Sichao Wen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sichao Wen has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Yuandan Dong
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
10 shared publications - Yizhen Xu
School of Electronic Engineering, University of Electronic Science and Technology of China, Chengdu, China
6 shared publications Hailong Wang
Sichuan Province Engineering Research Center for Broadband Microwave Circuit with High Density Integration, Chengdu, China
1 shared publication- Shuosheng Ji
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
1 shared publication - Yilong Zhu
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu 611731, China
1 shared publication Yizhen Xu
University of Electronic Science and Technology of China,School of Electronic Science and Engineering,Chengdu,China
1 shared publication
Latest Publications
- 28 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (9) , 8602-8607
Omnidirectional Circularly Polarized Antenna Array With Planar Configuration
A compact omnidirectional circularly polarized (OCP) linear antenna array with a planar configuration is presented in this communication. By using the cavity model, a shorted half mode patch antenna is analyzed, where the TM modes are taken into consideration. The periodical reversal of the structure at the null point of the higher order mode produces an equivalent long magnetic source array (LMSA) at the open aperture based on the duality principle. Meanwhile, rectangular plates are periodically introduced at the junction of two adjacent cells on the upper or lower surfaces, on which lateral current is generated along the same direction that realizes an equivalent long electric source array (LESA). As a result, two naturally parallel arrays, which are the LMSA and the LESA, are obtained and integrated into a compact format. With the equal magnitude and an inherent 90° phase difference, the two array sources could generate an OCP radiation. Furthermore, a matching network is utilized to expand the impedance bandwidth. Ultimately, a planar $1 \times5$ OCP antenna array is fabricated and tested to verify the design. A −10 dB impedance bandwidth of 8.1% (5.35–5.8 GHz) and a peak LHCP gain of 4.6 dBic are achieved. Good OCP radiation patterns are obtained across the operation band.
- 28 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (9) , 8602-8607
Omnidirectional Circularly Polarized Antenna Array With Planar Configuration
A compact omnidirectional circularly polarized (OCP) linear antenna array with a planar configuration is presented in this communication. By using the cavity model, a shorted half mode patch antenna is analyzed, where the TM modes are taken into consideration. The periodical reversal of the structure at the null point of the higher order mode produces an equivalent long magnetic source array (LMSA) at the open aperture based on the duality principle. Meanwhile, rectangular plates are periodically introduced at the junction of two adjacent cells on the upper or lower surfaces, on which lateral current is generated along the same direction that realizes an equivalent long electric source array (LESA). As a result, two naturally parallel arrays, which are the LMSA and the LESA, are obtained and integrated into a compact format. With the equal magnitude and an inherent 90° phase difference, the two array sources could generate an OCP radiation. Furthermore, a matching network is utilized to expand the impedance bandwidth. Ultimately, a planar $1 \times5$ OCP antenna array is fabricated and tested to verify the design. A −10 dB impedance bandwidth of 8.1% (5.35–5.8 GHz) and a peak LHCP gain of 4.6 dBic are achieved. Good OCP radiation patterns are obtained across the operation band.
- 28 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. ume1, 1-3
A D-Band Magneto-Electric Dipole Antenna Array Based on LTCC Technology
A D-band 4×4 magneto-electric (ME) dipole antenna array based on low temperature co-fired ceramic (LTCC) technology is proposed in this work. The feed of the element antenna of this array is composed of two-stage coupling slots, and the antenna part is an ME dipole antenna surrounded by a metal via-hole cavity. The proposed antenna array achieves a peak gain of 19.3 dBi at 159 GHz and an impedance bandwidth of 12.8 % from 149.5 GHz to 170 GHz. The antenna array has the advantages of compact structure, high gain and a large bandwidth, providing it with high potential in future terahertz communication applications.
- 28 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. ume1, 1-3
A D-Band Magneto-Electric Dipole Antenna Array Based on LTCC Technology
A D-band 4×4 magneto-electric (ME) dipole antenna array based on low temperature co-fired ceramic (LTCC) technology is proposed in this work. The feed of the element antenna of this array is composed of two-stage coupling slots, and the antenna part is an ME dipole antenna surrounded by a metal via-hole cavity. The proposed antenna array achieves a peak gain of 19.3 dBi at 159 GHz and an impedance bandwidth of 12.8 % from 149.5 GHz to 170 GHz. The antenna array has the advantages of compact structure, high gain and a large bandwidth, providing it with high potential in future terahertz communication applications.
