Adarsh Tripathi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Adarsh Tripathi has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Anindya Pain
CBRI-Roorkee, Roorkee, India
5 shared publications - Ashok Kumar Singh
CSIR-Central Institute of Mining and Fuel Research, Regional Research Centre, Roorkee, India
4 shared publications - Mohammad Mohsin Khan
Department of Civil Engineering, Indian Institute of Technology, Roorkee, India
4 shared publications - Nachiketa Rai
Department of Earth Sciences, Indian Institute of Technology, Roorkee, India
4 shared publications - Mohd Ashraf Iqbal
Indian Institute of Technology Roorkee
3 shared publications - Anindya Pain
CSIR-Central Building Research Institute
2 shared publications
Latest Publications
- Open Access
- 15 May 2025
- Published by Copernicus GmbH
Dynamic Strength of rock under High strain rates
In rocks, brittle deformation depends on loading rating. With increasing rates, usually greater than ~102 s-1 rock strength increases significantly that results intense fragmentation. Dynamic conditions necessary for rate dependent brittle failure can occur during impact events, seismic ruptures and landslides. Among the geoscientist and rock engineers, Split Hopkinson Pressure Bar (SHPB) is often used for the study of dynamic behavior of rocks under high strain rate condition. Present study focuses on strength behavior of sandstone over the range of strain rate (3.6×10-5 - 2.4×102 s-1) using compression testing machine and Split Hopkinson Pressure Bar (SHPB). The failure mode is also captured by high speed camera. The result demonstrates that dynamic compressive strength increases with increasing strain rate and follows Kimberley’s universal theoretical scaling relationship. Dynamic increase factor (DIF) also shows strong dependency on strain rate. The degree of fragmentation is also compared with existing theoretical fragmentation models. The average fragments size shows strong strain rate dependency over the entire testing range. With the increasing strain rate more pulverized state were observed after the failed specimens. Moreover, the mean fragment sizes are well described by power law function of strain rate.
- 15 May 2025
- Published by Copernicus GmbH
Open AccessDynamic Strength of rock under High strain rates
In rocks, brittle deformation depends on loading rating. With increasing rates, usually greater than ~102 s-1 rock strength increases significantly that results intense fragmentation. Dynamic conditions necessary for rate dependent brittle failure can occur during impact events, seismic ruptures and landslides. Among the geoscientist and rock engineers, Split Hopkinson Pressure Bar (SHPB) is often used for the study of dynamic behavior of rocks under high strain rate condition. Present study focuses on strength behavior of sandstone over the range of strain rate (3.6×10-5 - 2.4×102 s-1) using compression testing machine and Split Hopkinson Pressure Bar (SHPB). The failure mode is also captured by high speed camera. The result demonstrates that dynamic compressive strength increases with increasing strain rate and follows Kimberley’s universal theoretical scaling relationship. Dynamic increase factor (DIF) also shows strong dependency on strain rate. The degree of fragmentation is also compared with existing theoretical fragmentation models. The average fragments size shows strong strain rate dependency over the entire testing range. With the increasing strain rate more pulverized state were observed after the failed specimens. Moreover, the mean fragment sizes are well described by power law function of strain rate.
- Open Access
- 20 January 2025
- Published by Copernicus GmbH
Dynamic Compressive Strength of Thermally Treated Barakar Sandstone
Assessing the thermal influence on the dynamic mechanical properties of Barakar sandstone is crucial, notably in the examination of subsidence phenomena induced by underground coalmine fires in tandem with blast-induced loading. The Jharia region had been affected by underground coalmine fires, resulting in surface fracturing on both small and large scales. So, the objective of the study is to examine the impact of high temperature on the dynamic compressive strength of colliery sandstone subsurface samples, and its correlation with the mineralogical properties. To accomplish this objective, samples were subjected to a 24-hour heat treatment in a furnace at a controlled heating rate of 5°C/min, followed by natural cooling within the furnace. The samples were divided into five groups, each undergoing different thermal treatments at temperatures of 25°C, 200°C, 400°C, 600°C, and 800°C. The dynamic compressive strength was obtained by performing the dynamic compression tests on Split Hopkinson Pressure Bar setup. The results clearly indicate that up to a critical temperature i.e. 400°C, both quasi-static and dynamic compressive strength showing the minor strengthening effect. However, beyond this critical temperature, there is a significant decrease in strength, particularly up to 800°C. Additionally, for each temperature, the dynamic strength also exhibits an increasing trend with increase in strain rate. The study investigated the applicability of the Kimberley Theoretical Universal Scaling Law in predicting the dynamic compressive strength of thermally treated sandstone across different strain rates. Furthermore, it pinpointed the characteristic strain rate at which the dynamic compressive strength of thermally treated sandstone doubled in comparison to its quasi-static compressive strength.
