Leonildes Soares De Melo Filho
Leonildes Soares De Melo Filho has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Antônio Rosales Gonçalves Oliveira
Institute of Petroleum and Natural Resources (IPR), Pontifical Catholic University of Rio Grande do Sul (PUC-RS), Porto Alegre 90619-900, Brazil
4 shared publications - Breno Leitão Waichel
UFSC
4 shared publications - Cassiane Maria Ferreira Nunes
Repsol Sinopec Brasil
4 shared publications - Felipe Dalla Vecchia
Institute of Petroleum and Natural Resources (IPR), Pontifical Catholic University of Rio Grande do Sul (PUCRS), Avenida Ipiranga, 6681, Porto Alegre, RS, Brazil
4 shared publications - João Pedro Tauscheck Zielinski
Institute of Petroleum and Natural Resources (IPR), Pontifical Catholic University of Rio Grande do Sul (PUCRS), Porto Alegre 90619-900, RS, Brazil
4 shared publications - Pedro Costabile de Souza
UFRGS
4 shared publications
Latest Publications
- Open Access
- 10 March 2026
- Published by Sociedade Brasileira de Geofisica in Brazilian Journal of Geophysics
- Vol. 44 (1) , e2355
Time-Lapse Seismic Modeling from Reservoir Simulation Models: an Evaluation of Non-Reservoir Cell Filling and Noise Addition
Seismic forward modeling constitutes an essential tool in 4D seismic investigations, enabling the accurate prediction of subsurface seismic responses. This procedure plays a critical role in the improvement and validation of reservoir models by simulating seismic attributes under diverse geological and fluid conditions. The first component of this methodology is the implementation of a petroelastic model (PEM), which translates reservoir simulation outputs into elastic properties, including P- and S-impedances. A convolutional model is then applied to these properties and the synthetic amplitudes are calculated, which can be compared with measured data. To ensure accurate comparisons, apart from using appropriate methods for the predictions at the reservoir level, one must define the elastic properties at the overburden and underburden intervals, in which flow simulation results are normally not available. This study evaluates three 4D seismic forward modeling approaches applied to simulation models. Two are derived from a traditional petroelastic model, whereas the third integrates a petroelastic–inversion workflow. To improve the match with observed seismic data, the strategies evaluated consist of: i) forward modeling using a constant value of acoustic impedance in the overburden and underburden (FMCOU); ii) forward modeling using inversion results to define the overburden and underburden (FMIOU); and iii) forward modeling derived from a combination of petroelastic results and seismic inversion data (FMFI). Our findings indicate that the 3D results obtained from FMIOU and FMFI cases better align with the real seismic, but in the 4D analysis, the different approaches present similar behaviors. The modeled 4D amplitudes from FMCOU and FMIOU are identical and very similar to FMFI, and all show a fair match with the real seismic. Within this context, the use of the less complex approach (FMCOU) proved a suitable choice for 4D seismic studies.
- 10 March 2026
- Published by Sociedade Brasileira de Geofisica in Brazilian Journal of Geophysics
- Vol. 44 (1) , e2355
Open AccessTime-Lapse Seismic Modeling from Reservoir Simulation Models: an Evaluation of Non-Reservoir Cell Filling and Noise Addition
Seismic forward modeling constitutes an essential tool in 4D seismic investigations, enabling the accurate prediction of subsurface seismic responses. This procedure plays a critical role in the improvement and validation of reservoir models by simulating seismic attributes under diverse geological and fluid conditions. The first component of this methodology is the implementation of a petroelastic model (PEM), which translates reservoir simulation outputs into elastic properties, including P- and S-impedances. A convolutional model is then applied to these properties and the synthetic amplitudes are calculated, which can be compared with measured data. To ensure accurate comparisons, apart from using appropriate methods for the predictions at the reservoir level, one must define the elastic properties at the overburden and underburden intervals, in which flow simulation results are normally not available. This study evaluates three 4D seismic forward modeling approaches applied to simulation models. Two are derived from a traditional petroelastic model, whereas the third integrates a petroelastic–inversion workflow. To improve the match with observed seismic data, the strategies evaluated consist of: i) forward modeling using a constant value of acoustic impedance in the overburden and underburden (FMCOU); ii) forward modeling using inversion results to define the overburden and underburden (FMIOU); and iii) forward modeling derived from a combination of petroelastic results and seismic inversion data (FMFI). Our findings indicate that the 3D results obtained from FMIOU and FMFI cases better align with the real seismic, but in the 4D analysis, the different approaches present similar behaviors. The modeled 4D amplitudes from FMCOU and FMIOU are identical and very similar to FMFI, and all show a fair match with the real seismic. Within this context, the use of the less complex approach (FMCOU) proved a suitable choice for 4D seismic studies.
