Saad G. Muttlak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Saad G. Muttlak has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Mohammed Missous
Department of Electrical and Electronic Engineering, University of Manchester, Manchester M13 9PL, UK
17 shared publications - Omar S. Abdulwahid
Department of Mechatronics Engineering, College of Engineering University of Mosul Mosul Iraq
12 shared publications J. Sexton
School of Electrical and Electronic Engineering, University of Manchester, Manchester, M13 9PL, UK
11 shared publicationsJames Sexton
3 shared publicationsM. J. Kelly
3 shared publications- Abdelmajid Salhi
HBKU Core Laboratories
2 shared publications
Latest Publications
- 12 October 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
On‐Chip Ultra Small 900‐MHz Wireless Powering Transfer for Smart Biomedical Devices
A compact rectenna operating at 900 MHz for wireless powered implantable devices is presented. With the bending technique of the antenna arms, the proposed rectenna volume was effectively miniaturized to only 3.13 mm 3 , establishing the smallest reported structure to date compared with literature at a similar band frequency. A monolithic integration scheme was employed, yielding a compact footprint of 250 μm × 850 μm. To achieve accurate impedance optimisation for maximum power transfer, the electrical characteristics of the incorporated elements were comprehensively characterized over a wide range of operating frequencies and input power levels. The proposed design methodology demonstrates a matching‐less rectenna integration circuitry, which aided in further reduction in the ultimate volume. Four samples have been explored, and 2 × 15 mm 2 design shows a superior low power reflection of 0.1%, which resulted in a high output voltage and power conversion efficiency of 0.84% and 7.92% at a load resistance of 14 kΩ, respectively. The maximum experimental power transmitted efficiency (PTE) of 0.0013% was obtained for the 5‐mm 2 design, corresponding to a 0.2‐V output voltage at 20‐dBm transmitted power. With a 2 × 15 mm 2 design, the rectenna delivers high PTE of 0.0504%, demonstrating competitive performance together with a significant reduction in the implementation complexity for self‐powered implanted devices.
- 12 October 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
On‐Chip Ultra Small 900‐MHz Wireless Powering Transfer for Smart Biomedical Devices
A compact rectenna operating at 900 MHz for wireless powered implantable devices is presented. With the bending technique of the antenna arms, the proposed rectenna volume was effectively miniaturized to only 3.13 mm 3 , establishing the smallest reported structure to date compared with literature at a similar band frequency. A monolithic integration scheme was employed, yielding a compact footprint of 250 μm × 850 μm. To achieve accurate impedance optimisation for maximum power transfer, the electrical characteristics of the incorporated elements were comprehensively characterized over a wide range of operating frequencies and input power levels. The proposed design methodology demonstrates a matching‐less rectenna integration circuitry, which aided in further reduction in the ultimate volume. Four samples have been explored, and 2 × 15 mm 2 design shows a superior low power reflection of 0.1%, which resulted in a high output voltage and power conversion efficiency of 0.84% and 7.92% at a load resistance of 14 kΩ, respectively. The maximum experimental power transmitted efficiency (PTE) of 0.0013% was obtained for the 5‐mm 2 design, corresponding to a 0.2‐V output voltage at 20‐dBm transmitted power. With a 2 × 15 mm 2 design, the rectenna delivers high PTE of 0.0504%, demonstrating competitive performance together with a significant reduction in the implementation complexity for self‐powered implanted devices.
