Temitayo Elizabeth Oladimeji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Temitayo Elizabeth Oladimeji has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
John B. Adeoye
Department of Chemical and Energy Engineering, Curtin University, Miri, Malaysia
2 shared publications- Moses Eterigho Emetere
Department of Physics Bowen University Iwo Nigeria
2 shared publications Muyiwa Fajobi
2 shared publications- Olayemi Abosede Odunlami
Covenant University
2 shared publications Olayemi Odunlami
2 shared publications- Olubunmi Grace Abatan
Covenant University
2 shared publications
Latest Publications
- Open Access
- 13 February 2026
- Published by Bentham Science Publishers Ltd. in The Open Chemical Engineering Journal
- Vol. 20 (1)
Removal of Heavy Metals from Foundry Wastewater using Magnetic Graphene Oxide
Introduction: This research paper explores the potential of heavy metals removal from foundry effluents using graphene oxide (GO) and magnetic graphene oxide (MGO) as adsorbents. Methods: The preparation of graphene oxide (GO) was performed by the modified Hummers method, while that of magnetic graphene oxide (MGO) was done through coprecipitation methods, with analysis confirming its usefulness in removing metal ions. The influence of contact time, adsorbent dosage, and temperature on the heavy metal removal efficiency was subsequently investigated. The GO and MGO were further characterized using Fourier Transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) analyses. Results: The observed results pointed to GO demonstrating comparatively better removal efficiencies than MGO for Cr, Fe, Pb, Cd, and Zn: 95.40%, 94.00%, 95.80%, 94.2%, and 95.7%, respectively, compared to 88.70%, 87.4%, 90.2%, 90.7%, and 91.2%. Successful synthesis of graphene oxide (GO) and magnetic graphene oxide (MGO) was confirmed by using characterization techniques such as SEM, BET, and FTIR. The morphology and high surface area of GO with a flake-like structure were observed, whereas successful modification of iron nanoparticles onto MGO was observed with a high specific surface area of 1165.220 m2/g and an abundance of surface functional groups. Discussion: The heavy metals, which originate from foundry wastes, are removed from the wastewater by using the method of magnetic graphene oxide in this study. Various characterization methods, including SEM, BET, and FTIR, are studied. The parameters affecting the removal of heavy metals are the contact time, adsorbent dosage, and temperature. Contact time increases the opportunity to interact between the adsorbent and metal ions with a longer duration, whereas the number of active sites available to adsorb the heavy metal increases since the adsorbent dosage is higher, thereby increasing the efficiency of removal. Conclusion: The adsorption could be described in the manner of the Langmuir isotherm and pseudo-second-order kinetics, which depicts MGO's successful removal of heavy metals from foundry wastewater.
- 13 February 2026
- Published by Bentham Science Publishers Ltd. in The Open Chemical Engineering Journal
- Vol. 20 (1)
Open AccessRemoval of Heavy Metals from Foundry Wastewater using Magnetic Graphene Oxide
Introduction: This research paper explores the potential of heavy metals removal from foundry effluents using graphene oxide (GO) and magnetic graphene oxide (MGO) as adsorbents. Methods: The preparation of graphene oxide (GO) was performed by the modified Hummers method, while that of magnetic graphene oxide (MGO) was done through coprecipitation methods, with analysis confirming its usefulness in removing metal ions. The influence of contact time, adsorbent dosage, and temperature on the heavy metal removal efficiency was subsequently investigated. The GO and MGO were further characterized using Fourier Transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) analyses. Results: The observed results pointed to GO demonstrating comparatively better removal efficiencies than MGO for Cr, Fe, Pb, Cd, and Zn: 95.40%, 94.00%, 95.80%, 94.2%, and 95.7%, respectively, compared to 88.70%, 87.4%, 90.2%, 90.7%, and 91.2%. Successful synthesis of graphene oxide (GO) and magnetic graphene oxide (MGO) was confirmed by using characterization techniques such as SEM, BET, and FTIR. The morphology and high surface area of GO with a flake-like structure were observed, whereas successful modification of iron nanoparticles onto MGO was observed with a high specific surface area of 1165.220 m2/g and an abundance of surface functional groups. Discussion: The heavy metals, which originate from foundry wastes, are removed from the wastewater by using the method of magnetic graphene oxide in this study. Various characterization methods, including SEM, BET, and FTIR, are studied. The parameters affecting the removal of heavy metals are the contact time, adsorbent dosage, and temperature. Contact time increases the opportunity to interact between the adsorbent and metal ions with a longer duration, whereas the number of active sites available to adsorb the heavy metal increases since the adsorbent dosage is higher, thereby increasing the efficiency of removal. Conclusion: The adsorption could be described in the manner of the Langmuir isotherm and pseudo-second-order kinetics, which depicts MGO's successful removal of heavy metals from foundry wastewater.
