Tom Wettlin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tom Wettlin has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Nebojša Stojanović
Huawei Heisenberg Research Center, Munich, Germany
10 shared publications - Stefano Calabrò
Huawei Heisenberg Research Center, Munich, Germany
10 shared publications - Stephan Pachnicke
Chair of Communications, Kiel University, Kiel, Germany
9 shared publications - Maxim Kuschnerov
Heisenberg Research Center, Huawei Technologies Duesseldorf GmbH, Munich, Germany
4 shared publications - Talha Rahman
Huawei Munich Research Center, Munich, Germany
4 shared publications - Silas Oettinghaus
Chair of Communications, Kiel University, Kiel, Germany
3 shared publications
Latest Publications
- Open Access
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (21) , 1596-1599
FWM Nonlinearity Reduction Techniques for 2 and 10 km 3.2 Tb/s (16 × 200 Gb/s) O-Band IM/DD Systems
In this letter, four-wave mixing (FWM) nonlinearities resulting from wavelength division multiplexing (WDM) propagation near zero dispersion wavelength (ZDW) are studied and mitigation techniques, being polarization interleaving and link segmentation, are systematically analyzed. Link segmentation uses alternating fibers with a slight shift of the ZDW towards shorter and longer wavelengths respectively. 3.2 Tb/s systems, enabled by 16×200 Gb/s 112 GBd PAM-4 signaling with 400 GHz spacing, are simulated for 2 km and 10 km O-band links. The effects of polarization-mode-dispersion on FWM and the tradeoff between nonlinearities and dispersion are studied in detail. Deviations of fiber characteristics and the resulting fluctuations within standard links are taken into consideration. It is shown that link segmentation successfully reduces the FWM penalty to almost zero. The results can be useful for the implementation of next-generation intra data-center networks.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (21) , 1596-1599
Open AccessFWM Nonlinearity Reduction Techniques for 2 and 10 km 3.2 Tb/s (16 × 200 Gb/s) O-Band IM/DD Systems
In this letter, four-wave mixing (FWM) nonlinearities resulting from wavelength division multiplexing (WDM) propagation near zero dispersion wavelength (ZDW) are studied and mitigation techniques, being polarization interleaving and link segmentation, are systematically analyzed. Link segmentation uses alternating fibers with a slight shift of the ZDW towards shorter and longer wavelengths respectively. 3.2 Tb/s systems, enabled by 16×200 Gb/s 112 GBd PAM-4 signaling with 400 GHz spacing, are simulated for 2 km and 10 km O-band links. The effects of polarization-mode-dispersion on FWM and the tradeoff between nonlinearities and dispersion are studied in detail. Deviations of fiber characteristics and the resulting fluctuations within standard links are taken into consideration. It is shown that link segmentation successfully reduces the FWM penalty to almost zero. The results can be useful for the implementation of next-generation intra data-center networks.
- 27 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (14) , 5993-6002
Turbo Equalization for High-Speed Passive Optical Networks
High-speed passive optical networks (PONs) demand advanced digital signal processing (DSP) to achieve higher data rates under stringent bandwidth constraints. In this work, we present an analytical framework to estimate the theoretical turbo equalization (TE) gain for unit-memory channels of the form $1+\alpha D$, applicable to arbitrary inter-symbol interference (ISI) levels $\alpha$ and forward error correction (FEC) code rates. The proposed TE algorithm iteratively exchanges soft information between a log-domain MAP detector and an LDPC decoder based on the standardized (17280,14592) code. Simulation and experimental results for PAM2 and PAM4 signaling confirm significant performance improvements, closely approaching the predicted theoretical gains. We provide a combined theoretical and experimental assessment of TE gains in high-speed optical access networks, offering a practical solution to mitigate ISI and enhance throughput in bandwidth-limited PON receivers.
