Dongliang Ke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dongliang Ke has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Fengxiang Wang
Chinese Academy of Sciences
31 shared publications - Jose Rodriguez
Center for Energy Transition, Universidad San Sebastián, Santiago 8420524, Chile
13 shared publications - Yao Wei
Quanzhou Institute of Equipment Manufacturing, Haixi Institutes, Chinese Academy of Sciences, Quanzhou, China
13 shared publications - Hector Young
Department of Electrical Engineering, Universidad de La Frontera, Temuco, Chile
8 shared publications - Ralph Kennel
Chair of High-Power Converter Systems, TUM School of Engineering and Design, Technical University of Munich, Munich, Germany
7 shared publications - Xinhong Yu
Quanzhou Institute of Equipment Manufacturing, Haixi Institutes, Chinese Academy of Sciences, Quanzhou, China
6 shared publications
Latest Publications
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (7) , 10867-10880
Interturn Short Circuit Fault Diagnosis Strategy for Induction Motors Considering System Nonidealities
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (7) , 10867-10880
Interturn Short Circuit Fault Diagnosis Strategy for Induction Motors Considering System Nonidealities
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Disturbance Rejection Enhanced Two-Degree-of-Freedom Current Controller using Active Damping Function for PMSM System
The two-degree-of-freedom (2-DoF) control strategy is widely used in motor drives to decouple their control performances. However, due to the negative impacts caused by DC and AC disturbances, the disturbance rejection ability of this strategy cannot fully satisfy the strict requirements of some high-precision permanent magnet synchronous motor (PMSM) drive applications. Notably, a variety of sophisticated observers proposed in existing PMSM drive research can also be categorized as 2-DoF control architectures, yet they are typically plagued by intricate implementation procedures and high computational burdens. To address this issue, this paper proposes a new 2-DoF controller based on an active damping function.Based on the disturbance transfer function, the active damping function is designed and analyzed in the continuous domain to suppress low-frequency and high-frequency disturbances. The system performance in the case of parameter mismatch is also analyzed.In addition, different from existing literature, in this paper’s analysis, the influence of noise on the controller was considered to provide a basis for parameter design. Finally, experiments were conducted to verify the performance of the 2-DoF controller based on the active damping function proposed in this paper.
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Disturbance Rejection Enhanced Two-Degree-of-Freedom Current Controller using Active Damping Function for PMSM System
The two-degree-of-freedom (2-DoF) control strategy is widely used in motor drives to decouple their control performances. However, due to the negative impacts caused by DC and AC disturbances, the disturbance rejection ability of this strategy cannot fully satisfy the strict requirements of some high-precision permanent magnet synchronous motor (PMSM) drive applications. Notably, a variety of sophisticated observers proposed in existing PMSM drive research can also be categorized as 2-DoF control architectures, yet they are typically plagued by intricate implementation procedures and high computational burdens. To address this issue, this paper proposes a new 2-DoF controller based on an active damping function.Based on the disturbance transfer function, the active damping function is designed and analyzed in the continuous domain to suppress low-frequency and high-frequency disturbances. The system performance in the case of parameter mismatch is also analyzed.In addition, different from existing literature, in this paper’s analysis, the influence of noise on the controller was considered to provide a basis for parameter design. Finally, experiments were conducted to verify the performance of the 2-DoF controller based on the active damping function proposed in this paper.
- 3 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (3) , 5064-5077
Generalized Unbiased Parameters Identification for PMSM Based on Information Enrichment and Convergence Correction
Accurate multiparameter estimation in permanent magnet synchronous motors (PMSMs) is essential for high-performance control. However, gradient-descent-based methods, widely adopted for this purpose, are inherently biased, and the simultaneous identification of multiple parameters without external signal injection remains challenging. This work introduces an information enrichment strategy and a convergence correction method to overcome these limitations. An evaluation function is first established to quantitatively relate the information content of experimental conditions to estimation accuracy, providing a rigorous foundation for multiparameter identification. By adjusting the drive system and implementing a customized data preselection strategy, the proposed approach ensures the acquisition of information-rich data necessary for accurate estimation of four key PMSM parameters. Moreover, this study analytically derives, for the first time, the inherent bias in gradient-descent-based estimators within the PMSM. Leveraging these findings, a generalized, unbiased, and iterative identification framework is proposed to enable high-precision multiparameter estimation. Comparative validations confirm the effectiveness and robustness of the proposed method.
