UOUzodinma Okoroanyanwu

Uzodinma Okoroanyanwu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Uzodinma Okoroanyanwu has a total of 124 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Structural Lithium-Ion Batteries Prepared via Electrophoretic Deposition of LiFePO4/Reduced Graphene Oxide Composite Cathode and Graphene Anode on Carbon Cloth

    by Uzodinma Okoroanyanwu, Yu Tian, Varun Pande, James J. Watkins, Nianqiang Wu

    Structural lithium-ion pouch cell batteries based on binder-free LiFePO4/reduced graphene oxide composite cathode and graphene anode are prepared respectively via electrophoretic co-deposition of LiFePO4, reduced graphene oxide and carbon black on carbon cloth substrate for the cathode, graphene oxide and carbon black on carbon cloth substrate for the anode. Graphene oxide for the anode is electrochemically or photothermally reduced to graphene. The electrolyte is 1M LiPF6 in ethylene carbonate and dimethyl carbonate (50/50, v/v) with fluoroethylene carbonate as an additive. The separator is Celgard. Possessing excellent stiffness, strength-to-weight ratio, and good electrical conductivity, the carbon cloth substrate serves multifunctional roles: as current collectors for the anode and cathode, as structural reinforcement, flexibility, and mechanical load bearing element, as active material for lithiation/delithiation processes, and as high porosity and high surface area element for enhancement of Li-ion diffusion and mass transfer kinetics. Given its good electrical conductivity, high aspect ratio, and high surface area, reduced graphene oxide improves electrical conductivity within the cathode and provides sites for hosting LiFePO4; this enhances reversible Li ion extraction from the host during cycling. Graphene provides sites for insertion of Li ions in the anode; this enhances the aerial lithiation capacity of the battery system. Carbon black enhances conductivity within the two electrodes and reduces interfacial impedance. The electrochemical properties of the electrodes are strongly correlated to their microstructure and phase composition. Electrochemical characterization of the electrodes and their performance in full pouch cell battery configuration are evaluated, along with the utility of carbon cloth as a current collector.

  • (Invited) Structural Lithium-Ion Battery Based on LiFePO4/Reduced Graphene Oxide Composite Cathode and Graphene Anode Prepared via Electrophoretic Deposition on Carbon Cloth

    by Uzodinma Okoroanyanwu, Varun Pande, Claire Senger, James J. Watkins

    Structural lithium-ion batteries based on binder-free LiFePO4/reduced graphene oxide composite cathode electrode and graphene anode electrode are prepared respectively via electrophoretic co-deposition of LiFePO4, reduced graphene oxide, and carbon black on carbon cloth substrate for the cathode, and graphene oxide and carbon black on carbon cloth substrate for the anode. Following deposition, the electrode materials were dried. The graphene oxide of the anode was reduced to graphene via rapid thermal annealing. Possessing excellent stiffness, strength-to-weight ratio, and good electrical conductivity, the carbon cloth substrate serves multifunctional roles in the battery: as structural reinforcement and mechanical load bearing element and as current collector. Given its good electrical conductivity, high aspect ratio, and high surface area, reduced graphene oxide improves electrical conductivity within the cathode and provides sites for hosting LiFePO4; this enhances reversible Li ion extraction from the host during cycling. Graphene with its good electrical conductivity and high aspect ratio provides sites for insertion of Li ions in the anode; this enhances the aerial lithiation capacity of the battery system. Carbon black enhances conductivity within the two electrodes and reduces interfacial impedance. The electrochemical properties of the electrodes are strongly correlated to their microstructure and phase composition. Electrochemical characterization of the electrodes and their performance in half-cell and full cell configurations are evaluated. Additionally, Li-ion diffusivity within the materials is evaluated with three independent electroanalytical methods, including potentiostatic and galvanostatic and intermittent titration techniques, and electrochemical impedance spectroscopy.

  • Additive manufacturing of high performance metalenses, waveguides and metamaterials via direct nanoimprint lithography

    by Dae-Eon Jung, Vince Einck, Lucas Verrastro, Uzodinma Okoroanyanwu, Amir Arbabi, James J. Watkins

    We fabricate all-inorganic, high refractive index optics, including metalenses, waveguides, and diffractive optical elements via nanoimprint lithography with TiO2 nanoparticle dispersion inks and report full-wafer fabrication of visible wavelength metalenses with absolute focusing efficiencies greater than 80% (>95% of design efficiency). 3-D metal oxide log-piles are possible via direct NIL using sequential imprint, planarization, imprint cycles followed by removal of the sacrificial planarization layers. 3-D metal log-piles are possible via metallization of imprinted 3-D sacrificial templates. Several examples will be discussed.

  • Large Area Millisecond Preparation of High-Quality, Few-Layer Graphene Films on Arbitrary Substrates via Xenon Flash Lamp Photothermal Pyrolysis and Their Application for High-Performance Micro-supercapacitors