- 27 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (14) , 5993-6002
Turbo Equalization for High-Speed Passive Optical Networks
High-speed passive optical networks (PONs) demand advanced digital signal processing (DSP) to achieve higher data rates under stringent bandwidth constraints. In this work, we present an analytical framework to estimate the theoretical turbo equalization (TE) gain for unit-memory channels of the form $1+\alpha D$, applicable to arbitrary inter-symbol interference (ISI) levels $\alpha$ and forward error correction (FEC) code rates. The proposed TE algorithm iteratively exchanges soft information between a log-domain MAP detector and an LDPC decoder based on the standardized (17280,14592) code. Simulation and experimental results for PAM2 and PAM4 signaling confirm significant performance improvements, closely approaching the predicted theoretical gains. We provide a combined theoretical and experimental assessment of TE gains in high-speed optical access networks, offering a practical solution to mitigate ISI and enhance throughput in bandwidth-limited PON receivers.
- 23 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (18) , 1247-1250
Turbo Equalization for Flexible PAM-2/4 Passive Optical Networks
We investigate a turbo equalization (TE) scheme combining soft-input soft-output (SISO) Bahl–Cocke–Jelinek–Raviv (BCJR) detection with low-density parity-check (LDPC) decoding based on the standardized (17280, 14592) LDPC code for passive optical networks. For a two-tap intersymbol interference (ISI) channel, the maximal achievable information rates (AIRs) are analytically derived to quantify the performance gap between separate detection and decoding (SDD) and joint detection and decoding (JDD) under different ISI levels. This analysis reveals the potential gain achievable by JDD and motivates the use of TE as a practical approach to approach JDD performance. Experimental results obtained in a 50-GBd pulse-amplitude modulation (PAM) 2/4 passive optical network (PON) system demonstrate that TE provides received optical power (ROP) gains of 0.33 dB for PAM-2 and 0.56 dB for PAM-4, confirming its effectiveness for bandwidth-limited receivers.
- 23 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (18) , 1247-1250
Turbo Equalization for Flexible PAM-2/4 Passive Optical Networks
We investigate a turbo equalization (TE) scheme combining soft-input soft-output (SISO) Bahl–Cocke–Jelinek–Raviv (BCJR) detection with low-density parity-check (LDPC) decoding based on the standardized (17280, 14592) LDPC code for passive optical networks. For a two-tap intersymbol interference (ISI) channel, the maximal achievable information rates (AIRs) are analytically derived to quantify the performance gap between separate detection and decoding (SDD) and joint detection and decoding (JDD) under different ISI levels. This analysis reveals the potential gain achievable by JDD and motivates the use of TE as a practical approach to approach JDD performance. Experimental results obtained in a 50-GBd pulse-amplitude modulation (PAM) 2/4 passive optical network (PON) system demonstrate that TE provides received optical power (ROP) gains of 0.33 dB for PAM-2 and 0.56 dB for PAM-4, confirming its effectiveness for bandwidth-limited receivers.
- Open Access
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. PP (07338724) , 1-11
Advanced Digital Signal Processing for 400 Gb/s/$\lambda$ IM/DD Intra Data Center Systems
This work presents an experimental study of 400 Gb/s/$\lambda$ targeted IM/DD systems in the O-band, which are of high relevance for next-generation 3.2 Tb/s short-reach Ethernet connections inside data centers. For such systems, advanced digital signal processing (DSP) has become essential to overcome bandwidth limitations and accumulated dispersion as dominant channel impairments. On a 2 km link, PAM-4, -6, and -8 as modulation formats, the use of pre-emphasis in the power-constrained transmitter, as well as precoding with the objective to break error bursts are analyzed. At the receiver, four DSP schemes are studied, including (1) full-response Volterra nonlinear equalization, (2) partial-response equalization implemented as Volterra equalization combined with a post-filter for channel shortening and subsequent sequence estimation, (3) duobinary-targeted equalization, combined with sequence estimation for duobinary decoding and (4) a machine-learning-based equalization and sequence estimation architecture. The experimental study is extended to 10 km transmission at wavelengths between 1290-1330 nm to quantify the impact of chromatic dispersion and define permissible wavelength ranges. Optimal DSP architectures are determined, depending on the modulation format and the signaling rate. The results demonstrate achievable information rates of 437 Gb/s for 160 GBd PAM-8, 412 Gb/s for 174 GBd PAM-6, and 402 Gb/s for 210 GBd PAM-4 signaling.
