Xiaomin Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiaomin Huang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Baoyu Wang
4 shared publicationsHongchao Ji
4 shared publicationsBen Guan
3 shared publications- Yong Zang
School of Mechanical Engineering, University of Science and Technology Beijing, Beijing, China
3 shared publications Junjie Qin
2 shared publicationsXiaoyue Lang
2 shared publications
Latest Publications
- 11 November 2026
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 27 (1)
Quantitative characterization of microstructural evolution and damage modeling of 2195 Al–Cu–Li alloy during hot deformation
- 11 November 2026
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 27 (1)
Quantitative characterization of microstructural evolution and damage modeling of 2195 Al–Cu–Li alloy during hot deformation
- Open Access
- 31 October 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 45, 7356-7374
Investigation on microstructural evolution during mandrel forging and residual heat normalizing process of hub bearings
- 31 October 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 45, 7356-7374
Open AccessInvestigation on microstructural evolution during mandrel forging and residual heat normalizing process of hub bearings
- Open Access
- 20 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 8768-8779
Comparative analysis of welding quality in Q235/20# dissimilar steel: Intermittent vs. full TIG welding
- 20 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 8768-8779
Open AccessComparative analysis of welding quality in Q235/20# dissimilar steel: Intermittent vs. full TIG welding
- 20 August 2023
- Published by Springer Nature
- p. 43-50
Research on the 5A06 Aluminum Alloy Thin-Walled Elbow in Cold Stamping Condition
- 20 August 2023
- Published by Springer Nature
- p. 43-50
Research on the 5A06 Aluminum Alloy Thin-Walled Elbow in Cold Stamping Condition
- Open Access
- 3 July 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 25, 4842-4859
Tensile instability and limit strain behavior of explosion-welded steel/Al plate considering interface defect characteristics
- 3 July 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 25, 4842-4859
Open AccessTensile instability and limit strain behavior of explosion-welded steel/Al plate considering interface defect characteristics
- 24 February 2023
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 946
Hot tensile deformation behavior, fracture mechanism and microstructural evolution of 2195 Al-Li alloy
- 24 February 2023
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 946
Hot tensile deformation behavior, fracture mechanism and microstructural evolution of 2195 Al-Li alloy
- 23 January 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 125 (5-6) , 2581-2592
Investigation of forming defects in 5A06 aluminum alloy cold stamping of thin-walled shell with corner
- 23 January 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 125 (5-6) , 2581-2592
Investigation of forming defects in 5A06 aluminum alloy cold stamping of thin-walled shell with corner
- Open Access
- 1 January 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (1) , 016534
Constitutive models and microstructure evolution of Ti-6Al-4V alloy during the hot compressive process
Using the Gleeble-1500D thermal simulation machine, and the Ti-6Al-4V titanium alloy was subjected to isothermal compression test under the conditions of deformation temperature of 1023 K–1323 K, strain rate of 0.01 s−1–10 s−1 and maximum deformation degree of 60% (the true strain is 0.916), and the stress and strain data under different deformation conditions were obtained. Based on the stress and strain data, the Arrhenius model and Back-Propagation Artificial Neural Network (BP-ANN) model were obtained. The results show that the BP-ANN model has higher accuracy than Arrhenius model, its correlation coefficient is as high as 0.99959, and the average absolute relative error is only 3.0935%. The Ti-6Al-4V titanium alloy model can make up for the lack of prediction accuracy of the constitutive model, and can predict the flow stress in all deformation ranges. Finally, the influence of different deformation temperature, deformation rate and deformation amount on microstructure is analyzed.
- 1 January 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (1) , 016534
Open AccessConstitutive models and microstructure evolution of Ti-6Al-4V alloy during the hot compressive process
Using the Gleeble-1500D thermal simulation machine, and the Ti-6Al-4V titanium alloy was subjected to isothermal compression test under the conditions of deformation temperature of 1023 K–1323 K, strain rate of 0.01 s−1–10 s−1 and maximum deformation degree of 60% (the true strain is 0.916), and the stress and strain data under different deformation conditions were obtained. Based on the stress and strain data, the Arrhenius model and Back-Propagation Artificial Neural Network (BP-ANN) model were obtained. The results show that the BP-ANN model has higher accuracy than Arrhenius model, its correlation coefficient is as high as 0.99959, and the average absolute relative error is only 3.0935%. The Ti-6Al-4V titanium alloy model can make up for the lack of prediction accuracy of the constitutive model, and can predict the flow stress in all deformation ranges. Finally, the influence of different deformation temperature, deformation rate and deformation amount on microstructure is analyzed.