- 16 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (12) , 2407-2411
Planar Quasi-Isotropic Antenna and Its Implementation of Filtering Response
Two planar quasi-isotropic antennas are presented in this letter, and the filtering response is implemented on the second antenna. First, a printed shorted patch which can be equivalent to a magnetic dipole is utilized with a fan-shaped monopole serving as an electric dipole to achieve quasi-isotropic radiation. A lumped capacitor, a pair of near-field parasitic elements and a slot are introduced to improve the roundness. Ultimately, the gain deviation is reduced to 3.5 dB. Furthermore, a half-mode substrate integrated waveguide is applied to achieve the magnetic dipole for the second antenna. The filtering response is obtained by introducing a uniform impedance resonator. A radiation null is obtained above the operating band, whereas a quasi-isotropic radiation is achieved in band with a gain deviation of 7.3 dB.
- 16 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (12) , 2407-2411
Planar Quasi-Isotropic Antenna and Its Implementation of Filtering Response
Two planar quasi-isotropic antennas are presented in this letter, and the filtering response is implemented on the second antenna. First, a printed shorted patch which can be equivalent to a magnetic dipole is utilized with a fan-shaped monopole serving as an electric dipole to achieve quasi-isotropic radiation. A lumped capacitor, a pair of near-field parasitic elements and a slot are introduced to improve the roundness. Ultimately, the gain deviation is reduced to 3.5 dB. Furthermore, a half-mode substrate integrated waveguide is applied to achieve the magnetic dipole for the second antenna. The filtering response is obtained by introducing a uniform impedance resonator. A radiation null is obtained above the operating band, whereas a quasi-isotropic radiation is achieved in band with a gain deviation of 7.3 dB.
- 16 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (12) , 2397-2401
Vertically Polarized Loop-Fed Slot Antenna With Top-Loading Metasurface for Omnidirectional LTE Base Station Application
A novel wideband vertically polarized (VP) omnidirectional antenna is proposed in this letter. Two crossed bowtie slots are fed by a loop which is arranged above the ground vertically. The loop works in the one wavelength mode together with its image with respect to the ground, and accordingly the quasi-omnidirectional radiation can be achieved. The bowtie slots are introduced to expand the working bandwidth. Afterwards, a top-loading patch is utilized to improve the impedance matching. Furthermore, the complete patch is replaced by the metasurface to suppress the lateral current so that the stable omnidirectional radiation can be maintained in the operating band. A prototype is fabricated and measured. The -10 dB impedance bandwidth covers the LTE band of 1.7-2.7 GHz. The proposed antenna is well tailored for indoor ceiling base station applications.
- 16 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (12) , 2397-2401
Vertically Polarized Loop-Fed Slot Antenna With Top-Loading Metasurface for Omnidirectional LTE Base Station Application
A novel wideband vertically polarized (VP) omnidirectional antenna is proposed in this letter. Two crossed bowtie slots are fed by a loop which is arranged above the ground vertically. The loop works in the one wavelength mode together with its image with respect to the ground, and accordingly the quasi-omnidirectional radiation can be achieved. The bowtie slots are introduced to expand the working bandwidth. Afterwards, a top-loading patch is utilized to improve the impedance matching. Furthermore, the complete patch is replaced by the metasurface to suppress the lateral current so that the stable omnidirectional radiation can be maintained in the operating band. A prototype is fabricated and measured. The -10 dB impedance bandwidth covers the LTE band of 1.7-2.7 GHz. The proposed antenna is well tailored for indoor ceiling base station applications.
- 8 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (12) , 2334-2338
C/X Dual-Band Circularly Polarized Shared-Aperture Antenna
A novel dual-band circularly polarized (CP) shared-aperture antenna is proposed in this letter. The overall structure consists of a substrate-integrated waveguide (SIW) slot antenna working in the X -band, which also serves as the top patch of a C -band microstrip-like antenna. The SIW slot antenna achieves CP radiation by etching a circular slot on the top surface of a dual-mode SIW cavity. The patch antenna realizes CP radiation by loading two pairs of asymmetric shorting vias. With this design method, the proposed antenna can achieve dual-band CP operation and high aperture reuse efficiency. Besides, the feeding pin of the SIW slot antenna inserts through one of the asymmetric shorting vias, that is, the shorting vias serves as both perturbations for the C -band operation and a feeding path for the X -band operation. This new feeding scheme can prevent signal crosstalk between the two bands.