- Open Access
- 10 November 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (11) , 1-27
From origin to oversight: properties, impacts and management of heavy metals
- 10 November 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (11) , 1-27
Open AccessFrom origin to oversight: properties, impacts and management of heavy metals
- 16 May 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1012, 67-78
A Review of Corrosion Threat in Marine Industry
Corrosion poses a significant challenge in the marine industry, leading to the deterioration of equipment and structures, and resulting in substantial costs for its management and control. This comprehensive review focuses on how metal structures in marine environments, such as ships, are affected by corrosion. It explores different forms of corrosion and strategies to prevent it, particularly in the context of marine vessels. The review includes real-world examples of ships, highlights the financial impact of corrosion in the marine sector, and examines the factors contributing to its occurrence. Corrosion prevents a significant issue for marine vessels and related equipment due to the potential damage to the metal they constructed form. However, there are effective methods to mitigate this problem, such as employing corrosion-inhibiting substances and selecting appropriate materials. The susceptibility of materials to corrosion varies depending on their composition, resulting in either widespread deterioration or localized damages. By thoroughly examining the corrosion challenge within the maritime industry, this review provides insights into managing and mitigating its effects more efficiently.
- 16 May 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1012, 67-78
A Review of Corrosion Threat in Marine Industry
Corrosion poses a significant challenge in the marine industry, leading to the deterioration of equipment and structures, and resulting in substantial costs for its management and control. This comprehensive review focuses on how metal structures in marine environments, such as ships, are affected by corrosion. It explores different forms of corrosion and strategies to prevent it, particularly in the context of marine vessels. The review includes real-world examples of ships, highlights the financial impact of corrosion in the marine sector, and examines the factors contributing to its occurrence. Corrosion prevents a significant issue for marine vessels and related equipment due to the potential damage to the metal they constructed form. However, there are effective methods to mitigate this problem, such as employing corrosion-inhibiting substances and selecting appropriate materials. The susceptibility of materials to corrosion varies depending on their composition, resulting in either widespread deterioration or localized damages. By thoroughly examining the corrosion challenge within the maritime industry, this review provides insights into managing and mitigating its effects more efficiently.
- 15 May 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1148, 3-14
Production of Activated Carbon from Cow and Goat Bones for the Treatment of Distillery Wastewater
The use of activated carbon for waste water treatment has been established based on sustainability and cost. This study delves into the intricate process of producing activated carbon from cow and goat bones and explores the efficiency of this material in removing contaminants from distillery wastewater. The samples were carbonized at 700°C in a muffle furnace, then crushed in a mortar after cooling. The crushed samples were activated using 0.4M phosphoric acid for 24 hours and washed with distilled water, and finally oven dried. The elemental and microstructural was carried on the prepared activated carbon (AC) samples using X-ray Fluorescence (XRF) and Scanning Electron Microscopy (SEM). The heavy metals in the treated water were tested using Atomic Absorption Spectroscopy (AAS). The AC was used to treat waste water and factors on which adsorption depend, such as contact time (35 minutes and 60 minutes), adsorbent dosage (2.5g and 5g), and initial contaminant concentration (100% and 50%) were varied for each activated carbon sample (cow bone AC, goat bone AC, and a mixture of equal ratios of both). It was reported that activated carbon prepared from animal bones is rich in calcium. Also, chemical activation with phosphoric acid led to an increase in the external surface area of the particles with irregular cavities and pores. AC prepared from the mixture of cow and goat bones was most effective for distillery wastewater purification.
- 15 May 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1148, 3-14
Production of Activated Carbon from Cow and Goat Bones for the Treatment of Distillery Wastewater
The use of activated carbon for waste water treatment has been established based on sustainability and cost. This study delves into the intricate process of producing activated carbon from cow and goat bones and explores the efficiency of this material in removing contaminants from distillery wastewater. The samples were carbonized at 700°C in a muffle furnace, then crushed in a mortar after cooling. The crushed samples were activated using 0.4M phosphoric acid for 24 hours and washed with distilled water, and finally oven dried. The elemental and microstructural was carried on the prepared activated carbon (AC) samples using X-ray Fluorescence (XRF) and Scanning Electron Microscopy (SEM). The heavy metals in the treated water were tested using Atomic Absorption Spectroscopy (AAS). The AC was used to treat waste water and factors on which adsorption depend, such as contact time (35 minutes and 60 minutes), adsorbent dosage (2.5g and 5g), and initial contaminant concentration (100% and 50%) were varied for each activated carbon sample (cow bone AC, goat bone AC, and a mixture of equal ratios of both). It was reported that activated carbon prepared from animal bones is rich in calcium. Also, chemical activation with phosphoric acid led to an increase in the external surface area of the particles with irregular cavities and pores. AC prepared from the mixture of cow and goat bones was most effective for distillery wastewater purification.
