Matheus Paes Paschoalino
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Matheus Paes Paschoalino has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Fernando Manetti Bronca Mesquita2 shared publications
- Wilson de Figueiredo Jardim
Universidade Estadual de Campinas, Campinas, Brasil
2 shared publications Antonio Alberto da Silva Alfaya
Universidade Estadual de Londrina, Londrina, Brasil
1 shared publication- Brandon E. L. Morris
Department of Microbiology and Plant Biology, University of Oklahoma, Norman, Oklahoma, USA
1 shared publication - Bruna Onuki1 shared publication
Bruno Costa Mundim
1 shared publication
Latest Publications
- 1 December 2020
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 20 (2020) , 55-56
MIC mitigation in oilfields with produced water reinjection through a combination of biocides
- 1 December 2020
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 20 (2020) , 55-56
MIC mitigation in oilfields with produced water reinjection through a combination of biocides
- 1 December 2020
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 20 (2020) , 188-189
Advanced diagnostic of microbial contamination on water injection systems in six brazillian FPSO
- 1 December 2020
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 20 (2020) , 188-189
Advanced diagnostic of microbial contamination on water injection systems in six brazillian FPSO
- 26 March 2017
- Published by Association for Materials Protection and Performance (AMPP)
- p. 1-15
A Case Study for MIC Evaluation and Mitigation in Two Argentinian Oilfields
Microbially Influenced Corrosion (MIC) was suspected to be the root cause of corrosion problems in Pan American Energy (PAE) oilfields in the San Jorge Gulf area. An integrated and innovative program was proposed to address the MIC issues encountered. It consisted of microbial field audits with advanced diagnostics analyses (investigate), and biocide evaluations under field conditions (remediate). A combination of qPCR and next generation sequencing analyses performed indicated an increasing abundance of Bacteria and Archaea, when moving from production wells to oil storage tanks, and strongly suggested that microorganisms played a major role in the corrosion failures. Consequently, a biocide efficacy study was conducted using field water samples and associated indigenous microorganisms as the test inocula. Thirteen biocide systems, including non-traditional products for the oil and gas market, at three different concentrations were evaluated to determine an excellent choice for disinfecting (rapid kill), to alleviate initial bio-burden, along with a longer term protection for the down-hole reservoir. Two formulations, PAE–A (Glutaraldehyde + THNM)) and PAE-E (THPS + THNM) were found to be the most effective and met the criteria of both rapid kill and long term protection in the lab. The microbial solution PAE-E is now in the process of being validated in a three month field trial.
- 26 March 2017
- Published by Association for Materials Protection and Performance (AMPP)
- p. 1-15
A Case Study for MIC Evaluation and Mitigation in Two Argentinian Oilfields
Microbially Influenced Corrosion (MIC) was suspected to be the root cause of corrosion problems in Pan American Energy (PAE) oilfields in the San Jorge Gulf area. An integrated and innovative program was proposed to address the MIC issues encountered. It consisted of microbial field audits with advanced diagnostics analyses (investigate), and biocide evaluations under field conditions (remediate). A combination of qPCR and next generation sequencing analyses performed indicated an increasing abundance of Bacteria and Archaea, when moving from production wells to oil storage tanks, and strongly suggested that microorganisms played a major role in the corrosion failures. Consequently, a biocide efficacy study was conducted using field water samples and associated indigenous microorganisms as the test inocula. Thirteen biocide systems, including non-traditional products for the oil and gas market, at three different concentrations were evaluated to determine an excellent choice for disinfecting (rapid kill), to alleviate initial bio-burden, along with a longer term protection for the down-hole reservoir. Two formulations, PAE–A (Glutaraldehyde + THNM)) and PAE-E (THPS + THNM) were found to be the most effective and met the criteria of both rapid kill and long term protection in the lab. The microbial solution PAE-E is now in the process of being validated in a three month field trial.
- Open Access
- 1 January 2010
- Published by FapUNIFESP (SciELO) in Química Nova
- Vol. 33 (2) , 421-430
Os nanomateriais e a questão ambiental
The increasing use of nanomaterials in several products in different areas such as electronics, cosmetics, food and drugs has attracted the attention of the scientific community due to unknown properties of these materials, such as the life cycle and the interaction with receptor organisms once they reach the environment. In this context, the present work shows an updated scenario of nanomaterials applications, characterization methods and toxicity evaluation, also addressing important aspects related to the development and application of nanotechnology under the environmental point of view.