- Open Access
- 17 July 2025
- Published by Universidade Federal do Parana in Boletim Paranaense de Geociências
- Vol. 83 (2) , 1-10
Classifying the reactivity of volcanic rocks from the Serra Geral Group: an approach using a proposed Reactivity Index (RI)
The increasing global interest in CO₂ mineralization in basaltic rocks has led to studies within Large Igneous Provinces (LIPs), particularly focusing on their carbon storage potential. In South America, the Serra Geral Group (SGG), part of the Paraná-Etendeka Province, has been the subject of investigations due to its compositional diversity and extensive volcanic sequences. This study assesses the applicability of the Reactivity Index (RI) as a predictive tool for geochemical reactivity in six SGG volcanic rock samples, compared with two Icelandic basalts and one Columbia River Basalt (CRB). Results reveal RI values for SGG samples ranging from -11.1 to -6.7 log mol/s, aligning well with the observations from batch reactor experiments. Higher RI values were associated with increased reactivity, supporting the use of the index as a reliable proxy, especially in preliminary evaluations, although it does not account for textural characteristics or surface area variations. The samples from SGG, Icelandic, and CRB showed similar RI values. When integrated with petrography, surface area, and chemical data, the RI provides a promising tool for evaluating the reactivity of volcanic rocks in carbon storage strategies.
- 17 July 2025
- Published by Universidade Federal do Parana in Boletim Paranaense de Geociências
- Vol. 83 (2) , 1-10
Open AccessClassifying the reactivity of volcanic rocks from the Serra Geral Group: an approach using a proposed Reactivity Index (RI)
The increasing global interest in CO₂ mineralization in basaltic rocks has led to studies within Large Igneous Provinces (LIPs), particularly focusing on their carbon storage potential. In South America, the Serra Geral Group (SGG), part of the Paraná-Etendeka Province, has been the subject of investigations due to its compositional diversity and extensive volcanic sequences. This study assesses the applicability of the Reactivity Index (RI) as a predictive tool for geochemical reactivity in six SGG volcanic rock samples, compared with two Icelandic basalts and one Columbia River Basalt (CRB). Results reveal RI values for SGG samples ranging from -11.1 to -6.7 log mol/s, aligning well with the observations from batch reactor experiments. Higher RI values were associated with increased reactivity, supporting the use of the index as a reliable proxy, especially in preliminary evaluations, although it does not account for textural characteristics or surface area variations. The samples from SGG, Icelandic, and CRB showed similar RI values. When integrated with petrography, surface area, and chemical data, the RI provides a promising tool for evaluating the reactivity of volcanic rocks in carbon storage strategies.
- Open Access
- 17 July 2025
- Published by Universidade Federal do Parana in Boletim Paranaense de Geociências
- Vol. 83 (2) , 1-8
IDENTIFICATION OF POTENTIAL CO2 INJECTION ZONES IN THE SERRA GERAL GROUP: A GEOPHYSICAL ANALYSIS OF LEGACY DRILLED WELLS
Os basaltos do Grupo Serra Geral (GSG), na Bacia do Paraná, têm despertado interesse devido ao seu potencial para mineralização de CO2. Apesar de sua ampla extensão (~787.000 km²), dados geológicos são limitados, dificultando a identificação de zonas de armazenamento. Este estudo propõe um fluxo de trabalho integrado baseado na interpretação de perfis geofísicos de quatro poços (1-PT-1-PR, 2-AN-1-PR, 1-API-1-PR e 1-AV-1-PR) situados em uma área com potencial para armazenamento geológico de CO2. O poço 1-PT-1-PR foi usado como modelo de referência e revelou padrões distintos de interiores de fluxo e horizontes entre os fluxos. A porosidade foi estimada utilizando uma relação entre velocidade e porosidade baseada nas velocidades da onda P. Foram identificadas zonas de alta porosidade (Φ >10%), associadas a topos ou bases de derrames e derrames compostos. Intervalos de alta porosidade apresentaram valores de densidade reduzida (~2 g/cm³), porosidade até 30% e velocidades de onda P baixas (~3,1 km/s). Nos demais poços, também foram identificados múltiplos intervalos de alta porosidade, com “net-to-gross” variando entre 19% e 43%. Picos de raios gama, excursões positivas no perfil de caliper e valores reduzidos de resistividade sustentam a presença de zonas porosas e alteradas. Os resultados indicam a recorrência e possível continuidade lateral desses intervalos, reforçando sua viabilidade como reservatórios. O método aplicado contribui para delimitar zonas potenciais para futura injeção de CO2 no GSG. Trabalhos futuros serão direcionados à correlação sub-regional, com o objetivo de embasar projetos de mineralização voltados a áreas específicas.
