Masaru Sato
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Masaru Sato has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Naoya Okamoto
Fujitsu Ltd., Atsugi, Japan
3 shared publications Toshihiro Ohki
Fujitsu Ltd., Atsugi, Japan
3 shared publications- Tsuyoshi Takahashi
Fujitsu Limited, 10-1 Morinosato-Wakamiya, Atsugi, Kanagawa 243-0197, Japan
3 shared publications Naoki Hara
Fujitsu Ltd., Atsugi, Japan
2 shared publications- Naoki Hara
The University of Tokyo
2 shared publications - Norikazu Nakamura
Fujitsu Ltd., Atsugi, Japan
2 shared publications
Latest Publications
- Open Access
- 18 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 965-973
High Output Power and Efficiency 300-GHz Band InP-Based MOS-HEMT Power Amplifiers With Composite-Channel and Double-Side Doping
This paper demonstrated high-output-power and high-efficiency power amplifier (PA) monolithic microwave-integrated circuit (MMIC) at 300-GHz band (252-296 GHz) with the use of InP-based metal-oxide-semiconductor high-electron-mobility transistors (HEMTs) with composite-channel (CC) and double-side-doping (DD) techniques. The CC-DD structure obtained high output current and low channel resistance due to the improved carrier density and mobility. W-band load-pull measurement revealed the drastically improved output power density of CC-DD structure compared with that of single-channel DD structure. The 2-stage cascaded, 4-way, and 16-way PA-MMICs were designed based on stacked common-gate transistors with current reuse topology. The cascaded PA-MMIC exhibited a power-added efficiency (PAE) of 7.8%, and the 16-way PA-MMIC exhibited an output power of 16.9 dBm. These values are the highest among all the values reported for the 300-GHz band PA-MMICs. The 4-way PA-MMIC achieved a high output power of 13.6-14.6 dBm and high PAE of 4.8%-6.3% simultaneously at the entire 300-GHz band.
- 18 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 965-973
Open AccessHigh Output Power and Efficiency 300-GHz Band InP-Based MOS-HEMT Power Amplifiers With Composite-Channel and Double-Side Doping
This paper demonstrated high-output-power and high-efficiency power amplifier (PA) monolithic microwave-integrated circuit (MMIC) at 300-GHz band (252-296 GHz) with the use of InP-based metal-oxide-semiconductor high-electron-mobility transistors (HEMTs) with composite-channel (CC) and double-side-doping (DD) techniques. The CC-DD structure obtained high output current and low channel resistance due to the improved carrier density and mobility. W-band load-pull measurement revealed the drastically improved output power density of CC-DD structure compared with that of single-channel DD structure. The 2-stage cascaded, 4-way, and 16-way PA-MMICs were designed based on stacked common-gate transistors with current reuse topology. The cascaded PA-MMIC exhibited a power-added efficiency (PAE) of 7.8%, and the 16-way PA-MMIC exhibited an output power of 16.9 dBm. These values are the highest among all the values reported for the 300-GHz band PA-MMICs. The 4-way PA-MMIC achieved a high output power of 13.6-14.6 dBm and high PAE of 4.8%-6.3% simultaneously at the entire 300-GHz band.
- 17 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (3) , 324-327
31 W/mm at 8 GHz in InAlGaN/GaN HEMT With Thermal CVD SiNx Passivation
The study reports the findings on a quaternary InAlGaN/GaN high electron mobility transistor (HEMT) employing a thermal chemical vapor deposition (TCVD) silicon nitride (SiN x ) passivation with a record high output power density of 31.0 W/mm in the X-band. We compared the two different SiN x passivation methods, namely, TCVD deposition, and plasma-enhanced CVD (PECVD) deposition, for InAlGaN/GaN HEMTs and investigated the effects on device performance. PECVD SiN x passivation caused a considerable degradation of the two-dimensional electron gas (2DEG) mobility. However, TCVD SiN x could suppress the degradation of 2DEG mobility, resulting in a low sheet resistance of 293 ohm/sq. with a high 2DEG mobility of 2048 cm 2 V -1 s -1 . Furthermore, InAlGaN/GaN HEMT with TCVD SiN x passivation exhibited a high-drain current of 1230 mA/mm even after off-state stress due to the reduced current collapse and low sheet resistance. The off-state breakdown voltage increased from 169 to 227 V on using TCVD SiN x despite an increase in the maximum drain current, resulting in a high voltage of 90 V at radiofrequency. We successfully demonstrated the state-of-the-art high output power density GaN-based HEMTs with an InAlGaN barrier and TCVD SiN x passivation. Our results revealed that TCVD SiN x passivation can facilitate the application of InAlGaN/GaN HEMTs for high-power amplifiers.