- 1 January 2010
- Published by FapUNIFESP (SciELO) in Química Nova
- Vol. 33 (2) , 421-430
Open AccessOs nanomateriais e a questão ambiental
The increasing use of nanomaterials in several products in different areas such as electronics, cosmetics, food and drugs has attracted the attention of the scientific community due to unknown properties of these materials, such as the life cycle and the interaction with receptor organisms once they reach the environment. In this context, the present work shows an updated scenario of nanomaterials applications, characterization methods and toxicity evaluation, also addressing important aspects related to the development and application of nanotechnology under the environmental point of view.
- 1 January 2009
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 113 (1) , 395-400
Silicone rubbers filled with TiO2: Characterization and photocatalytic activity
- 1 January 2009
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 113 (1) , 395-400
Silicone rubbers filled with TiO2: Characterization and photocatalytic activity
- 1 December 2008
- Published by Hindawi Limited in Indoor Air
- Vol. 18 (6) , 473-479
Indoor air disinfection using a polyester supported TiO2photo-reactor
Among the decontamination methods applicable to indoor air, heterogeneous photocatalysis has received increasing attention in recent years. This decontamination method is based on the UV irradiation of a solid catalyst, normally TiO2, aiming at the generation of highly reactive hydroxyl radicals. In this work, a novel way to prepare the photocatalyst was used, incorporating pure P-25 TiO2 (Degussa) into polyester orthophthalic polymer. The film was coated onto the walls of a PVC reactor with a concentric 30 W germicidal lamp (254 nm). The efficiency of this prototype was evaluated against fungi and bacteria elimination in a 67 m3 confined room. The system was very efficient for bacteria reduction, decreasing the bacterial count to below the detection limit (1 CFU/plate during 30-min sampling) after 2 h of operation at 195 l/min. For fungi, the gas-phase reactor showed to be less efficient and silver doping of the catalyst showed no increase in biocide activity. The use of a photocatalytic reactor based on TiO2 incorporated onto polyester orthophtalic polymer has been tested at 195 l/min, showing good performance in the air disinfection of a 67 m3 room.
- 1 December 2008
- Published by Hindawi Limited in Indoor Air
- Vol. 18 (6) , 473-479
Indoor air disinfection using a polyester supported TiO2photo-reactor
Among the decontamination methods applicable to indoor air, heterogeneous photocatalysis has received increasing attention in recent years. This decontamination method is based on the UV irradiation of a solid catalyst, normally TiO2, aiming at the generation of highly reactive hydroxyl radicals. In this work, a novel way to prepare the photocatalyst was used, incorporating pure P-25 TiO2 (Degussa) into polyester orthophthalic polymer. The film was coated onto the walls of a PVC reactor with a concentric 30 W germicidal lamp (254 nm). The efficiency of this prototype was evaluated against fungi and bacteria elimination in a 67 m3 confined room. The system was very efficient for bacteria reduction, decreasing the bacterial count to below the detection limit (1 CFU/plate during 30-min sampling) after 2 h of operation at 195 l/min. For fungi, the gas-phase reactor showed to be less efficient and silver doping of the catalyst showed no increase in biocide activity. The use of a photocatalytic reactor based on TiO2 incorporated onto polyester orthophtalic polymer has been tested at 195 l/min, showing good performance in the air disinfection of a 67 m3 room.