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. PP (07338724) , 1-11
Open AccessAdvanced Digital Signal Processing for 400 Gb/s/$\lambda$ IM/DD Intra Data Center Systems
This work presents an experimental study of 400 Gb/s/$\lambda$ targeted IM/DD systems in the O-band, which are of high relevance for next-generation 3.2 Tb/s short-reach Ethernet connections inside data centers. For such systems, advanced digital signal processing (DSP) has become essential to overcome bandwidth limitations and accumulated dispersion as dominant channel impairments. On a 2 km link, PAM-4, -6, and -8 as modulation formats, the use of pre-emphasis in the power-constrained transmitter, as well as precoding with the objective to break error bursts are analyzed. At the receiver, four DSP schemes are studied, including (1) full-response Volterra nonlinear equalization, (2) partial-response equalization implemented as Volterra equalization combined with a post-filter for channel shortening and subsequent sequence estimation, (3) duobinary-targeted equalization, combined with sequence estimation for duobinary decoding and (4) a machine-learning-based equalization and sequence estimation architecture. The experimental study is extended to 10 km transmission at wavelengths between 1290-1330 nm to quantify the impact of chromatic dispersion and define permissible wavelength ranges. Optimal DSP architectures are determined, depending on the modulation format and the signaling rate. The results demonstrate achievable information rates of 437 Gb/s for 160 GBd PAM-8, 412 Gb/s for 174 GBd PAM-6, and 402 Gb/s for 210 GBd PAM-4 signaling.
- 1 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 37 (15) , 845-848
Transmitter Compliance Metric Based on PAM-4 Duobinary Feedforward Equalization
The transmitter and dispersion eye closure quaternary (TDECQ) parameter for four-level amplitude modulation (PAM-4) systems assumes a reference receiver based on a linear feedforward equalizer (FFE). However, it is expected that for future generations of optical transceivers, as the symbol rate increases, a simple full-response FFE (FR-FFE) will not be able to reach the forward error correction (FEC) limit. A linear duobinary FFE (DB-FFE) can significantly improve performance under severe bandwidth limitations and might be used in the reference receiver. In this Letter, we present a novel transmitter compliance metric based on duobinary feedforward equalization. The method uses the standardized stress sequence and requires only minor changes to the standardized TDECQ computation. The metric provides excellent accuracy in severely bandwidth-limited optical systems affected by chromatic dispersion (CD). The maximum observed TDECQ estimation error in the CD range from −40 ps/nm to 10 ps/nm with the chirped transmitter is below 0.45 dB.
- 1 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 37 (15) , 845-848
Transmitter Compliance Metric Based on PAM-4 Duobinary Feedforward Equalization
The transmitter and dispersion eye closure quaternary (TDECQ) parameter for four-level amplitude modulation (PAM-4) systems assumes a reference receiver based on a linear feedforward equalizer (FFE). However, it is expected that for future generations of optical transceivers, as the symbol rate increases, a simple full-response FFE (FR-FFE) will not be able to reach the forward error correction (FEC) limit. A linear duobinary FFE (DB-FFE) can significantly improve performance under severe bandwidth limitations and might be used in the reference receiver. In this Letter, we present a novel transmitter compliance metric based on duobinary feedforward equalization. The method uses the standardized stress sequence and requires only minor changes to the standardized TDECQ computation. The metric provides excellent accuracy in severely bandwidth-limited optical systems affected by chromatic dispersion (CD). The maximum observed TDECQ estimation error in the CD range from −40 ps/nm to 10 ps/nm with the chirped transmitter is below 0.45 dB.