- Open Access
Miniature Integrated 2.4 GHz Rectennas Using Novel Tunnel Diodes
This work presents the design, fabrication, and measured results of a fully integrated miniature rectenna using a novel tunnel diode known as the Asymmetrical Spacer Layer Tunnel (ASPAT). The term rectenna is an abbreviation for a rectifying antenna, a device with a rectifier and antenna coexisting as a single design. The ASPAT is the centrepiece of the rectifier used for its strong temperature independence, zero bias, and high dynamic range. The antenna is designed to be impedance matched with the rectifier, eliminating the need for a matching network and saving valuable real estate on the gallium arsenide (GaAs) substrate. The antenna is fully integrated with the rectifier on a single chip, thus enabling antenna miniaturisation due to the high dielectric constant of GaAs and spiral design. This miniaturisation enables the design to be fabricated economically on a GaAs substrate whilst being comparable in size to a 15-gauge needle, thus unlocking applications in medical implants. The design presented here has a total die size of 4 × 1.2 mm2, with a maximum measured output voltage of 0.97 V and a 20 dBm single-tone 2.35 GHz signal transmitted 5 cm away from the rectenna.
Open AccessMiniature Integrated 2.4 GHz Rectennas Using Novel Tunnel Diodes
This work presents the design, fabrication, and measured results of a fully integrated miniature rectenna using a novel tunnel diode known as the Asymmetrical Spacer Layer Tunnel (ASPAT). The term rectenna is an abbreviation for a rectifying antenna, a device with a rectifier and antenna coexisting as a single design. The ASPAT is the centrepiece of the rectifier used for its strong temperature independence, zero bias, and high dynamic range. The antenna is designed to be impedance matched with the rectifier, eliminating the need for a matching network and saving valuable real estate on the gallium arsenide (GaAs) substrate. The antenna is fully integrated with the rectifier on a single chip, thus enabling antenna miniaturisation due to the high dielectric constant of GaAs and spiral design. This miniaturisation enables the design to be fabricated economically on a GaAs substrate whilst being comparable in size to a 15-gauge needle, thus unlocking applications in medical implants. The design presented here has a total die size of 4 × 1.2 mm2, with a maximum measured output voltage of 0.97 V and a 20 dBm single-tone 2.35 GHz signal transmitted 5 cm away from the rectenna.
- 27 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (17) , 16938-16944
Low-Cost Compact Integrated Rectenna for Implantable Medical Receivers
This work describes a novel fully integrated rectenna circuit using tunnelling-based devices for implanted medical devices. An ASPAT (Asymmetric Spacer Layer Tunnel Diode) was used as the active rectifier due to its high non-linearity and temperature insensitivity features. A miniaturized geometry rectenna (1×5mm2) with improved matching characteristics was demonstrated, by integrating a Cockcroft-Walton rectifier with an L-shaped planar folded antenna structure operating at ISM frequency bands. The circuit performance was experimentally explored at various separation distance between transmitter and receiver units. For a 5cm transmission set-up, the rectenna with a single-stage rectifier delivered 0.8V output at 20dBm transmit power. An extended doubler configuration exhibited enhanced performance when multiple stages are used, is predicted to reach 0.24mW output power at 23dBm transmit power and yielding ~1.6V output voltage with an efficiency of 0.12%. These findings can assist in compensating for the degraded antenna gain attributed to the extremely small effective-radiating area of 0.04λ. Furthermore, the ability of controlling the antenna input impedance helps in circumventing the requirement for a matching circuitry thereby offering further reduction in chip size.
- 27 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (17) , 16938-16944
Low-Cost Compact Integrated Rectenna for Implantable Medical Receivers
This work describes a novel fully integrated rectenna circuit using tunnelling-based devices for implanted medical devices. An ASPAT (Asymmetric Spacer Layer Tunnel Diode) was used as the active rectifier due to its high non-linearity and temperature insensitivity features. A miniaturized geometry rectenna (1×5mm2) with improved matching characteristics was demonstrated, by integrating a Cockcroft-Walton rectifier with an L-shaped planar folded antenna structure operating at ISM frequency bands. The circuit performance was experimentally explored at various separation distance between transmitter and receiver units. For a 5cm transmission set-up, the rectenna with a single-stage rectifier delivered 0.8V output at 20dBm transmit power. An extended doubler configuration exhibited enhanced performance when multiple stages are used, is predicted to reach 0.24mW output power at 23dBm transmit power and yielding ~1.6V output voltage with an efficiency of 0.12%. These findings can assist in compensating for the degraded antenna gain attributed to the extremely small effective-radiating area of 0.04λ. Furthermore, the ability of controlling the antenna input impedance helps in circumventing the requirement for a matching circuitry thereby offering further reduction in chip size.