- 20 January 2025
- Published by Copernicus GmbH
Open AccessDynamic Compressive Strength of Thermally Treated Barakar Sandstone
Assessing the thermal influence on the dynamic mechanical properties of Barakar sandstone is crucial, notably in the examination of subsidence phenomena induced by underground coalmine fires in tandem with blast-induced loading. The Jharia region had been affected by underground coalmine fires, resulting in surface fracturing on both small and large scales. So, the objective of the study is to examine the impact of high temperature on the dynamic compressive strength of colliery sandstone subsurface samples, and its correlation with the mineralogical properties. To accomplish this objective, samples were subjected to a 24-hour heat treatment in a furnace at a controlled heating rate of 5°C/min, followed by natural cooling within the furnace. The samples were divided into five groups, each undergoing different thermal treatments at temperatures of 25°C, 200°C, 400°C, 600°C, and 800°C. The dynamic compressive strength was obtained by performing the dynamic compression tests on Split Hopkinson Pressure Bar setup. The results clearly indicate that up to a critical temperature i.e. 400°C, both quasi-static and dynamic compressive strength showing the minor strengthening effect. However, beyond this critical temperature, there is a significant decrease in strength, particularly up to 800°C. Additionally, for each temperature, the dynamic strength also exhibits an increasing trend with increase in strain rate. The study investigated the applicability of the Kimberley Theoretical Universal Scaling Law in predicting the dynamic compressive strength of thermally treated sandstone across different strain rates. Furthermore, it pinpointed the characteristic strain rate at which the dynamic compressive strength of thermally treated sandstone doubled in comparison to its quasi-static compressive strength.
- 29 March 2024
- Published by Springer Nature in Journal of Earth System Science
- Vol. 133 (2) , 1-28
Control of microstructural and mineralogical characteristics on thermo-elastic behaviour of coal-bearing sandstone under mild to high-temperature regimes: Experimental investigation and development of AI prediction models
- 29 March 2024
- Published by Springer Nature in Journal of Earth System Science
- Vol. 133 (2) , 1-28
Control of microstructural and mineralogical characteristics on thermo-elastic behaviour of coal-bearing sandstone under mild to high-temperature regimes: Experimental investigation and development of AI prediction models
- Open Access
- 4 March 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-15
Experimental study on the quasi-static and dynamic tensile behaviour of thermally treated Barakar sandstone in Jharia coal mine fire region, India
In the present study, the effect of mild to high-temperature regimes on the quasi-static and dynamic tensile behaviours of Barakar sandstone from the Jharia coal mine fire region has been experimentally investigated. The experimental work has been performed on Brazilian disk specimens of Barakar sandstone, which are thermally treated up to 800 °C. The quasi-static and dynamic split tensile strength tests were carried out on a servo-controlled universal testing machine and Split Hopkinson Pressure Bar (SHPB), respectively. Microscopic and mineralogical changes were studied through a petrographic investigation. The experimental results suggest the prevalence of both, static and dynamic loading scenarios after 400 °C. Up to 400 °C, the quasi-static and dynamic tensile strengths increased due to the evaporation of water, which suggests a strengthening effect. However, beyond 400 °C, both strengths decreased significantly as newly formed thermal microcracks became prevalent. The dynamic tensile strength exhibits strain rate sensitivity up to 400 °C, although it shows a marginal decline in this sensitivity beyond this temperature threshold. The Dynamic Increase Factor (DIF) remained constant up to 400 °C and slightly increased after 400 °C. Furthermore, the characteristic strain rate at which the dynamic strength becomes twice the quasi-static strength remains consistent until reaching 400 °C but steadily decreases beyond this temperature. This experimental study represents the first attempt to validate the Kimberley model specifically for thermally treated rocks. Interestingly, the presence of water did not have a significant impact on the failure modes up to 400 °C, as the samples exhibited a dominant tensile failure mode, breaking into two halves with fewer fragments. However, as temperature increased, the failure behaviours became more complex due to the combined influence of thermally induced microcracks and the applied impact load. Cracks initially formed at the centre and subsequently, multiple shear cracks emerged and propagated in the loading direction, resulting in a high degree of fragmentation. This study also demonstrates that shear failure is not solely dependent on the loading rate but can also be influenced by temperature, further affecting the failure mode of the sandstone.
