Shaohua Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shaohua Wang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Xiaonv Li
School of Materials Science and Engineering Jingdezhen Ceramic University Jingdezhen China
2 shared publicationsChao Wang
School of Materials Science and Engineering Jingdezhen Ceramic Institute Jingdezhen China
1 shared publication- Fei Hu
School of Materials and Energy, Foshan University, Foshan, China
1 shared publication Feng Wang
School of Materials Science and Engineering Jingdezhen Ceramic University Jingdezhen China
1 shared publication- Guohong Zhang
The State Key Laboratory for Refractories and Metallurgy, Hubei Collaborative Innovation Center on Advanced Steels, International Research Institute for Steel Technology, Wuhan University of Science and Technology, Wuhan 430081, China
1 shared publication Qibing Chang
School of Materials Science and Engineering Jingdezhen Ceramic Institute Jingdezhen China
1 shared publication
Latest Publications
- 13 November 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 23 (1)
Development of Zr‐free augite glass‐ceramic glaze with high opacity for ceramic tiles
The development of cost‐effective, nonradioactive zirconium (Zr)‐free opaque glazes represents a critical objective for sustainable ceramic manufacturing. This study successfully prepared an augite‐based glass‐ceramic glaze within the CaO–MgO–Al 2 O 3 –SiO 2 system using economical industrial raw materials. The glaze was prepared via a frit route, involving melting the raw materials, quenching the melt to obtain a frit, ball‐milling the frit into a slurry, and finally dip‐coating and firing. Systematic investigation revealed that firing at 1150°C produced an optimal microstructure dominated by augite (24.9 wt.%) and cristobalite (20.4 wt.%) crystals, with a refined grain size of ∼1.4 µm. The resulting glaze exhibited properties comparable to conventional ZrSiO 4 ‐based systems, achieving a superior L * value of 89.21 (+77.6% vs. ceramic body), whiteness of 76.1% (+561.7% vs. ceramic body), and Vickers hardness of 7.10 GPa. These findings confirm that augite‐based opaque glazes are a technically viable and more sustainable alternative, offering valuable insights for the development of low‐temperature‐fired, Zr‐free ceramic glazes.
- 13 November 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 23 (1)
Development of Zr‐free augite glass‐ceramic glaze with high opacity for ceramic tiles
The development of cost‐effective, nonradioactive zirconium (Zr)‐free opaque glazes represents a critical objective for sustainable ceramic manufacturing. This study successfully prepared an augite‐based glass‐ceramic glaze within the CaO–MgO–Al 2 O 3 –SiO 2 system using economical industrial raw materials. The glaze was prepared via a frit route, involving melting the raw materials, quenching the melt to obtain a frit, ball‐milling the frit into a slurry, and finally dip‐coating and firing. Systematic investigation revealed that firing at 1150°C produced an optimal microstructure dominated by augite (24.9 wt.%) and cristobalite (20.4 wt.%) crystals, with a refined grain size of ∼1.4 µm. The resulting glaze exhibited properties comparable to conventional ZrSiO 4 ‐based systems, achieving a superior L * value of 89.21 (+77.6% vs. ceramic body), whiteness of 76.1% (+561.7% vs. ceramic body), and Vickers hardness of 7.10 GPa. These findings confirm that augite‐based opaque glazes are a technically viable and more sustainable alternative, offering valuable insights for the development of low‐temperature‐fired, Zr‐free ceramic glazes.
- Open Access
Corrosion and Interfacial Contact Resistance of NiTi Alloy as a Promising Bipolar Plate for PEMFC
Titanium (Ti) is generally considered as an ideal bipolar plate (BPP) material because of its excellent corrosion resistance, good machinability and lightweight nature. However, the easy-passivation property, which leads to increased interfacial contact resistance (ICR) and subsequently decreased cell performance, limits its large-scale commercial application in proton exchange membrane fuel cells (PEMFCs). In this paper, we proposed a NiTi alloy prepared by suction casting as a promising bipolar plate for PEMFCs. This NiTi alloy exhibits significantly decreased ICR values (16.8 mΩ cm2 at 1.4 MPa) compared with pure Ti (88.6 mΩ cm2 at 1.4 MPa), along with enhanced corrosion resistance compared with pure nickel (Ni). The superior corrosion resistance of NiTi alloy is accredited to the nobler open circuit potential and corrosion potential, coupled with low corrosion current densities and passive current densities. The improved ICR can be interpreted by the existence of high-proportioned metallic Ni in the passive film, which contributes to the reduced capacitance characteristic of the passive film (compared with Ti) and enhances charge conduction. This work provides a feasible option to ameliorate BPP material that may have desirable corrosion resistance and ICR.