- 17 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (3) , 324-327
31 W/mm at 8 GHz in InAlGaN/GaN HEMT With Thermal CVD SiNx Passivation
The study reports the findings on a quaternary InAlGaN/GaN high electron mobility transistor (HEMT) employing a thermal chemical vapor deposition (TCVD) silicon nitride (SiN x ) passivation with a record high output power density of 31.0 W/mm in the X-band. We compared the two different SiN x passivation methods, namely, TCVD deposition, and plasma-enhanced CVD (PECVD) deposition, for InAlGaN/GaN HEMTs and investigated the effects on device performance. PECVD SiN x passivation caused a considerable degradation of the two-dimensional electron gas (2DEG) mobility. However, TCVD SiN x could suppress the degradation of 2DEG mobility, resulting in a low sheet resistance of 293 ohm/sq. with a high 2DEG mobility of 2048 cm 2 V -1 s -1 . Furthermore, InAlGaN/GaN HEMT with TCVD SiN x passivation exhibited a high-drain current of 1230 mA/mm even after off-state stress due to the reduced current collapse and low sheet resistance. The off-state breakdown voltage increased from 169 to 227 V on using TCVD SiN x despite an increase in the maximum drain current, resulting in a high voltage of 90 V at radiofrequency. We successfully demonstrated the state-of-the-art high output power density GaN-based HEMTs with an InAlGaN barrier and TCVD SiN x passivation. Our results revealed that TCVD SiN x passivation can facilitate the application of InAlGaN/GaN HEMTs for high-power amplifiers.
- Open Access
- 9 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 11, 101-106
24.4 W/mm X-Band GaN HEMTs on AlN Substrates With the LPCVD-Grown High-Breakdown-Field SiN x Layer
This paper reports on an AlGaN/GaN high-electron-mobility transistor (HEMT) on free-standing AlN substrates with a record-high output power density of 24.4 W/mm at the X-band. A high-drain current operation of 1.4 A/mm was realized by employing high-density 2-dimensional electron gas channel and regrown Ohmic contacts. Furthermore, a high-voltage operation of 110 V was achieved owing to the high-density and high-breakdown SiNx layer grown by low-pressure/high-temperature chemical vapor deposition. Three-stage AlGaN buffer layers improved the electron mobility of 2-dimensional electron gas and allowed us to grow a GaN channel with a low carbon concentration. Furthermore, a regrown n-GaN contact layer was employed to minimize source/drain contact resistances. A high drain current of 1470 mA/mm and high breakdown voltage of 258 V were achieved. Our results demonstrate the potential of GaN HEMTs on the AlN substrate as next-generation high-power radio frequency devices.
- 9 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 11, 101-106
Open Access24.4 W/mm X-Band GaN HEMTs on AlN Substrates With the LPCVD-Grown High-Breakdown-Field SiN x Layer
This paper reports on an AlGaN/GaN high-electron-mobility transistor (HEMT) on free-standing AlN substrates with a record-high output power density of 24.4 W/mm at the X-band. A high-drain current operation of 1.4 A/mm was realized by employing high-density 2-dimensional electron gas channel and regrown Ohmic contacts. Furthermore, a high-voltage operation of 110 V was achieved owing to the high-density and high-breakdown SiNx layer grown by low-pressure/high-temperature chemical vapor deposition. Three-stage AlGaN buffer layers improved the electron mobility of 2-dimensional electron gas and allowed us to grow a GaN channel with a low carbon concentration. Furthermore, a regrown n-GaN contact layer was employed to minimize source/drain contact resistances. A high drain current of 1470 mA/mm and high breakdown voltage of 258 V were achieved. Our results demonstrate the potential of GaN HEMTs on the AlN substrate as next-generation high-power radio frequency devices.