- 8 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (12) , 2334-2338
C/X Dual-Band Circularly Polarized Shared-Aperture Antenna
A novel dual-band circularly polarized (CP) shared-aperture antenna is proposed in this letter. The overall structure consists of a substrate-integrated waveguide (SIW) slot antenna working in the X -band, which also serves as the top patch of a C -band microstrip-like antenna. The SIW slot antenna achieves CP radiation by etching a circular slot on the top surface of a dual-mode SIW cavity. The patch antenna realizes CP radiation by loading two pairs of asymmetric shorting vias. With this design method, the proposed antenna can achieve dual-band CP operation and high aperture reuse efficiency. Besides, the feeding pin of the SIW slot antenna inserts through one of the asymmetric shorting vias, that is, the shorting vias serves as both perturbations for the C -band operation and a feeding path for the X -band operation. This new feeding scheme can prevent signal crosstalk between the two bands.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (9) , 5974-5979
A Low-Profile Dual-Polarized Omnidirectional Antenna for LTE Base Station Applications
A novel low-profile dual-polarized omnidirectional antenna is proposed in this communication, which is designed for 1.7-2.7 GHz LTE band operation. The horizontally polarized (HP) omnidirectional radiation is realized by a circular slot array. Eight stepped-impedance slots are fed by a 1-to-8 T-junction power divider with equal amplitudes and phases. On the other hand, the vertically polarized (VP) omnidirectional radiation is realized by using the characteristics of the TM0n mode of the cylindrical cavity, where eight shorting copper sheet are used to excite TM01 and TM02 modes. A 1-to-4 T-junction power divider is used to feed the VP unit and achieve good impedance matching. The HP antenna is used to replace the top metal disk of the VP antenna unit, and eight slots are etched on the ground of the vertical polarization unit. It substantially solves the problem of matching deterioration when the horizontal polarization antenna is placed close to the ground. Besides, a special feeding method is employed to avoid the feeding intersection, which commonly appears in dual-polarized antennas. The antenna achieves an isolation around 35 dB and it has a low-profile of 0.07λmin, with λmin being the free space wavelength at the lowest operation frequency. The proposed antenna has an omnidirectional beam, which is very suitable for indoor ceiling base station applications.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (9) , 5974-5979
A Low-Profile Dual-Polarized Omnidirectional Antenna for LTE Base Station Applications
A novel low-profile dual-polarized omnidirectional antenna is proposed in this communication, which is designed for 1.7-2.7 GHz LTE band operation. The horizontally polarized (HP) omnidirectional radiation is realized by a circular slot array. Eight stepped-impedance slots are fed by a 1-to-8 T-junction power divider with equal amplitudes and phases. On the other hand, the vertically polarized (VP) omnidirectional radiation is realized by using the characteristics of the TM0n mode of the cylindrical cavity, where eight shorting copper sheet are used to excite TM01 and TM02 modes. A 1-to-4 T-junction power divider is used to feed the VP unit and achieve good impedance matching. The HP antenna is used to replace the top metal disk of the VP antenna unit, and eight slots are etched on the ground of the vertical polarization unit. It substantially solves the problem of matching deterioration when the horizontal polarization antenna is placed close to the ground. Besides, a special feeding method is employed to avoid the feeding intersection, which commonly appears in dual-polarized antennas. The antenna achieves an isolation around 35 dB and it has a low-profile of 0.07λmin, with λmin being the free space wavelength at the lowest operation frequency. The proposed antenna has an omnidirectional beam, which is very suitable for indoor ceiling base station applications.