- Open Access
- 1 June 2021
- Published by Elsevier in Physica E: Low-dimensional Systems and Nanostructures
- Vol. 130, 114723
Design and analysis of GaAs/AlAs asymmetric spacer layer tunnel diodes for high-frequency detection
- 1 June 2021
- Published by Elsevier in Physica E: Low-dimensional Systems and Nanostructures
- Vol. 130, 114723
Open AccessDesign and analysis of GaAs/AlAs asymmetric spacer layer tunnel diodes for high-frequency detection
- Open Access
- 21 May 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (19) , 194505
InGaAs/AlAs/GaAs metamorphic asymmetric spacer layer tunnel (mASPAT) diodes for microwaves and millimeter-waves detection
We present work on a novel In0.53Ga0.47As/AlAs metamorphic asymmetric spacer layer tunnel (mASPAT) diode structure, which was grown on GaAs by solid source molecular beam epitaxy. mASPAT diodes with different mesa sizes were fabricated and tested following growth under optimal conditions. The measured I–V characteristics of these tunneling devices showed rectifying behavior resulting from the asymmetric design of the epitaxial spacer layers. The extracted curvature coefficient, junction resistance, and leakage currents at −1 V resulted in an estimated theoretical cut-off frequency at zero bias exceeding 180 GHz for 4 × 4 μm2 mesa devices. The obtained results demonstrate the potential use of mASPAT devices on GaAs as a low-cost alternative to devices fabricated on InP substrates for high-volume zero bias microwave and millimeter-wave detectors.- 21 May 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (19) , 194505
Open AccessInGaAs/AlAs/GaAs metamorphic asymmetric spacer layer tunnel (mASPAT) diodes for microwaves and millimeter-waves detection
We present work on a novel In0.53Ga0.47As/AlAs metamorphic asymmetric spacer layer tunnel (mASPAT) diode structure, which was grown on GaAs by solid source molecular beam epitaxy. mASPAT diodes with different mesa sizes were fabricated and tested following growth under optimal conditions. The measured I–V characteristics of these tunneling devices showed rectifying behavior resulting from the asymmetric design of the epitaxial spacer layers. The extracted curvature coefficient, junction resistance, and leakage currents at −1 V resulted in an estimated theoretical cut-off frequency at zero bias exceeding 180 GHz for 4 × 4 μm2 mesa devices. The obtained results demonstrate the potential use of mASPAT devices on GaAs as a low-cost alternative to devices fabricated on InP substrates for high-volume zero bias microwave and millimeter-wave detectors. - 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
24GHz Zero-Bias Asymmetrical Spacer Layer Tunnel Diode Detectors
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
24GHz Zero-Bias Asymmetrical Spacer Layer Tunnel Diode Detectors
- Open Access
- 1 June 2019
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 13 (3) , 144-150
Low‐cost InP–InGaAs PIN–HBT‐based OEIC for up to 20 Gb/s optical communication systems
A detailed study of the performance analysis of a low‐cost PIN/heterojunction bipolar transistor (HBT) opto‐electronic integated circuit (OEIC) is described. Measured and of 54 and 57 GHz for 10 × 10 µm 2 HBTs were achieved for such a large emitter size. The base and collector regions of the transistor were utilised to form a PIN photodiode which has a dc responsivity and quantum efficiency of 0.5 A/W and 0.45, respectively, without antireflection coating at a wavelength of 1.55 µm. For both active devices, a model was realised taking all parasitic and physical‐based impacts into account, for example, equivalent circuit of the pads surrounding the devices and transit delay time across the collector depletion region. The simulation results of the discrete passive and active elements showed good agreement with experimental measurements. The OEIC module was implemented in Keysight‐advanced design system software with a three‐stage preamplifier which has a transimpedance gain of 40 dB Ω and a −3 dB bandwidth of 18 GHz. This corresponds to a transimpedance‐gain product of 1.8 THz. A series peaking inductor technique was used in the design, contributing to an enhancement in the opto‐electrical bandwidth of >60%. The optical/electrical response offers a bandwidth of ∼15 GHz, adequate for up to 20 Gb/s data rate operation.
