AKA. V. Kolomeichenko

A. V. Kolomeichenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


A. V. Kolomeichenko has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Applying Aluminum Oxide and Graphene Powder for Restoring a Plowshare Blade

    by A. L. Semeshin, S. N. Konoshina, A. V. Kolomeychenko

    A technology for restoring plowshare blades with the use of a composite powder made of aluminum oxide and graphene. Defects that occur on the blade of the

  • Increasing the Durability of Road Machinery Parts Using Modified Electrochemical Composites

    by Yu. E. Kisel, A. V. Kolomeichenko, P. E. Kisel

    The effect of high-frequency current treatment on the physical and mechanical properties of iron-boron carbide composite coatings is studied. It is found t

  • Effect of drawing squeezing on mechanical properties of some medium-carbon steels

    by R. E. Alekseev Nizhny Novgorod State Technical University (NNSTU), A.A. Filippov, G.V. Pachurin, N.A. Kuzmin, V.V. Galkin

    В работе изучались изменения прочностных и пластических характеристик среднеуглеродистых нелегированных сталей 30 и 45 в процессе волочения проката со степенями обжатия от 5 до 60%. Получен комплекс механических характеристик исследованных конструкционных сталей после деформационного упрочнения в условиях обозначенных деформаций. Проведена сравнительная оценка каждого этапа деформирования проката при различных степенях обжатия и построены кривые упрочнения при сжатии образцов. Даны рекомендации для изготовления изделий с прочностью ≥600 MПа.

  • Use of powder gas-flame spraying to increase life of working bodies of tillage machines

    by Parakhin Orel State Agrarian University, S.A. Zaytsev, N.V. Titov, A.V. Kolomeychenko, Central Research and Development Automobile and Engine Institute «NAMI»

    В работе рассматривается использование порошковых композиций экспериментального состава в качестве материала при газопламенном напылении. По результатам проведенных исследований установлены рациональные режимы напыления разработанной порошковой композиции: дистанция напыления составляет 200 мм, размер частиц порошков - 60 мкм, температура оплавления покрытия - 1000 °C. При их использовании прочность сцепления покрытий составляет 224 MПа, микротвердость - 7820 MПа. Износостойкость рабочих органов почвообрабатывающих машин, имеющих на режуще-лезвийных поверхностях данные покрытия, увеличивается в среднем в 1,4-1,9 раза в зависимости от типа почв.

  • Development of new polymer composite material for manufacturing of excavator-loader door-lock

    by Moscow Automobile and Road Construction State Technical University (MADI), V.A. Zorin, N.J. Maba

    В статье разработан новый полимерный композитный материал для фиксаторов дверей экскаваторов-погрузчиков, соответствующий современным требованиям машиностроения. Исследование направлено на создание надежных конструкционных материалов с улучшенными механическими свойствами. Проведен анализ существующих материалов и технологий, разработана композиция на основе термопластичных полимеров с армирующими волокнами. Оптимизация конструкции фиксатора выполнена с помощью 3D-моделирования и метода конечных элементов. Испытания показали высокую прочность и стойкость нового композита, что делает его перспективным для интенсивной эксплуатации. Результаты подчеркивают необходимость дальнейшей оптимизации, открывая новые возможности для повышения надежности экскаваторов-погрузчиков.

  • Open Access

    Functional evaluation of tractors of traction class 4.0

    by Timirâzevskaâ Selʹskohozâjstvennaâ Akademiâ, И. В. Грибов, Central Scientific Research Automobile and Automotive Engines Institute – FSUE “NAMI”, А. С. Зенин, А. В. Коломейченко, М. В. Шипов, С. Б. Карякин, Н. В. Перевозчикова

