signals of the remaining healthy synapses in the wide range of frequency. The proposed circuit occupies 7500- $\mu \text{m}^{2}$ silicon area and its power consumption is about $65.4~\mu \text{W}$ . This neuromorphic fault-tolerant circuit can be considered as a key candidate for future silicon neuronal systems and implementation of neurorobotic and neuro-inspired circuits.
- 8 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Neural Networks and Learning Systems
- Vol. 33 (5) , 2246-2258
A Neuromorphic CMOS Circuit With Self-Repairing Capability
Neurophysiological observations confirm that the brain not only is able to detect the impaired synapses (in brain damage) but also it is relatively capable of repairing faulty synapses. It has been shown that retrograde signaling by astrocytes leads to the modulation of synaptic transmission and thus bidirectional collaboration of astrocyte with nearby neurons is an important aspect of self-repairing mechanism. Specifically, the retrograde signaling via astrocyte can increase the transmission probability of the healthy synapses linked to the neuron. Motivated by these findings, in the present research, a CMOS neuromorphic circuit with self-repairing capabilities is proposed based on astrocyte signaling. In this way, the computational model of self-repairing process is hired as a basis for designing a novel analog integrated circuit in the 180-nm CMOS technology. It is illustrated that the proposed analog circuit is able to successfully recompense the damaged synapses by appropriately modifying the voltage signals of the remaining healthy synapses in the wide range of frequency. The proposed circuit occupies 7500- $\mu \text{m}^{2}$ silicon area and its power consumption is about $65.4~\mu \text{W}$ . This neuromorphic fault-tolerant circuit can be considered as a key candidate for future silicon neuronal systems and implementation of neurorobotic and neuro-inspired circuits.