- 26 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (4) , 488-492
Low-Profile Wideband Omnidirectional Antenna for 4G/5G Indoor Base Station Application Based on Multiple Resonances
A novel low-profile antenna with monopole-like radiation characteristics is proposed for 4G/5G indoor micro ceiling base station applications. The proposed antenna consists of a top loading disk, two polygonal copper sheets which are orthogonally intersected, and a circular printed circuit board which serves as the ground. A prototype is fabricated and measured. The proposed antenna has a very low profile of 0.057 $\lambda_{\text min}$ , where $\lambda_{\text min}$ is the free space wavelength at the lowest frequency of the operating band. A fractional bandwidth of 85.3% ranging from 1.6 GHz to 3.98 GHz with |S11| <- 10 dB is achieved which covers the 4G LTE band and 5G N78 band. The proposed antenna demonstrates consistent monopole-like radiation pattern in the whole working band, which is very suitable and well designed for indoor ceiling base station applications.- 26 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (4) , 488-492
Low-Profile Wideband Omnidirectional Antenna for 4G/5G Indoor Base Station Application Based on Multiple Resonances
A novel low-profile antenna with monopole-like radiation characteristics is proposed for 4G/5G indoor micro ceiling base station applications. The proposed antenna consists of a top loading disk, two polygonal copper sheets which are orthogonally intersected, and a circular printed circuit board which serves as the ground. A prototype is fabricated and measured. The proposed antenna has a very low profile of 0.057 $\lambda_{\text min}$ , where $\lambda_{\text min}$ is the free space wavelength at the lowest frequency of the operating band. A fractional bandwidth of 85.3% ranging from 1.6 GHz to 3.98 GHz with |S11| <- 10 dB is achieved which covers the 4G LTE band and 5G N78 band. The proposed antenna demonstrates consistent monopole-like radiation pattern in the whole working band, which is very suitable and well designed for indoor ceiling base station applications.- Open Access
- 4 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 7836-7844
Vertically Polarized Quasi-Yagi MIMO Antenna for 5G N78 Band Application
In this study, a three-port vertically polarized Quasi-Yagi Multiple-Input-Multiple-Output (MIMO) antenna system with pattern diversity is proposed for 5G N78 band application. All the three ports, which are sequentially rotated by 120°, are integrated together on a circle patch. Each antenna element is fed by a probe and an annular slot etched on the patch which works as a capacitor to counteract the inductance effect introduced by the feeding probe and the nearby shorting posts. A patch-like broadside radiation pattern is generated for each element. By introducing a novel$\Gamma $ -shaped metal plate for each element, the radiation beam could be tilted and deviate from the z axis by around +30° to suit the diversity application demand. Good isolation is achieved by introducing a metal post between every two ports, which well suppresses the mutual coupling induced by the current between the ports. The working principle of the proposed MIMO antenna is theoretically illustrated in detail and experimentally verified. The Proposed antenna occupies a cylindrical volume of$\pi \times 0.33^{2} \times 0.14\,\,\lambda _{0}^{3}$ , where$\lambda _{0}$ represents the free space wavelength at the center frequency of the operating band. The measured overlapping bandwidth covers the N78 band (3.3-3.8 GHz) with$\vert \text{S}_{11}\vert < -10$ dB for the three antenna elements. The proposed antenna offers attractive features including a shared radiation aperture, pattern diversity, good isolation ($\le20$ dB) good gain ($\ge8.2$ dBi), low field envelope correlation coefficient value ($\le0.001$ ), and high radiation efficiency ($\ge74$ %).- 4 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 7836-7844
Open AccessVertically Polarized Quasi-Yagi MIMO Antenna for 5G N78 Band Application
In this study, a three-port vertically polarized Quasi-Yagi Multiple-Input-Multiple-Output (MIMO) antenna system with pattern diversity is proposed for 5G N78 band application. All the three ports, which are sequentially rotated by 120°, are integrated together on a circle patch. Each antenna element is fed by a probe and an annular slot etched on the patch which works as a capacitor to counteract the inductance effect introduced by the feeding probe and the nearby shorting posts. A patch-like broadside radiation pattern is generated for each element. By introducing a novel$\Gamma $ -shaped metal plate for each element, the radiation beam could be tilted and deviate from the z axis by around +30° to suit the diversity application demand. Good isolation is achieved by introducing a metal post between every two ports, which well suppresses the mutual coupling induced by the current between the ports. The working principle of the proposed MIMO antenna is theoretically illustrated in detail and experimentally verified. The Proposed antenna occupies a cylindrical volume of$\pi \times 0.33^{2} \times 0.14\,\,\lambda _{0}^{3}$ , where$\lambda _{0}$ represents the free space wavelength at the center frequency of the operating band. The measured overlapping bandwidth covers the N78 band (3.3-3.8 GHz) with$\vert \text{S}_{11}\vert < -10$ dB for the three antenna elements. The proposed antenna offers attractive features including a shared radiation aperture, pattern diversity, good isolation ($\le20$ dB) good gain ($\ge8.2$ dBi), low field envelope correlation coefficient value ($\le0.001$ ), and high radiation efficiency ($\ge74$ %). - 7 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (2) , 169-173