- 17 July 2025
- Published by Universidade Federal do Parana in Boletim Paranaense de Geociências
- Vol. 83 (2) , 1-8
Open AccessIDENTIFICATION OF POTENTIAL CO2 INJECTION ZONES IN THE SERRA GERAL GROUP: A GEOPHYSICAL ANALYSIS OF LEGACY DRILLED WELLS
Os basaltos do Grupo Serra Geral (GSG), na Bacia do Paraná, têm despertado interesse devido ao seu potencial para mineralização de CO2. Apesar de sua ampla extensão (~787.000 km²), dados geológicos são limitados, dificultando a identificação de zonas de armazenamento. Este estudo propõe um fluxo de trabalho integrado baseado na interpretação de perfis geofísicos de quatro poços (1-PT-1-PR, 2-AN-1-PR, 1-API-1-PR e 1-AV-1-PR) situados em uma área com potencial para armazenamento geológico de CO2. O poço 1-PT-1-PR foi usado como modelo de referência e revelou padrões distintos de interiores de fluxo e horizontes entre os fluxos. A porosidade foi estimada utilizando uma relação entre velocidade e porosidade baseada nas velocidades da onda P. Foram identificadas zonas de alta porosidade (Φ >10%), associadas a topos ou bases de derrames e derrames compostos. Intervalos de alta porosidade apresentaram valores de densidade reduzida (~2 g/cm³), porosidade até 30% e velocidades de onda P baixas (~3,1 km/s). Nos demais poços, também foram identificados múltiplos intervalos de alta porosidade, com “net-to-gross” variando entre 19% e 43%. Picos de raios gama, excursões positivas no perfil de caliper e valores reduzidos de resistividade sustentam a presença de zonas porosas e alteradas. Os resultados indicam a recorrência e possível continuidade lateral desses intervalos, reforçando sua viabilidade como reservatórios. O método aplicado contribui para delimitar zonas potenciais para futura injeção de CO2 no GSG. Trabalhos futuros serão direcionados à correlação sub-regional, com o objetivo de embasar projetos de mineralização voltados a áreas específicas.
- Open Access
- 17 July 2025
- Published by Universidade Federal do Parana in Boletim Paranaense de Geociências
- Vol. 83 (2) , 1-9
UNDERGROUND CO₂ MINERALIZATION POTENTIAL IN PARANÁ STATE: PRELIMINARY ASSESSMENT OF BASALTIC ROCKS FROM SERRA GERAL GROUP
The Paraná Basin's CO2 geological storage potential is significant due to its coal deposits, saline formations, CO2 emission sources, and pipeline network. Recent interest has shifted to volcanic rocks containing divalent cations, facilitating mineral carbonation. The basin's volcanic rocks have an estimated CO2 storage capacity of 2,840 Gt and areas of ca. 174,000 km2 in total were identified in different parts of Brazil. Paraná State, with its vast geological data, is ideal for a detailed assessment, especially in the Serra Geral Group (SGG), which covers over half of the state. Using different methodologies, the CO2 storage capacity in this area was estimated between 79 to 654 Gt, with further research required for precise quantification and the identification of possible reservoirs for CO2 injection.