- 3 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (3) , 5064-5077
Generalized Unbiased Parameters Identification for PMSM Based on Information Enrichment and Convergence Correction
Accurate multiparameter estimation in permanent magnet synchronous motors (PMSMs) is essential for high-performance control. However, gradient-descent-based methods, widely adopted for this purpose, are inherently biased, and the simultaneous identification of multiple parameters without external signal injection remains challenging. This work introduces an information enrichment strategy and a convergence correction method to overcome these limitations. An evaluation function is first established to quantitatively relate the information content of experimental conditions to estimation accuracy, providing a rigorous foundation for multiparameter identification. By adjusting the drive system and implementing a customized data preselection strategy, the proposed approach ensures the acquisition of information-rich data necessary for accurate estimation of four key PMSM parameters. Moreover, this study analytically derives, for the first time, the inherent bias in gradient-descent-based estimators within the PMSM. Leveraging these findings, a generalized, unbiased, and iterative identification framework is proposed to enable high-precision multiparameter estimation. Comparative validations confirm the effectiveness and robustness of the proposed method.
- 30 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (6) , 8366-8378
Selective Forgetting-Based Unbiased Estimation of PMSM Parameters Under Complex Operating Conditions and Measurement Noise
Accurate parameter estimation for permanent magnet synchronous motors (PMSMs) under complex operating conditions is challenging, as not all frequency components of the input signal contribute equally to parameter estimation, and not all sampled data are equally informative. This article presents a theoretical analysis of how specific frequency components influence the estimation of individual PMSM parameters. Based on these insights, a selective forgetting mechanism is proposed to enhance estimation accuracy by retaining informative data while discarding outdated information in targeted parameter directions. In parallel, an instrumental variable method is employed to inject new information while mitigating the adverse effects of measurement noise. To ensure real-time feasibility, a computationally efficient inversion scheme for the information matrix is designed, significantly reducing the algorithm’s complexity. The resulting method achieves high-accuracy, unbiased parameter estimation with strong robustness across diverse operating conditions. Comparative simulations validate the effectiveness and superiority of the proposed approach.
- 30 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (6) , 8366-8378
Selective Forgetting-Based Unbiased Estimation of PMSM Parameters Under Complex Operating Conditions and Measurement Noise
Accurate parameter estimation for permanent magnet synchronous motors (PMSMs) under complex operating conditions is challenging, as not all frequency components of the input signal contribute equally to parameter estimation, and not all sampled data are equally informative. This article presents a theoretical analysis of how specific frequency components influence the estimation of individual PMSM parameters. Based on these insights, a selective forgetting mechanism is proposed to enhance estimation accuracy by retaining informative data while discarding outdated information in targeted parameter directions. In parallel, an instrumental variable method is employed to inject new information while mitigating the adverse effects of measurement noise. To ensure real-time feasibility, a computationally efficient inversion scheme for the information matrix is designed, significantly reducing the algorithm’s complexity. The resulting method achieves high-accuracy, unbiased parameter estimation with strong robustness across diverse operating conditions. Comparative simulations validate the effectiveness and superiority of the proposed approach.
- 3 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 41 (2) , 1198-1208
Current Ripple Suppression for PMSM Predictive Control System Under DC-Link Voltage Fluctuation
In permanent magnet synchronous motor (PMSM) drive systems, DC-link voltage fluctuations can severely affect the steady-state performance of the system. Although traditional model-free predictive current control (MF-PCC) can enhance system robustness and reduce the impact of current harmonics, its current harmonics caused by DC-link voltage fluctuations can not be suppressed effectively. To solve this problem, this paper proposes a current ripple suppression predictive current control strategy based on a dual second-order generalized integrator (DSOGI). This strategy utilizes the DSOGI to extract fluctuation signals from the current signals that have the same frequency as the DC-link voltage fluctuations, achieving dynamic reverse compensation of the current ripple. Additionally, to address the signal delay issue associated with the DSOGI algorithm, the Lagrange interpolation method is employed to predict the signal and, in doing so, the compensation accuracy is improved. The experimental results verify the effectiveness of the proposed method. Compared to traditional methods, the proposed approach effectively reduces current ripple caused by DC-link voltage fluctuations and enhances the control system robustness.
