NMNoor Asniza Murad

Noor Asniza Murad

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Noor Asniza Murad has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Sidelobe Level Suppression in Linear and Planar Phased Arrays Using Grey Wolf Optimization With Local Search Refinements

    by Muhammad Athallah Adriansyah, Aditya Inzani Wahdiyat, Ismi Rosyiana Fitri, Noor Asniza Murad, Catur Apriono

    Phased array antennas play a critical role in satellite communication systems, where minimizing peak sidelobe levels (PSLL) is essential to prevent interference and enhance signal quality. This paper presents a novel hybrid optimization approach, grey wolf optimizer with Nelder-Mead local search (GWO-NM), to suppress PSLL effectively in both linear antenna arrays (LAA) and planar antenna arrays (PAA). The proposed method combines the global search capability of greywolf optimizer (GWO) with the Nelder-Mead local refinement to address the PSLL suppression challenge. The optimization process was applied to both 32-element and 100-element LAA, achieving PSLL reductions to -52.63 dB and -56.39 dB, respectively, and these results are also extended to the corresponding PAA configuration. The results were further validated through full-wave electromagnetic simulations in CST Microwave Studio 2024, considering practical effects such as mutual coupling and material losses. Also, this suppression comes with trade-offs, including a widened first null beamwidth from 18.34° to 19.78° for the 32-element arrays and from 6.47° to 9.71° for the 100-element arrays in both LAA and their corresponding PAA compared the conventional algorithm, along with a marginal decrease of 0.5-1 dB in directivity observed in electromagnetic simulations. The GWO-NM algorithm outperformed other metaheuristic optimization techniques, including PSO, ACO, CSO, ABCO, and conventional GWO, demonstrating superior sidelobe suppression across different array configurations while maintaining an acceptable trade-off with other key radiation parameters.


  • Open Access

    Low Loss Wideband 4×4 Butler Matrix Networks Based on Substrate Integrated Waveguide for 5G Applications

    by Yaqdhan Mahmood Hussein, Mohamad Kamal A. Rahim, Noor Asniza Murad, Hatem Oday Hanoosh

    Current wireless communications urgently need to provide huge data rates, high gain and high directivity radiation pattern beams. Therefore, beamforming networks (BFNs) are introduced to provide these needs. Butler matrix (BM) is a type of beamforming network, which can be realized using fixed network circuits and feeds the antenna array. BM at high frequency suffers from components loss and phase error for massive network, especially when it is implemented using common microstrip structures. Different transmission lines such as waveguide and substrate integrated waveguide (SIW) are studied and introduced to realize Butler matrix. SIW structures are good candidate for the implementation of BM due to its property of low loss transmission line which comprises of properties of microstrip and waveguide technology. However, SIW antennas and structures at millimetre waves have unwanted radiation loss coming from the vias holes. In addition, the vias separation distance is dependent on waveguide size, which leads to a more massive beamforming network at 26 GHz. Hence, this thesis is proposing a more size-friendly and optimal SIW antenna beamforming structure to reduce the vias loss and provides higher bandwidth and gain at 26 GHz. The BM components such as 3-dB coupler, 0-dB crossover, and 45-degree phase shifter are designed by implementing metallic vias determination method. Size and distance of vias are the most important factors in determining the coupling ratio and phase shifts at output ports. Hence, the coupler is designed with different vias width and distance to obtain the correct phase and coupling at output ports. Then, the designed coupler is cascaded to form a 0-dB crossover. The phase shifter is designed with alerting vias distance inside the coupling area of SIW structure. The last component in beamforming is the design of SIW slot antenna based on longitude slot distributions. All the components are integrated to form a 4 × 4 BM with four slot antennas attached to BM networks. Microtrip separation feedline used to for coupler, crossover, BM and BFN. The proposed designs are simulated using CST software and fabricated by PCB LPKF ProtoMat printer. The outcomes of wide bandwidth with more than 1 GHz and high directive gain of more than 10 dB for the beamforming network are achieved. The output power of the BM is between -6 dB to -8 dB at all four ports with phase difference error less than 5°. Four directive beams are achieved at beam scanning of -14°, -41°, 41°, and -14° at port 1 to port 4 respectively. Hence, this 4 × 4 BM with four slot antenna theses have introduced a successful design of an antenna beamforming network based on SIW technology with significant characteristics at 26 GHz.