- 17 July 2025
- Published by Universidade Federal do Parana in Boletim Paranaense de Geociências
- Vol. 83 (2) , 1-9
Open AccessUNDERGROUND CO₂ MINERALIZATION POTENTIAL IN PARANÁ STATE: PRELIMINARY ASSESSMENT OF BASALTIC ROCKS FROM SERRA GERAL GROUP
The Paraná Basin's CO2 geological storage potential is significant due to its coal deposits, saline formations, CO2 emission sources, and pipeline network. Recent interest has shifted to volcanic rocks containing divalent cations, facilitating mineral carbonation. The basin's volcanic rocks have an estimated CO2 storage capacity of 2,840 Gt and areas of ca. 174,000 km2 in total were identified in different parts of Brazil. Paraná State, with its vast geological data, is ideal for a detailed assessment, especially in the Serra Geral Group (SGG), which covers over half of the state. Using different methodologies, the CO2 storage capacity in this area was estimated between 79 to 654 Gt, with further research required for precise quantification and the identification of possible reservoirs for CO2 injection.
- Open Access
- 17 July 2025
- Published by Universidade Federal do Parana in Boletim Paranaense de Geociências
- Vol. 83 (2) , 1-6
STUDY OF CHEMICAL REACTIVITY FOR CO2 MINERALIZATION POTENTIAL IN VOLCANIC ROCK PLUGS FROM THE SERRA GERAL GROUP
This study investigates the potential of basalts from the Serra Geral Group for geological CO2 storage, focusing on the geochemical behavior of the rocks under reservoir-like conditions at a depth of 900 m. Massive and brecciated basalt samples were characterized in terms of porosity, permeability, and petrography. Closed-system reactor experiments will be conducted at 50 bar and 40 °C for 24 weeks to simulate fluid-rock interactions. Post-experimental analyses will include SEM-EDS, X-ray microtomography, petrographic descriptions to assess mineralogical alterations, and for the fluid; analysis of pH, electrical conductivity, total alkalinity, and chemical composition (ICP-MS and IC). The goal is to evaluate basalt reactivity and its potential for carbonate mineralization and long-term CO2 sequestration.
- 17 July 2025
- Published by Universidade Federal do Parana in Boletim Paranaense de Geociências
- Vol. 83 (2) , 1-6
Open AccessSTUDY OF CHEMICAL REACTIVITY FOR CO2 MINERALIZATION POTENTIAL IN VOLCANIC ROCK PLUGS FROM THE SERRA GERAL GROUP
This study investigates the potential of basalts from the Serra Geral Group for geological CO2 storage, focusing on the geochemical behavior of the rocks under reservoir-like conditions at a depth of 900 m. Massive and brecciated basalt samples were characterized in terms of porosity, permeability, and petrography. Closed-system reactor experiments will be conducted at 50 bar and 40 °C for 24 weeks to simulate fluid-rock interactions. Post-experimental analyses will include SEM-EDS, X-ray microtomography, petrographic descriptions to assess mineralogical alterations, and for the fluid; analysis of pH, electrical conductivity, total alkalinity, and chemical composition (ICP-MS and IC). The goal is to evaluate basalt reactivity and its potential for carbonate mineralization and long-term CO2 sequestration.
- 26 September 2022
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 22 (2022) , 35-36
Waterflooding optimization with multidimensional output constraints using a modified Net Present Value
- 26 September 2022
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 22 (2022) , 35-36
Waterflooding optimization with multidimensional output constraints using a modified Net Present Value
- 26 September 2022
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 22 (2022) , 36-37
Model aggregation to forecast medium-term reservoir production
- 26 September 2022
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 22 (2022) , 36-37
Model aggregation to forecast medium-term reservoir production
- 1 December 2020
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 20 (2020) , 404-405
Digital twin: a case of unified digital assets in Brazilian reality
- 1 December 2020
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 20 (2020) , 404-405
Digital twin: a case of unified digital assets in Brazilian reality
- 1 December 2020
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 20 (2020) , 405-406
Multivariate anomaly detection in rotating machinery of the oil and gas industry using unsupervised machine learning
- 1 December 2020
- Published by Instituto Brasileiro de Petroleo e Gas in Rio Oil and Gas Expo and Conference
- Vol. 20 (2020) , 405-406
Multivariate anomaly detection in rotating machinery of the oil and gas industry using unsupervised machine learning