- 3 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (20) , 7202-7210
MLSE Output Visualization and Transmitter Compliance Metric
Intensity-modulation and direct-detection (IMDD) systems using two- or four-level pulse amplitude modulation (PAM) are widely used in data centers (DC) optical links, passive optical networks (PON), short metro links, and many other applications. The transmitted optical signal is distorted by noise, intersymbol interference (ISI), and nonlinearities caused by optical/electrical components and fiber. Therefore, the received signal must be recovered by an equalization technique that is realized either in the analog or digital domain or a combination thereof. Continuous-time linear equalizers (CTLE) and few-tap linear feed-forward equalizers (FFE) are often used in IMDD receivers. Besides bit error rate (BER) and symbol error rate (SER), the reconstructed one-dimensional modulation format signals are frequently characterized by eye diagrams and histograms. Complex modulation formats can be analyzed similarly by e.g., plotting eye diagrams and histograms per dimension. Equalized signal visualization tools are beneficial in assessing signal performance, sensitivity to clock jitter variations, amount of noise that can be added to the received signal to meet the forward error correction (FEC) threshold, etc. It is straightforward to generate an eye diagram after the FFE or after the decision feedback equalizer (DFE). However, the next generation of optical transceivers will likely be based on a computationally complex Volterra equalizer followed by a noise decorrelator and a maximum likelihood sequence estimation (MLSE) or a maximum a posteriori probability (MAP) algorithm. In this paper, we introduce a novel method for histogram reconstruction after the MLSE/MAP. The histogram reconstruction is extended to the plotting of the MLSE/MAP eye diagram. As some standardization bodies already consider an MLSE reference receiver to estimate transmitter dispersion eye closure quaternary (TDECQ), we use our MLSE-based histogram reconstruction method and upgrade the conventional FFE-based TDECQ technique to develop a very accurate technique for TDECQ calculation in FFE-MLSE receivers.
- 3 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (20) , 7202-7210
MLSE Output Visualization and Transmitter Compliance Metric
Intensity-modulation and direct-detection (IMDD) systems using two- or four-level pulse amplitude modulation (PAM) are widely used in data centers (DC) optical links, passive optical networks (PON), short metro links, and many other applications. The transmitted optical signal is distorted by noise, intersymbol interference (ISI), and nonlinearities caused by optical/electrical components and fiber. Therefore, the received signal must be recovered by an equalization technique that is realized either in the analog or digital domain or a combination thereof. Continuous-time linear equalizers (CTLE) and few-tap linear feed-forward equalizers (FFE) are often used in IMDD receivers. Besides bit error rate (BER) and symbol error rate (SER), the reconstructed one-dimensional modulation format signals are frequently characterized by eye diagrams and histograms. Complex modulation formats can be analyzed similarly by e.g., plotting eye diagrams and histograms per dimension. Equalized signal visualization tools are beneficial in assessing signal performance, sensitivity to clock jitter variations, amount of noise that can be added to the received signal to meet the forward error correction (FEC) threshold, etc. It is straightforward to generate an eye diagram after the FFE or after the decision feedback equalizer (DFE). However, the next generation of optical transceivers will likely be based on a computationally complex Volterra equalizer followed by a noise decorrelator and a maximum likelihood sequence estimation (MLSE) or a maximum a posteriori probability (MAP) algorithm. In this paper, we introduce a novel method for histogram reconstruction after the MLSE/MAP. The histogram reconstruction is extended to the plotting of the MLSE/MAP eye diagram. As some standardization bodies already consider an MLSE reference receiver to estimate transmitter dispersion eye closure quaternary (TDECQ), we use our MLSE-based histogram reconstruction method and upgrade the conventional FFE-based TDECQ technique to develop a very accurate technique for TDECQ calculation in FFE-MLSE receivers.
- Open Access
200Gb/s VCSEL transmission using 60m OM4 MMF and KP4 FEC for AI computing clusters
We show a beyond 200Gb/s VCSEL transmission experiment. Results are based on 35GHz VCSEL and advanced DSP. We show an AIR of 245Gb/s PAM-6 back-to-back, and 200Gb/s PAM-4 over 60m OM4 fiber assuming KP4-FEC.