    The optimal choice of purchased equipment based on its functional characteristics is an important task for modern agricultural enterprises. In order to select the optimal tractor model, the cost and types of work performed were compared with three tractors of traction class 4.0: Kirovets K-5, BTZ 254-K, and DEUTZ-FAHR6230 TTV. To determine the differences through the examination, the authors used a methodology of comparing tractor models, taking into account indicators of technological versatility, agrotechnical properties, potential (expected) productivity and cost of performing technological operations. They also determined an indicator of the technological level of tractors. The assessment results showed the applicability of all models for plowing and harvesting operations, as well as for working with mounted combined machines. However, the models were considered unsuitable for inter-row cultivation. As compared with domestic counterparts, the DEUTZ-FAHR6230 TTV can reach higherspeeds and higher performance. However, the technological level of Kirovets K-5 and BTZ 254-K tractors has the same value of 0.72 and surpasses the imported analog DEUTZ-FAHR6230 TTV, which has an indicator of 0.69. Taking into account the functional characteristics and cost of tractors, it is profitable for enterprisesto purchase domestic equipment.


  • Corrosion resistance of ceramic coatings formed by microarc oxidation on aluminium alloy AK4-1

    by N. Yu. Dudareva, A. V. Kolomeichenko, V. B. Deev

    This paper describes a study that looked at the effect of the structure of coatings produced by microarc oxidation (MAO) on wrought aluminium alloy AK4-1 on the corrosion resistance of specimens. Different processing modes were applied that were determined by three factors: the capacity of the unit and the concentration of caustic potash and sodium metasilicate in the electrolyte. The coating thickness, coating porosity and corrosion rate of the specimens were used as output parameters. A complete factorial experiment of type 23 was designed and conducted. Images of microsections obtained with a scanning electron microscope were used for studying the coating structure, determined by its porosity and thickness. The porosity was analyzed based on images of the specimens with the help of ImageJ programme. For the corrosion resistance study, the specimens were immersed in a corrosive solution and their corrosion rate was determined. Regression and correlation analyses of the obtained data were carried out in the MS Excel programme. The correlation analysis showed that the corrosion rate strongly depends on the coating thickness. An increase in the coating thickness leads to an increase in the corrosion rate. It is assumed that the coating material does not corrode, and corrosion is the result of the aggressive solution penetrating through cracks to the substrate material, which is what basically corrodes. An increased thickness of the coating is associated with a greater number of cracks in it, which leads to an increased corrosion rate. It was also found that a greater capacity of the unit contributes to the coating thickness on the AK4-1 alloy. Regression equations were also obtained that relate the corrosion rate to the porosity and thickness of the coating, as well as the corrosion rate, porosity and thickness of the coating to the microarc oxidation modes.Support for this research was provided by the Ministry of Science and Higher Education of the Russian Federation under Governmental Assignment No. FEUE-2023-0007 (UUST).

  • Application of Composite Coatings by Vibroarc Carbide Surfacing

    by N. V. Titov, A. V. Kolomeychenko, E. V. Ageev, A. S. Kolomeychenko

    Arc ignition and combustion are investigated in the creation of hard composite coatings by vibroarc carbide surfacing. The electric field strength in vibro


  • Metallurgical Features of Plasma Surfacing with Powder Hard Alloy with Addition of Aluminum Powder

    by I. N. Kravchenko, S. V. Kartsev, А. V. Kolomeichenko, Yu. А. Kuznetsov, S. N. Perevislov, М. А. Markov


  • Open Access

    Evaluation of the wear resistance and resource hardened by electrospark machining of the cutting surfaces of the fingers of the headers of combine harvesters

    by S A Velichko, S N Sharifullin, I S Kuznetsov, A V Kolomeichenko, R Y Solovyev, I N Kravchenko, N R Adigamov

    The article presents the technology of hardening the fingers of the reapers of combine harvesters by electrospark processing. To strengthen the cutting surfaces of the fingers, it is recommended to use an amorphous alloy grade 84KXSR. The operational tests presented in the work showed that wear and dulling of both serial products and experimental parts with electric spark coatings is characterized by two stages: running-in and natural wear. The running-in occurs during the running time of the fingers in 1 ha. The results of operational tests showed that the application of a wear-resistant electrospark coating of amorphous alloy grade 84KXSR with a thickness of 30 μm and a track width of 2 mm on the cutting surfaces of the fingers of the headers of grain harvesters makes it possible to increase the resource from 1.4 to 2 times.