- 4 March 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-15
Open AccessExperimental study on the quasi-static and dynamic tensile behaviour of thermally treated Barakar sandstone in Jharia coal mine fire region, India
In the present study, the effect of mild to high-temperature regimes on the quasi-static and dynamic tensile behaviours of Barakar sandstone from the Jharia coal mine fire region has been experimentally investigated. The experimental work has been performed on Brazilian disk specimens of Barakar sandstone, which are thermally treated up to 800 °C. The quasi-static and dynamic split tensile strength tests were carried out on a servo-controlled universal testing machine and Split Hopkinson Pressure Bar (SHPB), respectively. Microscopic and mineralogical changes were studied through a petrographic investigation. The experimental results suggest the prevalence of both, static and dynamic loading scenarios after 400 °C. Up to 400 °C, the quasi-static and dynamic tensile strengths increased due to the evaporation of water, which suggests a strengthening effect. However, beyond 400 °C, both strengths decreased significantly as newly formed thermal microcracks became prevalent. The dynamic tensile strength exhibits strain rate sensitivity up to 400 °C, although it shows a marginal decline in this sensitivity beyond this temperature threshold. The Dynamic Increase Factor (DIF) remained constant up to 400 °C and slightly increased after 400 °C. Furthermore, the characteristic strain rate at which the dynamic strength becomes twice the quasi-static strength remains consistent until reaching 400 °C but steadily decreases beyond this temperature. This experimental study represents the first attempt to validate the Kimberley model specifically for thermally treated rocks. Interestingly, the presence of water did not have a significant impact on the failure modes up to 400 °C, as the samples exhibited a dominant tensile failure mode, breaking into two halves with fewer fragments. However, as temperature increased, the failure behaviours became more complex due to the combined influence of thermally induced microcracks and the applied impact load. Cracks initially formed at the centre and subsequently, multiple shear cracks emerged and propagated in the loading direction, resulting in a high degree of fragmentation. This study also demonstrates that shear failure is not solely dependent on the loading rate but can also be influenced by temperature, further affecting the failure mode of the sandstone.
- Open Access
- 15 May 2023
- Published by Copernicus GmbH
Dynamic tensile behaviour of Barakar sandstone under high-temperature conditions
Rocks are very much susceptible to deformation in tension, especially under elevated temperatures. Therefore, the study of the dynamic tensile behaviour of rock exposed to high temperature is highly significant to understand the tensile deformation behaviour in dynamic loading conditions which will be proved useful in a variety of engineering problems such as quantifying the blast load impact in fire affected underground/opencast coal mine regions; assessment of ground subsidence due to coalmine fire coupled with blast loading etc. The Jharia coalfield region, known as the coal capital of India, is affected by pervasive underground coalmine fire for decades resulting in small to large-scale surface fracturing. So,the present study focuses on the effect of high temperature on dynamic tensile behaviour and its relation with micro-mineralogical properties of subsurface coal-bearing sandstone samples from a fire-affected mine. To achieve the objective, the prepared samples were kept in the furnace for 24h with a heating rate of 5°C/min and then allowed to cool down naturally within the furnace. Samples were divided into nine groups based on the thermal treatment at 25 °C, 100 °C, 200 °C, 300 °C, 400 °C, 500 °C, 600 °C, 700 °C, and 800 °C. Using the Split-Hopkinson Pressure Bar (SHPB), the indirect dynamic tensile strength was measured for each group. Based on the obtained results, the indirect dynamic tensile strength of heat-treated specimens is characterized into three zones; viz.: Zone 1 (25-400°C), Zone 2 (400-600°C) and Zone 3 (600-800°C). In zone 1, an increase in average indirect dynamic tensile strength is observed with elevated temperature. However, in zone 2, a sharp decreasing trend in indirect dynamic tensile strength was observed with increasing temperature. This zone is characterised by a progressive increase in thermal cracks and porosity which is possibly the prime reason for a sharp transition in thermal properties. An overall reduction in indirect dynamic tensile strength is observed within zone 3, however, the rate of reduction is gentle. The plasticity that occurred due to high temperature was responsible for a slow rate of reduction in indirect dynamic tensile strength.