- 1 September 2008
- Published by Elsevier in Journal of Photochemistry and Photobiology A: Chemistry
- Vol. 199 (1) , 105-111
Inactivation of E. coli mediated by high surface area CuO accelerated by light irradiation >360 nm
- 1 September 2008
- Published by Elsevier in Journal of Photochemistry and Photobiology A: Chemistry
- Vol. 199 (1) , 105-111
Inactivation of E. coli mediated by high surface area CuO accelerated by light irradiation >360 nm
- 13 September 2007
- Published by SPIE-Intl Soc Optical Eng
- p. 66500T-66500T-9
Photoelectrochemical and photocatalytic properties of nanocrystalline TiO 2 electrodes
The electrochemical and photocatalytic properties of a TiO2 film deposited on transparent electrodes were investigated. Its electrochemical behavior was typical of an n-type semiconductor electrode. Its photocatalytic activity, investigated for phenol degradation on an optical bench (area of 1 cm2, 5 mL of solution), revealed small currents (3 μA) and poor total organic carbon (TOC) removal (5 %) when the electrode was biased at + 1.1 V in the dark for 3 h. Under polychromatic irradiation, the electrode presented 25 μA of current and 12 % of phenol degradation. A better performance was achieved for photoelectrocatalytic configuration, when the electrode was irradiated and biased with + 0.6 V. Experiments done under irradiation with a metallic vapor lamp using 9 cm2 electrodes and 10 mL of solution revealed that heterogeneous photocatalysis configuration (HPC) resulted in 50 % of TOC removal, while 85 % was achieved by the electro-assisted process (EHPC). Both the configurations exhibited pseudo-first order kinetics for phenol degradation, but the rate constant was two times that of EHPC. The application of a potential bias to the TiO2 porous electrode must enhance the photogenerated electron/hole separation, which minimize the charge recombination and increases its photocatalytic activity towards organic pollutant degradation.
- 13 September 2007
- Published by SPIE-Intl Soc Optical Eng
- p. 66500T-66500T-9
Photoelectrochemical and photocatalytic properties of nanocrystalline TiO 2 electrodes
The electrochemical and photocatalytic properties of a TiO2 film deposited on transparent electrodes were investigated. Its electrochemical behavior was typical of an n-type semiconductor electrode. Its photocatalytic activity, investigated for phenol degradation on an optical bench (area of 1 cm2, 5 mL of solution), revealed small currents (3 μA) and poor total organic carbon (TOC) removal (5 %) when the electrode was biased at + 1.1 V in the dark for 3 h. Under polychromatic irradiation, the electrode presented 25 μA of current and 12 % of phenol degradation. A better performance was achieved for photoelectrocatalytic configuration, when the electrode was irradiated and biased with + 0.6 V. Experiments done under irradiation with a metallic vapor lamp using 9 cm2 electrodes and 10 mL of solution revealed that heterogeneous photocatalysis configuration (HPC) resulted in 50 % of TOC removal, while 85 % was achieved by the electro-assisted process (EHPC). Both the configurations exhibited pseudo-first order kinetics for phenol degradation, but the rate constant was two times that of EHPC. The application of a potential bias to the TiO2 porous electrode must enhance the photogenerated electron/hole separation, which minimize the charge recombination and increases its photocatalytic activity towards organic pollutant degradation.
- 26 October 2006
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 68 (1-2) , 68-73
Gas-phase photocatalytic decontamination using polymer supported TiO2
- 26 October 2006
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 68 (1-2) , 68-73
Gas-phase photocatalytic decontamination using polymer supported TiO2
- Open Access
- 1 July 2006
- Published by FapUNIFESP (SciELO) in Química Nova
- Vol. 29 (4) , 699-703
Incorporação de CuSO4 residual em argamassa, como método de disposição final
Residual CuSO4 was incorporated into the mass utilized for cement preparation. To a cement mass with 1:0.5:5 of cement, lime and sand to 0.25, 0.50, 0.75 and 1.00% of residual CuSO4 were added. The sulfate was mixed separately with lime and water to induce metal precipitation. The hardened test bodies were submerged in Milli-Q water for three months. No Cu was detected in the water by Atomic Absorption Spectrometry. The best proportion for mechanical resistance and porosity is 0.50%. The cement is adequate for non-structural objects
- 1 July 2006
- Published by FapUNIFESP (SciELO) in Química Nova
- Vol. 29 (4) , 699-703
Open AccessIncorporação de CuSO4 residual em argamassa, como método de disposição final
Residual CuSO4 was incorporated into the mass utilized for cement preparation. To a cement mass with 1:0.5:5 of cement, lime and sand to 0.25, 0.50, 0.75 and 1.00% of residual CuSO4 were added. The sulfate was mixed separately with lime and water to induce metal precipitation. The hardened test bodies were submerged in Milli-Q water for three months. No Cu was detected in the water by Atomic Absorption Spectrometry. The best proportion for mechanical resistance and porosity is 0.50%. The cement is adequate for non-structural objects