Malgorzata Kowalik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Malgorzata Kowalik has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Adri C. T. van Duin
The Pennsylvania State University
2 shared publications - Aditya Lele
Department of Mechanical Engineering, The Pennsylvania State University, University Park, PA 16802, USA
1 shared publication - Eric W. Hudson
Department of Physics The Pennsylvania State University 16802 University Park PA USA
1 shared publication - Gregory M. Odegard
Michigan Technological University
1 shared publication - Ivan Gallegos
Michigan Technological University, Houghton, USA
1 shared publication - Jacob Gissinger
National Aeronautics and Space Administration
1 shared publication
Latest Publications
- Open Access
- 21 May 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Establishing Physical and Chemical Mechanisms of Polymerization and Pyrolysis of Phenolic Resins for Carbon-Carbon Composites
The complex structural and chemical changes that occur during polymerization and pyrolysis critically affect material properties but are difficult to characterize in situ. This work presents a novel, experimentally validated methodology for modeling the complete polymerization and pyrolysis processes for phenolic resin using reactive molecular dynamics. The polymerization simulations produced polymerized structures with mass densities of 1.24 ± 0.01 g/cm3 and Young’s moduli of 3.50 ± 0.64 GPa, which are in good agreement with experimental values. The structural properties of the subsequently pyrolyzed structures were also found to be in good agreement with experimental X-ray data for the phenolic-derived carbon matrices, with interplanar spacings of 3.81 ± 0.06 Å and crystallite heights of 10.94 ± 0.37 Å. The mass densities of the pyrolyzed models, 2.01 ± 0.03 g/cm3, correspond to skeletal density values, where the volume of pores is excluded in density calculations for the phenolic resin-based pyrolyzed samples. Young’s moduli are underpredicted at 122.36 ± 16.48 GPa relative to experimental values of 146 – 256 GPa for nanoscale amorphous carbon samples.
- 21 May 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessEstablishing Physical and Chemical Mechanisms of Polymerization and Pyrolysis of Phenolic Resins for Carbon-Carbon Composites
The complex structural and chemical changes that occur during polymerization and pyrolysis critically affect material properties but are difficult to characterize in situ. This work presents a novel, experimentally validated methodology for modeling the complete polymerization and pyrolysis processes for phenolic resin using reactive molecular dynamics. The polymerization simulations produced polymerized structures with mass densities of 1.24 ± 0.01 g/cm3 and Young’s moduli of 3.50 ± 0.64 GPa, which are in good agreement with experimental values. The structural properties of the subsequently pyrolyzed structures were also found to be in good agreement with experimental X-ray data for the phenolic-derived carbon matrices, with interplanar spacings of 3.81 ± 0.06 Å and crystallite heights of 10.94 ± 0.37 Å. The mass densities of the pyrolyzed models, 2.01 ± 0.03 g/cm3, correspond to skeletal density values, where the volume of pores is excluded in density calculations for the phenolic resin-based pyrolyzed samples. Young’s moduli are underpredicted at 122.36 ± 16.48 GPa relative to experimental values of 146 – 256 GPa for nanoscale amorphous carbon samples.
- Open Access
Atomistic-Scale Simulations on Graphene Bending Near a Copper Surface
Molecular insights into graphene-catalyst surface interactions can provide useful information for the efficient design of copper current collectors with graphitic anode interfaces. As graphene bending can affect the local electron density, it should reflect its local reactivity as well. Using ReaxFF reactive molecular simulations, we have investigated the possible bending of graphene in vacuum and near copper surfaces. We describe the energy cost for graphene bending and the binding energy with hydrogen and copper with two different ReaxFF parameter sets, demonstrating the relevance of using the more recently developed ReaxFF parameter sets for graphene properties. Moreover, the draping angle at copper step edges obtained from our atomistic simulations is in good agreement with the draping angle determined from experimental measurements, thus validating the ReaxFF results.
Open AccessAtomistic-Scale Simulations on Graphene Bending Near a Copper Surface
Molecular insights into graphene-catalyst surface interactions can provide useful information for the efficient design of copper current collectors with graphitic anode interfaces. As graphene bending can affect the local electron density, it should reflect its local reactivity as well. Using ReaxFF reactive molecular simulations, we have investigated the possible bending of graphene in vacuum and near copper surfaces. We describe the energy cost for graphene bending and the binding energy with hydrogen and copper with two different ReaxFF parameter sets, demonstrating the relevance of using the more recently developed ReaxFF parameter sets for graphene properties. Moreover, the draping angle at copper step edges obtained from our atomistic simulations is in good agreement with the draping angle determined from experimental measurements, thus validating the ReaxFF results.