- 15 May 2023
- Published by Copernicus GmbH
Open AccessDynamic tensile behaviour of Barakar sandstone under high-temperature conditions
Rocks are very much susceptible to deformation in tension, especially under elevated temperatures. Therefore, the study of the dynamic tensile behaviour of rock exposed to high temperature is highly significant to understand the tensile deformation behaviour in dynamic loading conditions which will be proved useful in a variety of engineering problems such as quantifying the blast load impact in fire affected underground/opencast coal mine regions; assessment of ground subsidence due to coalmine fire coupled with blast loading etc. The Jharia coalfield region, known as the coal capital of India, is affected by pervasive underground coalmine fire for decades resulting in small to large-scale surface fracturing. So,the present study focuses on the effect of high temperature on dynamic tensile behaviour and its relation with micro-mineralogical properties of subsurface coal-bearing sandstone samples from a fire-affected mine. To achieve the objective, the prepared samples were kept in the furnace for 24h with a heating rate of 5°C/min and then allowed to cool down naturally within the furnace. Samples were divided into nine groups based on the thermal treatment at 25 °C, 100 °C, 200 °C, 300 °C, 400 °C, 500 °C, 600 °C, 700 °C, and 800 °C. Using the Split-Hopkinson Pressure Bar (SHPB), the indirect dynamic tensile strength was measured for each group. Based on the obtained results, the indirect dynamic tensile strength of heat-treated specimens is characterized into three zones; viz.: Zone 1 (25-400°C), Zone 2 (400-600°C) and Zone 3 (600-800°C). In zone 1, an increase in average indirect dynamic tensile strength is observed with elevated temperature. However, in zone 2, a sharp decreasing trend in indirect dynamic tensile strength was observed with increasing temperature. This zone is characterised by a progressive increase in thermal cracks and porosity which is possibly the prime reason for a sharp transition in thermal properties. An overall reduction in indirect dynamic tensile strength is observed within zone 3, however, the rate of reduction is gentle. The plasticity that occurred due to high temperature was responsible for a slow rate of reduction in indirect dynamic tensile strength.