Open Access200Gb/s VCSEL transmission using 60m OM4 MMF and KP4 FEC for AI computing clusters
We show a beyond 200Gb/s VCSEL transmission experiment. Results are based on 35GHz VCSEL and advanced DSP. We show an AIR of 245Gb/s PAM-6 back-to-back, and 200Gb/s PAM-4 over 60m OM4 fiber assuming KP4-FEC.
- 1 January 2024
- Published by Optica Publishing Group
- p. M2B.5
Investigation of Concatenated KP4 FEC with Single-Parity-Check Codes for Short-Reach IM/DD Systems
We investigate the concatenation of KP4 FEC with short single-parity-check codes. This represents an intermediate solution in terms of performance, complexity and latency between standalone KP4 FEC and concatenated schemes based on stronger soft-decision codes.
- 1 January 2024
- Published by Optica Publishing Group
- p. M2B.5
Investigation of Concatenated KP4 FEC with Single-Parity-Check Codes for Short-Reach IM/DD Systems
We investigate the concatenation of KP4 FEC with short single-parity-check codes. This represents an intermediate solution in terms of performance, complexity and latency between standalone KP4 FEC and concatenated schemes based on stronger soft-decision codes.
- 12 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Digital Signal Processing for 1.6 Tb/s+ Intra-Data Center Networks
Next generation intra-data center links will be operating at 1.6 Tb/s. Intensity modulation and direct detection together with pulse amplitude modulation is regarded as the most cost-efficient and practical solution. We review the challenges for digital signal processing enabling rates of 200 Gb/s/λ and beyond.
- 12 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Digital Signal Processing for 1.6 Tb/s+ Intra-Data Center Networks
Next generation intra-data center links will be operating at 1.6 Tb/s. Intensity modulation and direct detection together with pulse amplitude modulation is regarded as the most cost-efficient and practical solution. We review the challenges for digital signal processing enabling rates of 200 Gb/s/λ and beyond.
- 29 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (16) , 5373-5382
Probabilistic Shaping for High-Speed Unamplified IM/DD Systems With an O-Band EML
Probabilistic constellation shaping has been used in long-haul optically amplified coherent systems for its capability to approach the Shannon limit and realize fine rate granularity. The availability of high-bandwidth optical-electronic components and the previously mentioned advantages have invigorated researchers to explore probabilistic shaping (PS) in intensity-modulation and direct-detection (IM/DD) systems. This article presents an extensive comparison of uniform 8-ary pulse amplitude modulation (PAM) with PS PAM-8 using cap and cup Maxwell-Boltzmann (MB) distributions as well as MB distributions of different Gaussian orders. We report that in the presence of linear equalization, PS-PAM-8 outperforms uniform PAM-8 in terms of bit error ratio, achievable information rate and operational net bit rate indicating that cap-shaped PS-PAM-8 shows high tolerance against nonlinearities. In this paper, we have focused our investigations on O-band electro-absorption modulated laser unamplified IM/DD systems, which are operated close to the zero dispersion wavelength.
- 29 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (16) , 5373-5382
Probabilistic Shaping for High-Speed Unamplified IM/DD Systems With an O-Band EML
Probabilistic constellation shaping has been used in long-haul optically amplified coherent systems for its capability to approach the Shannon limit and realize fine rate granularity. The availability of high-bandwidth optical-electronic components and the previously mentioned advantages have invigorated researchers to explore probabilistic shaping (PS) in intensity-modulation and direct-detection (IM/DD) systems. This article presents an extensive comparison of uniform 8-ary pulse amplitude modulation (PAM) with PS PAM-8 using cap and cup Maxwell-Boltzmann (MB) distributions as well as MB distributions of different Gaussian orders. We report that in the presence of linear equalization, PS-PAM-8 outperforms uniform PAM-8 in terms of bit error ratio, achievable information rate and operational net bit rate indicating that cap-shaped PS-PAM-8 shows high tolerance against nonlinearities. In this paper, we have focused our investigations on O-band electro-absorption modulated laser unamplified IM/DD systems, which are operated close to the zero dispersion wavelength.