    by Uzodinma Okoroanyanwu, Ayush Bhardwaj, James J. Watkins

    We report a method for fast, efficient, and scalable preparation of high-quality, large area, few-layer graphene films on arbitrary substrates via high-intensity pulsed xenon flash lamp photothermal pyrolysis of thin precursor films at ambient conditions in millisecond time frames. The precursors comprised poly(2,2-bis(3,4-dihydro-3-phenyl-1,3-benzoxazine)), and cyclized polyacrylonitrile and possess significant absorption cross section within the bandwidth of the emission spectrum of a xenon flash lamp. By localizing light absorption to the precursor films, the process enabled the preparation of few-layer graphene films on any substrate, including thermally sensitive substrates without the need for any catalytic substrate as in chemical vapor deposition-based approaches or conductive electrodes as in electrochemical method-based approaches. The extent of conversion of the precursor films to graphene was strongly dependent on pulse energy and the local temperature achieved due to photothermal effect, which were controlled via pulse power modulation; it also depended on structural properties of the precursor and to a lesser extent on the substrate. The cPAN showed a higher efficiency for conversion to graphene, as confirmed by Raman spectra (ID/IG ∼ 0.3), and sheet resistance of 0.1 Ω cm. To demonstrate the utility of the process, graphene film electrodes prepared photothermally on carbon fiber current collector were used for the fabrication of micro-supercapacitors with a very high areal supercapacitance of 3.5 mF/cm2. Subsequent deposition of manganese oxide onto the fabricated electrodes significantly increased the energy storage capability of the supercapacitor, yielding a device with exceptionally high capacitance of 80 F/g at 1 mA current, good rate capability, and long cycle life.


  • Open Access

    Chemistry and Lithography, Second Edition, Vol. 1: The Chemical History of Lithography

    by Uzodinma Okoroanyanwu

    This book is the first in a series of three volumes that make up the second edition of Chemistry and Lithography (2010). Although it is continued in Vol. 2, Chemistry in Lithography , and Vol. 3, The Practice of Lithography, each volume stands on its own. Volume 1 of the second edition weaves together threads of a narrative on the history of optical and molecular physics, optical technology, chemistry, and lithography, with the aim to give readers new insight into an aspect of the relationships between these fields that is often not fully appreciated: how the marriage of chemistry and optics led to the development and evolution of lithography. The book shows how major developments in chemistry, physics, and the technology of light have influenced the invention and development of lithography well beyond what its inventor envisioned. It also shows how developments in lithography have not only influenced the development of optics and chemistry, but also have played a critical role in the large-scale manufacture of integrated circuits that run the computers and machineries on which our modern electronic and information age depend. Finally, this book provides an analysis of the emerging trends in lithographic patterning, along with the current and potential applications of the resulting patterned structures and surfaces.


  • Introduction to Lithography

    by Uzodinma Okoroanyanwu

    It is hard to think of an invention that has had a greater influence on the mass production of devices that have enabled humankind to communicate information with printed matter or photons or electrons or ions, or even with atoms, than lithography. The information superhighway and pathways of our present age—the information age—are literally paved with chips of crystalline silicon by lithography. Nearly every book, magazine, newspaper, brochure, flyer, catalog, and other print pieces that have been produced during the last 300 years and before the digital age of the last few decades have been printed with offset lithography. Nearly every integrated circuit (IC) in the chips that run the computers and telecommunication systems that power the information superhighway, as well as medical devices, electronics, home and industrial appliances, automobiles, and airplanes—to mention but a few—are made by semiconductor lithography. Without such ICs, we would have no powerful computers, no large-scale automation, no communication satellites, nor even any space exploration. There would certainly be no electronic calculators or digital watches, no transistor radios, portable tape recorders, personal digital assistants, internet, cell phones, etc. Many diagnostic procedures in medicine and dentistry rely on ICs, as do heart pacemakers and modern hearing aids. The impact of all of these things on our lives is tremendous. For instance, we can watch events on our television sets or mobile phones, or on the Internet, as they are happening thousands of miles away. We can withdraw our money from automatic teller machines almost everywhere in the world, without the aid of a bank clerk, whose function has been transformed from that of an accounts keeper to one of an intermediary between the customer and the computer. Many products are now manufactured, assembled, and shipped today by automatic machines that rely on ICs for their operation. Airplanes are guided by computer-controlled systems, and even airline seats are reserved worldwide by an instantaneous computer booking system. The list is almost endless and is growing every day. A world without lithography would be unrecognizable to anyone of us today, although we may not always be cognizant of its pervasiveness and reach in our daily lives. Lithography underpins most of the technical inventory of modern life. Online access to SPIE eBooks is limited to subscribing institutions.

  • Evolution of Lithography

    by Uzodinma Okoroanyanwu

    From the time of Senefelder to the present, lithography has undergone tremendous evolution, but overall, its basic principle remains intact. It remains a planographic printing process in which the image and nonimage areas are on the same plane of the printing substrate. Just as in Senefelder’s time, today, the contrast between the image and nonimage areas depends on the interfacial tension of oily inks and water-retaining surfaces. This is in fact the very same principle that governs the immiscibility of oil and water— hydrophobic–hydrophilic interactions between the image and nonimage areas. The inks (or resist) are naturally hydrophobic and can be made resistant to the action of etchants when dry. Online access to SPIE eBooks is limited to subscribing institutions.


  • Open Access

    Front Matter

    by Uzodinma Okoroanyanwu

    This section contains the title page, dedication, table of contents, preface, and list of acronyms and abbreviations. PDF download only.

  • Physical Origins of Lithography

    by Uzodinma Okoroanyanwu

    As stated in Chapter 1, the so-called information superhighway is paved with chips of crystalline silicon by lithography, for it is the key technology process step with which we are able to create fine-patterned structures that ultimately form the devices and interconnects of complex functional integrated circuits (ICs) used in microelectronics. As a matter of fact, both circuit speed and integration density depend on the size of the lithographic minimum-printable feature. Today lithography represents over 35% of the chip manufacturing cost in the semiconductor industry. The increasing cost of lithographic exposure tools is recognized as one of the most critical factors for keeping up with Moore’s law. Online access to SPIE eBooks is limited to subscribing institutions.