- 1 June 2019
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 13 (3) , 144-150
Open AccessLow‐cost InP–InGaAs PIN–HBT‐based OEIC for up to 20 Gb/s optical communication systems
A detailed study of the performance analysis of a low‐cost PIN/heterojunction bipolar transistor (HBT) opto‐electronic integated circuit (OEIC) is described. Measured and of 54 and 57 GHz for 10 × 10 µm 2 HBTs were achieved for such a large emitter size. The base and collector regions of the transistor were utilised to form a PIN photodiode which has a dc responsivity and quantum efficiency of 0.5 A/W and 0.45, respectively, without antireflection coating at a wavelength of 1.55 µm. For both active devices, a model was realised taking all parasitic and physical‐based impacts into account, for example, equivalent circuit of the pads surrounding the devices and transit delay time across the collector depletion region. The simulation results of the discrete passive and active elements showed good agreement with experimental measurements. The OEIC module was implemented in Keysight‐advanced design system software with a three‐stage preamplifier which has a transimpedance gain of 40 dB Ω and a −3 dB bandwidth of 18 GHz. This corresponds to a transimpedance‐gain product of 1.8 THz. A series peaking inductor technique was used in the design, contributing to an enhancement in the opto‐electrical bandwidth of >60%. The optical/electrical response offers a bandwidth of ∼15 GHz, adequate for up to 20 Gb/s data rate operation.
- Open Access
- 1 February 2019
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 13 (1) , 40-45
Physical modelling of InGaAs–InAlAs APD and PIN photodetectors for >25 Gb/s data rate applications
Validated SILVACO physical models were exploited to optimise electrical and optical characteristics of 1.5 µm wavelength InAlAs–InGaAs Avalanche photodiodes and InGaAs PIN diodes. Optimised SILVACO models were created by selectively thinning down the absorption layers to further reduce the carrier transit time. Further optimisation was accomplished by scaling the light window aperture and mesa area sizes with the aim of reducing the device capacitances. The optimised PIN diode provides a maximum opto‐electric bandwidth of 35 GHz with a current responsivity of 0.4 A/W under −5 V bias voltage and 10 µW incident optical power. At 1 µW incident optical power, the maximum opto‐electric bandwidth and current responsivity of the optimised avalanche diode is 21 GHz and 1.4 A/W under −21.5 V bias voltage. The optimised APD and PIN photo‐detectors are capable of working at a data rate of up to 25 and 40 Gb/s, respectively.
- 1 February 2019
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 13 (1) , 40-45
Open AccessPhysical modelling of InGaAs–InAlAs APD and PIN photodetectors for >25 Gb/s data rate applications
Validated SILVACO physical models were exploited to optimise electrical and optical characteristics of 1.5 µm wavelength InAlAs–InGaAs Avalanche photodiodes and InGaAs PIN diodes. Optimised SILVACO models were created by selectively thinning down the absorption layers to further reduce the carrier transit time. Further optimisation was accomplished by scaling the light window aperture and mesa area sizes with the aim of reducing the device capacitances. The optimised PIN diode provides a maximum opto‐electric bandwidth of 35 GHz with a current responsivity of 0.4 A/W under −5 V bias voltage and 10 µW incident optical power. At 1 µW incident optical power, the maximum opto‐electric bandwidth and current responsivity of the optimised avalanche diode is 21 GHz and 1.4 A/W under −21.5 V bias voltage. The optimised APD and PIN photo‐detectors are capable of working at a data rate of up to 25 and 40 Gb/s, respectively.