Tajeddine Benbarrad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tajeddine Benbarrad has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Mounir Arioua
National School Of Applied Sciences, Abdelmalek Essaâdi University
3 shared publicationsHatim Anas
Cadi Ayyad University
2 shared publications- Mounir Arioua
Abdelmalek Essaadi University
2 shared publications - Fatiha Elouaai
University Abdelmalek Essaâdi
1 shared publication - Lamiae Eloutouate
Abdelmalek Essaadi University
1 shared publication Marouane Salhaoui
Universidad Politécnica de Cartagena
1 shared publication
Latest Publications
- 12 March 2023
- Published by Springer Nature
- p. 235-244
Compression-Based Data Augmentation for CNN Generalization
- 12 March 2023
- Published by Springer Nature
- p. 235-244
Compression-Based Data Augmentation for CNN Generalization
- 1 January 2022
- Published by Springer Nature
- p. 977-988
Performance Evaluation of Transfer Learning for Surface Defect Classification
- 1 January 2022
- Published by Springer Nature
- p. 977-988
Performance Evaluation of Transfer Learning for Surface Defect Classification
- 1 January 2022
- Published by Springer Nature
- p. 901-911
Impact of Standard Image Compression on the Performance of Image Classification with Deep Learning
- 1 January 2022
- Published by Springer Nature
- p. 901-911
Impact of Standard Image Compression on the Performance of Image Classification with Deep Learning
- Open Access
- 16 December 2021
- Published by MDPI AG in Journal of Sensor and Actuator Networks
- Vol. 10 (4) , 73
Impact of Image Compression on the Performance of Steel Surface Defect Classification with a CNN
Machine vision is increasingly replacing manual steel surface inspection. The automatic inspection of steel surface defects makes it possible to ensure the quality of products in the steel industry with high accuracy. However, the optimization of inspection time presents a great challenge for the integration of machine vision in high-speed production lines. In this context, compressing the collected images before transmission is essential to save bandwidth and energy, and improve the latency of vision applications. The aim of this paper was to study the impact of quality degradation resulting from image compression on the classification performance of steel surface defects with a CNN. Image compression was applied to the Northeastern University (NEU) surface-defect database with various compression ratios. Three different models were trained and tested with these images to classify surface defects using three different approaches. The obtained results showed that trained and tested models on the same compression qualities maintained approximately the same classification performance for all used compression grades. In addition, the findings clearly indicated that the classification efficiency was affected when the training and test datasets were compressed using different parameters. This impact was more obvious when there was a large difference between these compression parameters, and for models that achieved very high accuracy. Finally, it was found that compression-based data augmentation significantly increased the classification precision to perfect scores (98–100%), and thus improved the generalization of models when tested on different compression qualities. The importance of this work lies in exploiting the obtained results to successfully integrate image compression into machine vision systems, and as appropriately as possible.
- 16 December 2021
- Published by MDPI AG in Journal of Sensor and Actuator Networks
- Vol. 10 (4) , 73
Open AccessImpact of Image Compression on the Performance of Steel Surface Defect Classification with a CNN
Machine vision is increasingly replacing manual steel surface inspection. The automatic inspection of steel surface defects makes it possible to ensure the quality of products in the steel industry with high accuracy. However, the optimization of inspection time presents a great challenge for the integration of machine vision in high-speed production lines. In this context, compressing the collected images before transmission is essential to save bandwidth and energy, and improve the latency of vision applications. The aim of this paper was to study the impact of quality degradation resulting from image compression on the classification performance of steel surface defects with a CNN. Image compression was applied to the Northeastern University (NEU) surface-defect database with various compression ratios. Three different models were trained and tested with these images to classify surface defects using three different approaches. The obtained results showed that trained and tested models on the same compression qualities maintained approximately the same classification performance for all used compression grades. In addition, the findings clearly indicated that the classification efficiency was affected when the training and test datasets were compressed using different parameters. This impact was more obvious when there was a large difference between these compression parameters, and for models that achieved very high accuracy. Finally, it was found that compression-based data augmentation significantly increased the classification precision to perfect scores (98–100%), and thus improved the generalization of models when tested on different compression qualities. The importance of this work lies in exploiting the obtained results to successfully integrate image compression into machine vision systems, and as appropriately as possible.
- Top Cited PapersOpen Access
- 28 January 2021
- Published by MDPI AG in Journal of Sensor and Actuator Networks
- Vol. 10 (1) , 7
Intelligent Machine Vision Model for Defective Product Inspection Based on Machine Learning
Quality control is one of the industrial tasks most susceptible to be improved by implementing technological innovations. As an innovative technology, machine vision enables reliable and fast 24/7 inspections and helps producers to improve the efficiency of manufacturing operations. The accessible data by vision equipment will be used to identify and report defective products, understand the causes of deficiencies and allow rapid and efficient intervention in smart factories. From this perspective, the proposed machine vision model in this paper combines the identification of defective products and the continuous improvement of manufacturing processes by predicting the most suitable parameters of production processes to obtain a defect-free item. The suggested model exploits all generated data by various integrated technologies in the manufacturing chain, thus meeting the requirements of quality management in the context of Industry 4.0, based on predictive analysis to identify patterns in data and suggest corrective actions to ensure product quality. In addition, a comparative study between several machine learning algorithms, both for product classification and process improvement models, is performed in order to evaluate the designed system. The results of this study show that the proposed model largely meets the requirements for the proper implementation of these techniques.
- 28 January 2021
- Published by MDPI AG in Journal of Sensor and Actuator Networks
- Vol. 10 (1) , 7
Top Cited PapersOpen AccessIntelligent Machine Vision Model for Defective Product Inspection Based on Machine Learning
Quality control is one of the industrial tasks most susceptible to be improved by implementing technological innovations. As an innovative technology, machine vision enables reliable and fast 24/7 inspections and helps producers to improve the efficiency of manufacturing operations. The accessible data by vision equipment will be used to identify and report defective products, understand the causes of deficiencies and allow rapid and efficient intervention in smart factories. From this perspective, the proposed machine vision model in this paper combines the identification of defective products and the continuous improvement of manufacturing processes by predicting the most suitable parameters of production processes to obtain a defect-free item. The suggested model exploits all generated data by various integrated technologies in the manufacturing chain, thus meeting the requirements of quality management in the context of Industry 4.0, based on predictive analysis to identify patterns in data and suggest corrective actions to ensure product quality. In addition, a comparative study between several machine learning algorithms, both for product classification and process improvement models, is performed in order to evaluate the designed system. The results of this study show that the proposed model largely meets the requirements for the proper implementation of these techniques.