Open AccessCorrosion and Interfacial Contact Resistance of NiTi Alloy as a Promising Bipolar Plate for PEMFC
Titanium (Ti) is generally considered as an ideal bipolar plate (BPP) material because of its excellent corrosion resistance, good machinability and lightweight nature. However, the easy-passivation property, which leads to increased interfacial contact resistance (ICR) and subsequently decreased cell performance, limits its large-scale commercial application in proton exchange membrane fuel cells (PEMFCs). In this paper, we proposed a NiTi alloy prepared by suction casting as a promising bipolar plate for PEMFCs. This NiTi alloy exhibits significantly decreased ICR values (16.8 mΩ cm2 at 1.4 MPa) compared with pure Ti (88.6 mΩ cm2 at 1.4 MPa), along with enhanced corrosion resistance compared with pure nickel (Ni). The superior corrosion resistance of NiTi alloy is accredited to the nobler open circuit potential and corrosion potential, coupled with low corrosion current densities and passive current densities. The improved ICR can be interpreted by the existence of high-proportioned metallic Ni in the passive film, which contributes to the reduced capacitance characteristic of the passive film (compared with Ti) and enhances charge conduction. This work provides a feasible option to ameliorate BPP material that may have desirable corrosion resistance and ICR.
- 11 January 2021
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 18 (3) , 1052-1062
Phase composition, microstructure, and properties of ceramic tile prepared using ceramic polishing waste as raw material
Polished ceramic products are currently the most popular in architectural decoration, but a significant amount of ceramic polishing waste (CPW) is produced during the preparation process. Determining how to handle the CPW is a pressing task for enterprises. This work investigated the feasibility of recycling CPW in porcelain tile, and its influence on the phase composition, microstructure, and properties of the ceramic body. The CPW was found to have a similar composition to the traditional ceramics and worked as a flux. The SiC within CPW began to decompose into SiO2 with CO2 generation at about 1100°C, resulting in a porous structure. Microstructure observation indicated that a high CPW sample produced sufficient liquid phase when fired at temperatures ≤1100°C, which was not only beneficial for mullite growth but also for matrix densification by the viscous flow mechanism. But a high‐content CPW caused the body to foam or even expand at temperatures >1100°C, thus significantly reducing mechanical properties. Finally, a series of porcelain tiles were successfully prepared with a CPW content of ≤30 wt% at a firing temperature of 1125‐1200°C. The results of this study are considered to be valuable for the utilization of CPW.
- 11 January 2021
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 18 (3) , 1052-1062
Phase composition, microstructure, and properties of ceramic tile prepared using ceramic polishing waste as raw material
Polished ceramic products are currently the most popular in architectural decoration, but a significant amount of ceramic polishing waste (CPW) is produced during the preparation process. Determining how to handle the CPW is a pressing task for enterprises. This work investigated the feasibility of recycling CPW in porcelain tile, and its influence on the phase composition, microstructure, and properties of the ceramic body. The CPW was found to have a similar composition to the traditional ceramics and worked as a flux. The SiC within CPW began to decompose into SiO2 with CO2 generation at about 1100°C, resulting in a porous structure. Microstructure observation indicated that a high CPW sample produced sufficient liquid phase when fired at temperatures ≤1100°C, which was not only beneficial for mullite growth but also for matrix densification by the viscous flow mechanism. But a high‐content CPW caused the body to foam or even expand at temperatures >1100°C, thus significantly reducing mechanical properties. Finally, a series of porcelain tiles were successfully prepared with a CPW content of ≤30 wt% at a firing temperature of 1125‐1200°C. The results of this study are considered to be valuable for the utilization of CPW.