- 3 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 41 (2) , 1198-1208
Current Ripple Suppression for PMSM Predictive Control System Under DC-Link Voltage Fluctuation
In permanent magnet synchronous motor (PMSM) drive systems, DC-link voltage fluctuations can severely affect the steady-state performance of the system. Although traditional model-free predictive current control (MF-PCC) can enhance system robustness and reduce the impact of current harmonics, its current harmonics caused by DC-link voltage fluctuations can not be suppressed effectively. To solve this problem, this paper proposes a current ripple suppression predictive current control strategy based on a dual second-order generalized integrator (DSOGI). This strategy utilizes the DSOGI to extract fluctuation signals from the current signals that have the same frequency as the DC-link voltage fluctuations, achieving dynamic reverse compensation of the current ripple. Additionally, to address the signal delay issue associated with the DSOGI algorithm, the Lagrange interpolation method is employed to predict the signal and, in doing so, the compensation accuracy is improved. The experimental results verify the effectiveness of the proposed method. Compared to traditional methods, the proposed approach effectively reduces current ripple caused by DC-link voltage fluctuations and enhances the control system robustness.
- 17 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 17061-17072
D-Axis High-Frequency Impedance Extraction Method for Online Diagnosis of Inter-Turn Short-Circuit Faults in Traction Motors
As a critical component of high-speed trains, traction motors are responsible for the conversion of mechanical and electrical energy. However, interturn short circuit (ITSC) faults in stator windings pose a significant challenge to their safe and reliable operation. This article presents an online method for diagnosing ITSC faults in traction induction motors by injecting a high-frequency voltage signal into the d-axis and analyzing the extracted high-frequency impedance of the d-axis. First, an ITSC model for induction motors is established, and the impedance characteristics of faulty traction motors are analyzed using a finite element (FE) method. Second, the d-axis impedance model of a motor with ITSC faults is developed under high-frequency square-wave voltage injection, providing an in-depth perspective on the impact of ITSC faults on the motor’s high-frequency impedance. In addition, the influence of control delays on impedance extraction and quantization error from the analog-to-digital (A/D) conversion are analyzed. Finally, the Goertzel algorithm is utilized to extract the high-frequency current response of the d-axis from the high-frequency square wave voltage after injection, allowing the calculation of the high-frequency impedance of the motor on the d-axis. The fault diagnosis is then implemented on the basis of the average modulus of high-frequency d-axis impedance. Experimental results are provided to demonstrate the efficacy of this diagnostic method. The proposed method accurately diagnoses ITSC faults online at low speeds or standstill by injecting low-amplitude high-frequency voltage, with minimal impact on motor operation.
- 17 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 17061-17072
D-Axis High-Frequency Impedance Extraction Method for Online Diagnosis of Inter-Turn Short-Circuit Faults in Traction Motors
As a critical component of high-speed trains, traction motors are responsible for the conversion of mechanical and electrical energy. However, interturn short circuit (ITSC) faults in stator windings pose a significant challenge to their safe and reliable operation. This article presents an online method for diagnosing ITSC faults in traction induction motors by injecting a high-frequency voltage signal into the d-axis and analyzing the extracted high-frequency impedance of the d-axis. First, an ITSC model for induction motors is established, and the impedance characteristics of faulty traction motors are analyzed using a finite element (FE) method. Second, the d-axis impedance model of a motor with ITSC faults is developed under high-frequency square-wave voltage injection, providing an in-depth perspective on the impact of ITSC faults on the motor’s high-frequency impedance. In addition, the influence of control delays on impedance extraction and quantization error from the analog-to-digital (A/D) conversion are analyzed. Finally, the Goertzel algorithm is utilized to extract the high-frequency current response of the d-axis from the high-frequency square wave voltage after injection, allowing the calculation of the high-frequency impedance of the motor on the d-axis. The fault diagnosis is then implemented on the basis of the average modulus of high-frequency d-axis impedance. Experimental results are provided to demonstrate the efficacy of this diagnostic method. The proposed method accurately diagnoses ITSC faults online at low speeds or standstill by injecting low-amplitude high-frequency voltage, with minimal impact on motor operation.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (9) , 13977-13990
Multiobjective Model Predictive Control of LCL Grid-Connected Inverter Based on an Improved Gray Wolf Algorithm