- Top Cited PapersOpen Access
Review on the impact of heavy metals from industrial wastewater effluent and removal technologies
Top Cited PapersOpen AccessReview on the impact of heavy metals from industrial wastewater effluent and removal technologies
- Open Access
- 18 December 2023
- Published by MDPI AG in Preprints.org
Adsorption of Heavy Metals from Paint Industry Wastewater Using Activated African Cherry Seed Shell and Brewers Spent Grain
The disposal of heavy metals from industrial wastewater, especially in the paint industry, poses a significant environmental. Activated carbon is already known to play significant roles in removal of heavy metals from waste water. However, inefficiency of activated carbon in heavy metal adsorption has been traced to the inherit chemical properties in the biomass sources. It is proposed in this study that biomass source will have significant effect on its specific surfaces, pore volumes, and pore size distributions. African Cherry Seed Shell (CSS) and brewer's spent grain (BSG) was used in this experimentation. The prepared Activated carbon was carbonized at 5500C before it was activated chemically using phosphoric acid at an impregnation ratio of 1:2.5, 1:5, 1:10. The prepared activated carbon was used to treat the wastewater via batch adsorption for a contact time of 60 minutes and 120 minutes. The batch adsorption efficiency was studied by varying contact time, impregnation ratio which in turn varied surface area. The ion concentration, surface morphology, surface area and pore size, surface active functional group were characterized using Atomic Absorption Spectrometry (AAS), Scanning Electron Microscopy (SEM) analysis, Brunauer-Emmett-Teller (BET) analysis and Fourier Transform Infrared Spectroscopy (FTIR) respectively. It was concluded from the results that both adsorbents are good potential precursors in removal of heavy metals. However, the brewery spent grain was found to be more effective in the removal of lead, copper and chromium as it gave better efficiencies.
- 18 December 2023
- Published by MDPI AG in Preprints.org
Open AccessAdsorption of Heavy Metals from Paint Industry Wastewater Using Activated African Cherry Seed Shell and Brewers Spent Grain
The disposal of heavy metals from industrial wastewater, especially in the paint industry, poses a significant environmental. Activated carbon is already known to play significant roles in removal of heavy metals from waste water. However, inefficiency of activated carbon in heavy metal adsorption has been traced to the inherit chemical properties in the biomass sources. It is proposed in this study that biomass source will have significant effect on its specific surfaces, pore volumes, and pore size distributions. African Cherry Seed Shell (CSS) and brewer's spent grain (BSG) was used in this experimentation. The prepared Activated carbon was carbonized at 5500C before it was activated chemically using phosphoric acid at an impregnation ratio of 1:2.5, 1:5, 1:10. The prepared activated carbon was used to treat the wastewater via batch adsorption for a contact time of 60 minutes and 120 minutes. The batch adsorption efficiency was studied by varying contact time, impregnation ratio which in turn varied surface area. The ion concentration, surface morphology, surface area and pore size, surface active functional group were characterized using Atomic Absorption Spectrometry (AAS), Scanning Electron Microscopy (SEM) analysis, Brunauer-Emmett-Teller (BET) analysis and Fourier Transform Infrared Spectroscopy (FTIR) respectively. It was concluded from the results that both adsorbents are good potential precursors in removal of heavy metals. However, the brewery spent grain was found to be more effective in the removal of lead, copper and chromium as it gave better efficiencies.
- 4 May 2022
- Published by Springer Nature
- p. 335-353
Gasific: A Python Tool for Biomass Gasification Process
- 4 May 2022
- Published by Springer Nature
- p. 335-353
Gasific: A Python Tool for Biomass Gasification Process
- Open Access
Production of activated carbon from sawdust and its efficiency in the treatment of sewage water
- Open Access
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 168-171
Outdoor Air Pollution in Kumbo Cameroun
In this paper, the air quality of Kumbo-Cameroon was investigated. Aerosol optical depth (AOD) dataset for fourteen years was obtained from the Multi-angle Imaging Spectro-Radiometer (MISR). The raw dataset was processed and treated. The aerosol loading over the research location was obtained from the AOD datasets. It was observed that the main pollution is from anthropogenic emission and Sahara dust. The current aerosol loading over Kumbo is high and it is gradually reducing by 1.81%, though not significantly. The data presented is essential for ground measurement over the research area.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 168-171
Open AccessOutdoor Air Pollution in Kumbo Cameroun
In this paper, the air quality of Kumbo-Cameroon was investigated. Aerosol optical depth (AOD) dataset for fourteen years was obtained from the Multi-angle Imaging Spectro-Radiometer (MISR). The raw dataset was processed and treated. The aerosol loading over the research location was obtained from the AOD datasets. It was observed that the main pollution is from anthropogenic emission and Sahara dust. The current aerosol loading over Kumbo is high and it is gradually reducing by 1.81%, though not significantly. The data presented is essential for ground measurement over the research area.