  • Dual-Directional Polarization Insensitive Metamaterial Absorber based on Modified Circular Ring Structure

    by Osman Ayop, Mohamad Kamal A. Rahim, Noor Asniza Murad, Mohamad Fakrie Mohd Ali

    This paper presents the designs and analysis of dual-directional polarization insensitive metamaterial absorbers based on circular ring structure. The circular ring structure is then extended and modified to achieve new performance. The unit cell of the metamaterial consists of a circular ring copper with and without copper lines printed on dual layer of 0.8 mm thick FR4 substrate with dielectric constant of 4.6 and loss tangent of 0.019. The simulated result shows that the circular ring shape metamaterial absorber achieves very high absorbance up to 98.43%. The measurement result confirms the calculated performance in simulation. The circular ring structure can also be modified to achieve new performance such as frequency reduction and dual band response. The new modified metamaterial absorbers also confirm the polarization-independent behavior. Thin metamaterial absorbers are very important for various application such as stealth technology, radar cross section and mutual coupling reduction.

  • Open Access

    Recent Developments of Butler Matrix From Components Design Evolution to System Integration for 5G Beamforming Applications: A Survey

    by Abdulkadir Bello Shallah, Farid Zubir, Mohamad Kamal A. Rahim, Huda A. Majid, Usman Ullah Sheikh, Noor Asniza Murad, Zubaida Yusoff

    Beamforming networks for multiple beam antennas are believed to be in the vanguard of technological developments in mmWave for 5G wireless applications. The basic idea of beamforming technique is the application of multiple antenna elements radiating the same signal at an identical phase and wavelength, into one strong signal pointed to a specific direction. For low cost and power consumption, radio frequency beamforming networks (RF-BFNs) such as Blass matrices, Butler matrices, and Nolen matrices will play a critical role in achieving the ever-increasing demands in wireless technology. Therefore, this study aims to present a comprehensive survey and developments of RF-BFNs with (particular focus in Butler matrices). From the fundamental perspectives of the beamforming techniques and progress over time, component evolution includes branch-line coupler (BLC), Phase shifter (PS), and Crossovers to complete system Butler matrix (BM) integration. Different design techniques to improve bandwidth, size reduction, multi-band, and other performance characteristics are discussed extensively. Furthermore, the paper also discusses different geometry of Butler matrices in open microstrip transmission lines, substrate integrated waveguide (SIW) and gap waveguide (GWG) technologies highlighting key developments and research challenges from single band to dual-band operations. We expect this paper to provide more profound insights into the designs processes and suggest suitable ways to facilitate further developments of RF-beamforming networks at mmWave and sub-mmWave frequency ranges.


  • Open Access

    Design and characterization substrate integrated waveguide antenna for WBANS application

    by Mustafa Mohammed Jawad Abed, Nik Noordini Nik Abd Malik, Noor Asniza Murad, Mona Riza Mohd Esa, Mohd Riduan Ahmad, Ola Hussein Abed Al Radh, Ali Abdulateef Abdulbari, Yaqdhan Mahmood Hussein, Fahad Taha Al-Dhief

    Millimetre-wave frequencies are defined as one of the front-runner contenders for body-centric wireless communication. In this study, low-profile antenna with the substrate integrated waveguide (SIW) has been proposed that operate in the band of the millimetre-wave frequency that has been centred at 60 GHz. The proposed antenna has been implemented with the use of the FR4 substrate with εr and tangent loss of 4.3 and 0.025, respectively. The substrate height and size are 1.5875 mm and 20 mm x 20 mm, respectively. The performance of the antenna is evaluated in off-body (free space) and on-body (human voxel model), through simulation. The proposed antenna has an ultra-wideband (UWB) and a specific absorption rate the maximal (SAR) for (10 g) is 0.0344815 W/kg and for (1 g) is 0.0184723 W/kg. It achieves 74% and 63% efficiency in the off and on-body scenario, respectively. The small antenna with the exceptional matching of impedance, low SAR, broad bandwidth, and good efficiency, a good voltage standing wave ratio good (VSWR), and good front-to-back ratio (FBR). As a result, its characteristics make it one of the best potential candidates for the simultaneous transmission and reception of data at (mm-wave) band for WBAN applications.