- Open Access
- 4 March 2021
- Published by Copernicus GmbH
Deformational characteristics of thermally treated sandstone from an underground coalmine fire region, India
The Jharia region of lower Gondwana in India is one of the largest Underground Coalmine Fires (UCF) affected coalfield in the world. The UCF induced small scale as well as large-scale surface fracturing often creates the life-threatening conditions to coal miners and local surroundings. So, there is a need to understand the thermomechanical behaviour of coal measures rocks to predict the land disturbances in thermo-environmental conditions. It will provide an insight into the UCF induced subsidence mechanism and its preventive measures. The Jharia coal field predominantly consists of sandstone (75-80% by volume) and rest is composed of coal, shale and carbonaceous shale. The present study focuses on thermo-mechanical behaviour of Barakar sandstone (BS) under elevated temperatures. The cores of BS sample were prepared according to the ISRM standards. Further, samples were grouped and thermally treated in temperature range of 25°C, 100°C, 150°C, 300°C, 400°C, 500°C, 600 °C, 700°C and 800°C at a heating rate of 5°C/min for 24 hours in furnace. Then, these thermally treated BS samples were subjected to laboratory test for stress-strain characteristics. In the process of deformational characteristics evaluation, effect of mineralogical changes and mode of fracture pattern were also studied at the mentioned elevated temperature. Based on the obtained results, the deformational behaviour of thermally treated BS specimens can be grouped into three zones, viz., zone 1 (25-300°C), zone 2 (300-500°C) and zone 3 (500-800°C). In zone 1, the characteristics of the stress-strain curve is similar to those under air dried sandstone specimen. However, small increment in stiffness were observed upto 300°C. The stress-strain curves in this zone shows dominantly brittle fracturing. The increment in stiffness may be related to evaporation of pore water that increases the cohesion between the mineral grains resulting higher stiffness value. In zone 2, the deformation pattern again shows brittle fracturing with continuous decrement in stiffness. The reduction in stiffness may be related to thermally induced porosity and increased microcrack density. In zone 3, the stress strain curve is observed to be concave upward. It indicates the pseudo-ductile behaviour of the thermally treated BS specimens. The observed results suggest a typical behaviour of deformation pattern under UCF induced rock fracturing which may be useful in predicting the land subsidence in UCF affected areas. Present research outcome may be used to design the support measures to reduce the associated hazards.
- 4 March 2021
- Published by Copernicus GmbH
Open AccessDeformational characteristics of thermally treated sandstone from an underground coalmine fire region, India
The Jharia region of lower Gondwana in India is one of the largest Underground Coalmine Fires (UCF) affected coalfield in the world. The UCF induced small scale as well as large-scale surface fracturing often creates the life-threatening conditions to coal miners and local surroundings. So, there is a need to understand the thermomechanical behaviour of coal measures rocks to predict the land disturbances in thermo-environmental conditions. It will provide an insight into the UCF induced subsidence mechanism and its preventive measures. The Jharia coal field predominantly consists of sandstone (75-80% by volume) and rest is composed of coal, shale and carbonaceous shale. The present study focuses on thermo-mechanical behaviour of Barakar sandstone (BS) under elevated temperatures. The cores of BS sample were prepared according to the ISRM standards. Further, samples were grouped and thermally treated in temperature range of 25°C, 100°C, 150°C, 300°C, 400°C, 500°C, 600 °C, 700°C and 800°C at a heating rate of 5°C/min for 24 hours in furnace. Then, these thermally treated BS samples were subjected to laboratory test for stress-strain characteristics. In the process of deformational characteristics evaluation, effect of mineralogical changes and mode of fracture pattern were also studied at the mentioned elevated temperature. Based on the obtained results, the deformational behaviour of thermally treated BS specimens can be grouped into three zones, viz., zone 1 (25-300°C), zone 2 (300-500°C) and zone 3 (500-800°C). In zone 1, the characteristics of the stress-strain curve is similar to those under air dried sandstone specimen. However, small increment in stiffness were observed upto 300°C. The stress-strain curves in this zone shows dominantly brittle fracturing. The increment in stiffness may be related to evaporation of pore water that increases the cohesion between the mineral grains resulting higher stiffness value. In zone 2, the deformation pattern again shows brittle fracturing with continuous decrement in stiffness. The reduction in stiffness may be related to thermally induced porosity and increased microcrack density. In zone 3, the stress strain curve is observed to be concave upward. It indicates the pseudo-ductile behaviour of the thermally treated BS specimens. The observed results suggest a typical behaviour of deformation pattern under UCF induced rock fracturing which may be useful in predicting the land subsidence in UCF affected areas. Present research outcome may be used to design the support measures to reduce the associated hazards.
- 10 January 2021
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 54 (3) , 1293-1314
Effects of Elevated Temperatures on the Microstructural, Physico-Mechanical and Elastic Properties of Barakar Sandstone: A Study from One of the World’s Largest Underground Coalmine Fire Region, Jharia, India
- 10 January 2021
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 54 (3) , 1293-1314
Effects of Elevated Temperatures on the Microstructural, Physico-Mechanical and Elastic Properties of Barakar Sandstone: A Study from One of the World’s Largest Underground Coalmine Fire Region, Jharia, India