To address the challenges of high-current harmonic distortion, excessive switching losses, and less desirable dynamic response in the single-phase LCL grid-connected inverter, this article proposes a multiobjective model predictive control (MOMPC) method based on an improved gray wolf optimization (IGWO) algorithm. The proposed method first establishes the mathematical model of the LCL inverter and formulates the cost function of FCS-MPC. Subsequently, the voltage of the capacitor is introduced to impose constraints on the cost function, thereby constructing the MOMPC to further enhance the control performance. Finally, the IGWO algorithm is employed to perform offline multiobjective optimization on current error, total harmonic distortion, and switching frequency to design the optimal weighting coefficients of MOMPC. In contrast to traditional MPC methods, the IGWO-based MOMPC can reduce total harmonic distortion, switching frequency, and control errors while enhancing system robustness and dynamic performance. The simulation and experimental results validate the feasibility and effectiveness of the proposed method.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (9) , 13977-13990
Multiobjective Model Predictive Control of LCL Grid-Connected Inverter Based on an Improved Gray Wolf Algorithm
To address the challenges of high-current harmonic distortion, excessive switching losses, and less desirable dynamic response in the single-phase LCL grid-connected inverter, this article proposes a multiobjective model predictive control (MOMPC) method based on an improved gray wolf optimization (IGWO) algorithm. The proposed method first establishes the mathematical model of the LCL inverter and formulates the cost function of FCS-MPC. Subsequently, the voltage of the capacitor is introduced to impose constraints on the cost function, thereby constructing the MOMPC to further enhance the control performance. Finally, the IGWO algorithm is employed to perform offline multiobjective optimization on current error, total harmonic distortion, and switching frequency to design the optimal weighting coefficients of MOMPC. In contrast to traditional MPC methods, the IGWO-based MOMPC can reduce total harmonic distortion, switching frequency, and control errors while enhancing system robustness and dynamic performance. The simulation and experimental results validate the feasibility and effectiveness of the proposed method.
- 18 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (5) , 7707-7717
A Hybrid Model Flux Estimator for Diagnosis of Inter-Turn Short Circuit Fault in Traction Motors Considering Inverter Nonlinearity
Stator inter-turn short circuit (ITSC) faults are among the most severe malfunctions encountered in traction motors, significantly compromising the power output of high-speed trains. This paper presents an effective fault diagnosis method for detecting ITSC faults in traction motors, utilizing a voltage-current hybrid model flux estimator. The fault characterization signal is obtained using the PI module within the flux estimator, specifically designed to compensate for flux errors associated with pure integration and stator resistance measurements at low speeds. Firstly, a mathematical model of the induction motor under ITSC faults is established, and a high-precision voltage-current hybrid flux estimator based on deadbeat stator current observer is proposed. Secondly, the impact of ITSC faults and the characteristics of the inverter nonlinearity on the fault characterization signal is analyzed. Furthermore, an assessment is conducted on the influence of various parameter mismatches in the motor on the fault characterization signal. Finally, the efficacy of the proposed fault diagnosis method is validated through simulations and experiments conducted under diverse operating conditions.
- 18 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (5) , 7707-7717
A Hybrid Model Flux Estimator for Diagnosis of Inter-Turn Short Circuit Fault in Traction Motors Considering Inverter Nonlinearity
Stator inter-turn short circuit (ITSC) faults are among the most severe malfunctions encountered in traction motors, significantly compromising the power output of high-speed trains. This paper presents an effective fault diagnosis method for detecting ITSC faults in traction motors, utilizing a voltage-current hybrid model flux estimator. The fault characterization signal is obtained using the PI module within the flux estimator, specifically designed to compensate for flux errors associated with pure integration and stator resistance measurements at low speeds. Firstly, a mathematical model of the induction motor under ITSC faults is established, and a high-precision voltage-current hybrid flux estimator based on deadbeat stator current observer is proposed. Secondly, the impact of ITSC faults and the characteristics of the inverter nonlinearity on the fault characterization signal is analyzed. Furthermore, an assessment is conducted on the influence of various parameter mismatches in the motor on the fault characterization signal. Finally, the efficacy of the proposed fault diagnosis method is validated through simulations and experiments conducted under diverse operating conditions.