  • Open Access

    A Beam-Split Metasurface Antenna for 5G Applications

    by Tamara Z. Fadhil, Noor Asniza Murad, Mohamad Kamal A. Rahim, M. R. Hamid, Levy Olivia Nur

    This article presents a hybrid metasurface split beam antenna for fifth-generation (5G) mobile applications at 3.5 GHz. Multi-beam antennas with high directivity are required for a 5G mobile network. It can be achieved by having an array antenna. Using an antenna array at low frequency increases the complexity and size of the whole network. Therefore, a metasurface (MS) is proposed to direct surface current and to have high gain and multibeam properties. To achieve that, a square split ring resonator (SSRR) and U-shaped unit cell metasurface is implemented as a superstrate to a single square patch antenna. The manipulation of this hybrid metasurface configuration can create opposite current flow on the unit cell and thus split the beam. The hybrid metasurface superstrate and antenna are fabricated on FR-4 ( $\varepsilon \text{r}\,\,=4.4$ , tan $\delta =0.02$ ). Results show that the antenna resonates well at 3.5 GHz, with a less than −10 dB reflection coefficient. The arrangement of the unit cells on the superstrate metasurface is able to split the current, and thus the radiation pattern beam is split into two beams in the E-plane at ± 45°. This antenna is a good candidate for future 5G Pico cell base stations in urban or suburban areas with high capacity and interferences.


  • Complementary split-ring resonator and strip-gap based metamaterial fractal antenna with miniature size and enhanced bandwidth for 5G applications

    by Arshad Karimbu Vallappil, Mohamad Kamal A. Rahim, Bilal A. Khawaja, Muhammad Naeem Iqbal, Noor Asniza Murad, Mohamed Musthapa Gajibo, Levy O. Nur, Bambang S. Nugroho

    This paper proposes two different types of metamaterial (MTM) antennas for fifth-generation (5G) mid-band frequency operation. The radiating patch of the proposed antenna is based on the combined Minkowski-Sierpinski carpet fractal structure. On the ground plane, two different types of MTM structures: Complementary split-ring resonator (CSRR), and Strip-gap are etched to enhance the overall bandwidth and gain of the antenna. The introduction of these structures on the ground plane also leads to antenna miniaturization. Both the proposed MTM structure based antennas resonate at 3.5GHz. The overall size of the two fabricated prototypes is 28×29.5 mm2 / 28×28.5 mm2, which shows the compactness of the proposed design by 43% / 42% as compared to the conventional microstrip patch antenna (MPA). The measured bandwidth/gain achieved by the proposed combined Minkowski-Sierpinski carpet fractal antenna (CMSFA) having CSRR MTM and strip-gap etched on the ground plane are 370 MHz / 2.42dBi and 440 MHz / 3.75dBi, respectively.


  • Open Access

    High Capacity and Miniaturized Flexible Chipless RFID Tag Using Modified Complementary Split Ring Resonator

    by Mohd Ezwan B Jalil, Mohamad Kamal A Rahim, Himdi Mohamed, Noor Asmawati Binti Samsuri, Noor Asniza Murad, Raimi Dewan, Huda Bin A Majid, Nur Biha Mohamed Nafis, Levy Olivia Nur, Bambang Setia Nugroho

    This paper aims to produce a high data capacity and miniaturized flexible chipless RFID tag based on the frequency signature using the Modified Complementary Split Ring Resonator (MCSRR). The proposed 19 bits chipless RFID tag using the frequency shifting technique consists of five slotted overlaying MCSRR with Different Width (MCSRR with DW) structures and the dimension of 48 mm $\times48$ mm. The structure is designed by using a flexible (Polyethylene Terephthalate ) PET substrate with permittivity of 0.2. The operating frequency is between 0.9 GHz and 2.7 GHz. The advancement of slotted overlaying MCSRR with DW structures has successfully miniaturized the chipless RFID tag structure to about $107~{\mathrm {mm}}^{2}$ / bit, $0.02\lambda _{mid}^{2}/\mathrm {bit}$ and 0.09 GHz/bit by maximizing the number of resonators in a limited space and minimizing the frequency separation between the resonators. The omnidirectional tag antenna is incorporated with the proposed MCSRR structure using the retransmission measurement method. The log-periodic antenna with a gain of 5–7 dBi is used for this measurement to improve the range distance between tag and reader system. Based on the retransmission measurement involving the antenna tag, the 19 bits chipless RFID tag which consists of five MCSRR with DW structures can be detected with a maximum range distance of 30 cm and a power transmitted level of 30 dBm.


