CVCarlos Roberto Vargas-Llanos

Carlos Roberto Vargas-Llanos

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Carlos Roberto Vargas-Llanos has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Design and test of a setup for calorimetric measurements of AC transport losses in HTS racetrack coils

    by Carlos Roberto Vargas-Llanos, Joachim Krämer, Mathias Noe, Francesco Grilli

    The estimation and measurement of AC losses in coils based on high-temperature superconductors (HTS) are relevant aspects of HTS applications. They influence the cooling power requirement, operating temperature and efficiency, which can be decisive in the construction and implementation of superconducting equipment, such as superconducting electrical machines. The measurement of losses due to AC transport current (without external magnetic field) is not an easy task. Several efforts have been made to measure these AC transport losses in superconducting coils with a calorimetric approach by trying to minimize the influence of the environment, improve the accuracy and ensure the reproducibility of the results. This work presents the design and construction of a setup to measure transport AC losses in high-temperature superconducting coils based on a calorimetric approach (boil-off method). The evaporated cryogen (nitrogen) related to the dissipation of energy is collected by using a 3D printed bubble collector that guides the gas into a flow sensor. A box-inside-a-box approach is used to surround the measurement chamber with a cryogenic environment. This approach allows re-directing the heat transfer from the surroundings into an intermediate zone (space between external and internal box). Since this intermediate zone operates under cryogenic temperatures, the noise and the heat transfer in the internal part of the setup are reduced. A statistical analysis of the results based on a standard load cycle, average value, and standard deviation calculations allows assessing the variability in the measurements and expressing the results as average value and uncertainty range. The calibration and reproducibility of the measurements are verified with a set of resistors under different conditions and during different weeks. Finally, the AC transport losses in a racetrack coil for an electrical machine application are measured and compared with 3D simulation results based on the homogenization of the T-A formulation.


  • Open Access

    3D homogenization of the T-A formulation for the analysis of coils with complex geometries

    by Carlos Roberto Vargas-Llanos, Felix Huber, Nicolò Riva, Min Zhang, Francesco Grilli

    The modeling and analysis of superconducting coils is an essential task in the design stage of most devices based on high-temperature superconductors (HTS). These calculations allow verifying basic estimations and assumptions, proposing improvements, and computing quantities that are not easy to calculate with an analytical approach. For instance, the estimation of losses in HTS is fundamental during the design stage since losses can strongly influence the cooling system requirements and operating temperature. Typically, 2D finite element analysis is used to calculate AC losses in HTS, due to the lack of analytical solutions that can accurately represent complex operating conditions, such as AC transport current and AC external applied magnetic field in coils. These 2D models are usually a representation of an infinitely long arrangement. Therefore, they cannot be used to analyze end effects and complex 3D configurations. In this publication, we use the homogenization of the T-A formulation in 3D for the analysis of superconducting coils with complex geometries where a 2D approach cannot provide accurate analyses and verification of assumptions. The modeling methodology allows an easier implementation in commercial software (COMSOL Multiphysics) in comparison with the currently available 3D H homogenization, despite the complexity of the geometry. This methodology is first validated with a racetrack coil (benchmark case) by comparing the results with the well-established H formulation. Then, the electromagnetic behavior of coils with more complex geometries is analyzed.


  • Influence of Coil Position on AC Losses of Stator Superconducting Windings of a Synchronous Machine for a 10 MW Wind Turbine

    by Carlos Roberto Vargas-Llanos, Sebastian Lengsfeld, Mathias Noe, Tabea Arndt, Francesco Grilli

    One of the main tasks during the design of a superconducting electrical machine is the estimation of losses in the superconducting coils. These losses can be decisive in such applications since they influence the cooling power requirements and the overall efficiency of the machine. In this article, we focus on the dissipation in the stator superconducting coils of a synchronous machine. The calculations are done within the framework of the SupraGenSys project, which aims to develop a new superconducting generator for the wind energy sector. A detailed study of the ac losses in the stator coils is carried out based on a basic design that considers the main constraints of this application. The objective is to look for an optimum solution for the level and distribution of losses as a second step in the design process. The T-A formulation of Maxwell's equations is used in a 2-D finite-element model to analyze the behavior of the magnetic field around the coils and calculate losses. Particular attention is given to the position of the coils inside a slot and several coil configurations are presented. It is shown that certain coil arrangements lead to a significantly lower total loss, a more uniform loss distribution, which ultimately leads to the possibility of increasing the operating temperature.


  • Open Access

    T-A Formulation for the Design and AC Loss Calculation of a Superconducting Generator for a 10 MW Wind Turbine

    by Carlos Roberto Vargas-Llanos, Sebastian Lengsfeld, Francesco Grilli

    The current capacity of high-temperature superconductors (HTS) has encouraged several applications of these materials in electric power systems. These applications in electrical machines represent a promising solution for more compact and efficient designs. Despite no measurable resistance in the superconducting state, HTS could experience losses under time changing transport current or magnetic field. Therefore, loss estimation is a key input for the design. Maxwell’s equations in the T-A formulation form can be used to model and estimate losses in the superconducting tapes of an electrical machine. This formulation requires the current as a function of time in each superconducting tape as an input. A methodology to calculate this current distribution is presented in this article. The procedure introduces a previous step in the building model process and allows a better connection of the machine design with the estimation of losses in the superconductor in order to get a more efficient machine. The approach is applied to a 10 MW superconducting generator, where over one thousand tapes cross-sections are modelled in 2D. The superconductor’s non-linear behaviour and critical current density anisotropy are considered. Losses are estimated for different designs and a sensitivity analysis is presented for different temperatures and frequencies, in addition to other alternatives to reduce losses.