- 7 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (3) , 7367-7378
Low Prediction Error Model-Free Predictive Control on PMSM Drives With Ordinary Kriging Time-Shift
Model-free predictive control (MFPC) is developed to address the issue of the weak robustness in model predictive control (MPC) based on a physical model. In predictive control algorithms, the knowledge of future values of the reference is vital and this information is conventionally obtained using the Lagrange extrapolation algorithm. However, during implementation, numerical errors introduced by inaccurate time-shifts compromise the adaptability of the data-driven model and its accuracy to reflect the plant’s dynamics and operating states. To overcome these challenges, a time-series-based model-free predictive current control (MF-PCC) is proposed that employs the ordinary kriging (OK) algorithm in the continuous-control-set (CCS) type and applied to a permanent magnet synchronous motor (PMSM) driving system as a current controller. The prediction errors for the time-series model with the typical prediction and ultralocalized time-series structure are analyzed in the CCS type. Based on this time-series model, state variables are predicted by the time-shift using the OK algorithm, replacing the Lagrange-based approach in the conventional methods, to reduce the prediction error. Both simulation and experimental results demonstrate the effectiveness of the proposed method, highlighting its superiorities in current quality and model accuracy, as well as its enhanced robustness.
- 7 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (3) , 7367-7378
Low Prediction Error Model-Free Predictive Control on PMSM Drives With Ordinary Kriging Time-Shift
Model-free predictive control (MFPC) is developed to address the issue of the weak robustness in model predictive control (MPC) based on a physical model. In predictive control algorithms, the knowledge of future values of the reference is vital and this information is conventionally obtained using the Lagrange extrapolation algorithm. However, during implementation, numerical errors introduced by inaccurate time-shifts compromise the adaptability of the data-driven model and its accuracy to reflect the plant’s dynamics and operating states. To overcome these challenges, a time-series-based model-free predictive current control (MF-PCC) is proposed that employs the ordinary kriging (OK) algorithm in the continuous-control-set (CCS) type and applied to a permanent magnet synchronous motor (PMSM) driving system as a current controller. The prediction errors for the time-series model with the typical prediction and ultralocalized time-series structure are analyzed in the CCS type. Based on this time-series model, state variables are predicted by the time-shift using the OK algorithm, replacing the Lagrange-based approach in the conventional methods, to reduce the prediction error. Both simulation and experimental results demonstrate the effectiveness of the proposed method, highlighting its superiorities in current quality and model accuracy, as well as its enhanced robustness.
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (7) , 6719-6730
Low-Stagnation Model-Free Predictive Current Control of PMSM Drives
As the updating frequency decreases, the stagnation effect poses a challenge to the accuracy of model-free predictive control (MFPC) based on signal gradients. To mitigate this issue from the perspective of sampled data, a low-stagnation model-free predictive current control (MF-PCC) strategy is proposed in this article and applied in permanent magnet synchronous motor (PMSM) drives. Recognizing that some elements of the sampled data do not contribute to accurately depict the motion characteristics and operational states of the system, a frequency-converting double second-order generalized integrator (FC-DSOGI) structure is improved and utilized to extract these elements and reinject them by a random gain, thereby generating a coercive difference to reduce the stagnation effect. Furthermore, fuzzy logic is developed to determine the optimal gains for the control law, thereby enhancing the control performance. The generalized universal model (GUM) is chosen as an illustrative case. Through experimental validation, the effectiveness of the proposed method is demonstrated with enhancements in current quality and model accuracy, alongside enhanced robustness. Moreover, it showcases the superiority of the low-stagnation over conventional control strategies.
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (7) , 6719-6730
Low-Stagnation Model-Free Predictive Current Control of PMSM Drives
As the updating frequency decreases, the stagnation effect poses a challenge to the accuracy of model-free predictive control (MFPC) based on signal gradients. To mitigate this issue from the perspective of sampled data, a low-stagnation model-free predictive current control (MF-PCC) strategy is proposed in this article and applied in permanent magnet synchronous motor (PMSM) drives. Recognizing that some elements of the sampled data do not contribute to accurately depict the motion characteristics and operational states of the system, a frequency-converting double second-order generalized integrator (FC-DSOGI) structure is improved and utilized to extract these elements and reinject them by a random gain, thereby generating a coercive difference to reduce the stagnation effect. Furthermore, fuzzy logic is developed to determine the optimal gains for the control law, thereby enhancing the control performance. The generalized universal model (GUM) is chosen as an illustrative case. Through experimental validation, the effectiveness of the proposed method is demonstrated with enhancements in current quality and model accuracy, alongside enhanced robustness. Moreover, it showcases the superiority of the low-stagnation over conventional control strategies.