  • Low loss waveguide-based Butler matrix with iris coupling control method for millimeterwave applications

    by Muataz W. Almeshehe, Noor Asniza Murad, Mohamad Kamal A. Rahim, Osman Ayop, Farid Zubir, Mohamad Zoinol A. Abd. Aziz, Mohamed N. Osman, H. A. Majid

    This paper proposes a low loss 4 × 4 Butler matrix based on rectangular waveguide cavity resonators technology for millimeterwave beamforming network using iris coupling method. This method has the advantage of controlling the electrical fields and the coupling factor inside a complex medium such as waveguide cavity resonators. The coupling factor of 6 dB for 4 × 4 Butler matrix is achieved by tuning the iris coupling k-value between the waveguide cavity resonators. Thus, avoiding a higher phase difference losses and component losses at upper millimeterwave bands. To validate the proposed method, CST software simulations are performed under several iris coupling k-values to achieve a 6 dB coupling factor. Then, the proposed 4 × 4 Butler matrix is 3D metal printed using selective laser melting (SLM) technique. The measured reflection and isolation coefficients are observed below −10 dB, with coupling coefficients ranging between −6 and −7 dB. The phase differences of −42.02°, 42.02°, −130.95°, and 133.3° are achieved at the outputs. It confirmed that using this proposed method has the superiority over the conventional microstrip and waveguide coupling methods by a 1 dB coupling factor loss and a 3° phase difference error.


  • Open Access

    Butler Matrix Based Beamforming Networks for Phased Array Antenna Systems: A Comprehensive Review and Future Directions for 5G Applications

    by Arshad Karimbu Vallappil, Mohamad Kamal A. Rahim, Bilal A. Khawaja, Noor Asniza Murad, Mohammed Gajibo Mustapha

    Due to the rapid development of wireless communication technologies, the number of wireless users are radically increasing. Currently, ~23 billion wireless devices are connected to the internet, and these numbers are expected to increase manifolds in the years to come. The technology growth of the fifth-generation (5G) wireless systems will be needed to meet this high demand of the network. 5G wireless systems offer data-rates of up to 10Gbps, 1-ms latency, and reduced power consumption. It is a known fact that 5G wireless systems will be exploiting beyond the presently used 3 GHz microwave and millimetre-wave (mm-wave) frequency bands. This is the primary driver in the development of the 5G wireless system. Multi-beam Phased array antenna (PAA) systems are typically used in the deployment of 5G systems for high-gain and directionality. In current 5G and future Beyond 5G (B5G) antenna array systems, beamforming networks (BFNs) such as the Butler Matrix (BM) will play a key role in achieving multi-beam characteristics. So, this paper presents an extensive review of the BM based BFNs, and discusses which type of BM will be suitable for the phased array antenna (PAA) systems in the upcoming 5G and next-generation of B5G wireless systems. Moreover, this paper also summarizes the different types of BM designs based on the number of layers. The BMs are classified into the bi-layer, tri-layer, and four-layer structures. It includes different techniques that have been used to solve the problem of crossing, narrow bandwidth, and size reduction of the BM. From the previous studies, it is found that most of the past research work was performed using the bi-layer BM system, whereas the difficult geometries like tri- and four-layer BM are avoided due to their complex fabrication process. It is also found in this paper that the metamaterial (MTM) based bi-layer BM achieves low insertion-loss and phase-error, excellent bandwidth and compact size, and good S-parameter performance, which makes them an ideal BFN candidate for the upcoming 5G and next-generation B5G systems.