A Low-Profile Vertically Polarized Antenna With Conical Radiation Pattern for Indoor Micro Base Station Application
A novel low-profile vertically polarized wideband monopole antenna is proposed. A central-fed circular patch antenna which is shorted concentrically by three metal pins is initially adopted to excite TM01 and TM02 modes. Then, a fan-shaped clearance area is cut out in the angular area between each two shorting pins. Finally, three mushroom-like structures are placed in the clearance area, which, together with the feeding probe, form three split ring resonators that introduce an extra resonance, thereby substantially expanding the antenna operation bandwidth. All the three modes have radiation patterns similar to the conventional monopole. The proposed antenna has a very low profile of 0.06 $λ_\text{min}$ and a lateral dimension of π × (0.176 $λ_\text{min}$ ) $^2$ , where $λ_\text{min}$ is the free space wavelength at the lowest frequency of operation. A simulated impedance bandwidth for |S $_\text{11}$ | <-10 dB of about 48.5% ranging from 1.7 to 2.79 GHz is achieved, which fully covers the 4G LTE band, while the measured result shows a wider fractional bandwidth of 66%.- 7 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (2) , 169-173
A Low-Profile Vertically Polarized Antenna With Conical Radiation Pattern for Indoor Micro Base Station Application
A novel low-profile vertically polarized wideband monopole antenna is proposed. A central-fed circular patch antenna which is shorted concentrically by three metal pins is initially adopted to excite TM01 and TM02 modes. Then, a fan-shaped clearance area is cut out in the angular area between each two shorting pins. Finally, three mushroom-like structures are placed in the clearance area, which, together with the feeding probe, form three split ring resonators that introduce an extra resonance, thereby substantially expanding the antenna operation bandwidth. All the three modes have radiation patterns similar to the conventional monopole. The proposed antenna has a very low profile of 0.06 $λ_\text{min}$ and a lateral dimension of π × (0.176 $λ_\text{min}$ ) $^2$ , where $λ_\text{min}$ is the free space wavelength at the lowest frequency of operation. A simulated impedance bandwidth for |S $_\text{11}$ | <-10 dB of about 48.5% ranging from 1.7 to 2.79 GHz is achieved, which fully covers the 4G LTE band, while the measured result shows a wider fractional bandwidth of 66%.- 14 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (12) , 2305-2309
A Low-Profile Wideband Antenna With Monopolelike Radiation Characteristics for 4G/5G Indoor Micro Base Station Application
A wideband, low-profile, vertically polarized antenna with monopole like radiation characteristics is proposed for 4G/5G indoor base station applications. The design of this antenna is based on the traditional monocone antenna with internal matching and reactive load. The structure of monocone is realized by crossed substrate, which reduces the antenna weight and improves the design flexibility simultaneously. Then, reactive loading of capacitively coupled triangle patches and shorting pins are used to reduce the height of antenna profile to 0.08λ min , where λ min is the free-space wavelength at the lowest operation frequency. An interdigital capacitor is etched near the antenna's input to adjust the impedance matching. The proposed antenna demonstrates consistent monopolelike, omnidirectional radiation patterns within the operating band. A measured impedance bandwidth for voltage standing-wave ratio (VSWR) <; 2.2 of about 81% ranging from 1.66 to 3.95 GHz is achieved, which covers 1.7-2.7 GHz 4G Long-Term Evolution band and 3.3-3.8 GHz 5G N78 band simultaneously. The proposed antenna is tailored for the ceiling micro base station in indoor distributed system.
- 14 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (12) , 2305-2309
A Low-Profile Wideband Antenna With Monopolelike Radiation Characteristics for 4G/5G Indoor Micro Base Station Application
A wideband, low-profile, vertically polarized antenna with monopole like radiation characteristics is proposed for 4G/5G indoor base station applications. The design of this antenna is based on the traditional monocone antenna with internal matching and reactive load. The structure of monocone is realized by crossed substrate, which reduces the antenna weight and improves the design flexibility simultaneously. Then, reactive loading of capacitively coupled triangle patches and shorting pins are used to reduce the height of antenna profile to 0.08λ min , where λ min is the free-space wavelength at the lowest operation frequency. An interdigital capacitor is etched near the antenna's input to adjust the impedance matching. The proposed antenna demonstrates consistent monopolelike, omnidirectional radiation patterns within the operating band. A measured impedance bandwidth for voltage standing-wave ratio (VSWR) <; 2.2 of about 81% ranging from 1.66 to 3.95 GHz is achieved, which covers 1.7-2.7 GHz 4G Long-Term Evolution band and 3.3-3.8 GHz 5G N78 band simultaneously. The proposed antenna is tailored for the ceiling micro base station in indoor distributed system.