- 29 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 11 (11) , 1909-1916
Thermal Design of GaN-on-GaN HEMT Power Amplifier for a Selective Heating Microwave Oven
In this study, we investigated the heat dissipation characteristics of gallium nitride (GaN) high-electron mobility transistors (HEMTs) fabricated on a freestanding GaN substrate (GaN-on-GaN HEMTs) by simulation. Although the GaN substrate has a lower thermal conductivity than the conventional silicon carbide (SiC) substrate, it was demonstrated that the GaN-on-GaN HEMT has a thermal resistance comparable to the conventional GaN-on-SiC HEMT in a simulated structure composed of a 100- $\mu \text{m}$ -thick substrate and a 2- $\mu \text{m}$ -thick GaN epitaxial layer. This is because GaN-on-GaN has a higher thermal conductivity of the GaN epitaxial layer and a lower thermal boundary resistance than GaN-on-SiC. Next, the thermal design of a 400-W/eight-channel selective heating microwave oven, which consists of eight pairs of patch antennas and power amplifier (PA) modules, involving a 50-W-class GaN-on-GaN HEMT PA, a driving amplifier, an oscillator, and several circuits, was carried out. The fan and fin specifications and enclosure configuration have been optimized to keep the temperature of the metal base on which the PA modules are mounted below 40 °C during full operation. Excellent agreement between the oven thermal simulation and the prototype thermocouple measurements was confirmed for the temperature difference between the metal base and the ambient. Finally, device dimensions for reliable operation were determined by simulating the channel temperature of the GaN-on-GaN HEMT PA during microwave heating. To keep the maximum channel temperature below 200 °C, the simulated device layout with a unit gate width ( $W_{\mathrm {gu}}$ ) of 100– $300~\mu \text{m}$ and a gate-to-gate spacing ( $L_{\mathrm {gg}}$ ) of 30– $70~\mu \text{m}$ was acceptable at a drain efficiency ( $\eta _{\mathrm {D}}$ ) of 75%. However, appropriate $W_{\mathrm {gu}}$ and $L_{\mathrm {gg}}$ were found to be required with a $\eta _{\mathrm {D}}$ of 65%.
- 29 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 11 (11) , 1909-1916
Thermal Design of GaN-on-GaN HEMT Power Amplifier for a Selective Heating Microwave Oven
In this study, we investigated the heat dissipation characteristics of gallium nitride (GaN) high-electron mobility transistors (HEMTs) fabricated on a freestanding GaN substrate (GaN-on-GaN HEMTs) by simulation. Although the GaN substrate has a lower thermal conductivity than the conventional silicon carbide (SiC) substrate, it was demonstrated that the GaN-on-GaN HEMT has a thermal resistance comparable to the conventional GaN-on-SiC HEMT in a simulated structure composed of a 100- $\mu \text{m}$ -thick substrate and a 2- $\mu \text{m}$ -thick GaN epitaxial layer. This is because GaN-on-GaN has a higher thermal conductivity of the GaN epitaxial layer and a lower thermal boundary resistance than GaN-on-SiC. Next, the thermal design of a 400-W/eight-channel selective heating microwave oven, which consists of eight pairs of patch antennas and power amplifier (PA) modules, involving a 50-W-class GaN-on-GaN HEMT PA, a driving amplifier, an oscillator, and several circuits, was carried out. The fan and fin specifications and enclosure configuration have been optimized to keep the temperature of the metal base on which the PA modules are mounted below 40 °C during full operation. Excellent agreement between the oven thermal simulation and the prototype thermocouple measurements was confirmed for the temperature difference between the metal base and the ambient. Finally, device dimensions for reliable operation were determined by simulating the channel temperature of the GaN-on-GaN HEMT PA during microwave heating. To keep the maximum channel temperature below 200 °C, the simulated device layout with a unit gate width ( $W_{\mathrm {gu}}$ ) of 100– $300~\mu \text{m}$ and a gate-to-gate spacing ( $L_{\mathrm {gg}}$ ) of 30– $70~\mu \text{m}$ was acceptable at a drain efficiency ( $\eta _{\mathrm {D}}$ ) of 75%. However, appropriate $W_{\mathrm {gu}}$ and $L_{\mathrm {gg}}$ were found to be required with a $\eta _{\mathrm {D}}$ of 65%.
- 8 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (3) , 1675-1683
A 0.6–2.1-GHz Wideband GaN High-Power Amplifier Using Transmission-Line-Transformer-Based Differential-Mode Combiner With Second-Harmonic Suppression
A wideband gallium nitride (GaN) power amplifier (PA) using a four-way planar differential-mode combiner (DMC) with impedance transformation function based on the transmission line transformer (TLT) technique was fabricated. The performance was compared with a PA using a four-way planar common-mode combiner (CMC), which was recently reported. The fabricated PA with the CMC exhibited an average output power (Pout) of 233 W and an average power-added efficiency (PAE) of 42% in the frequency range of 0.5-2.1 GHz. The fabricated PA with DMC exhibited an average Pout of 282 W and an average PAE of 48% in the frequency range of 0.6-2.1 GHz, which is superior to the PA with CMC. Moreover, the fabricated PA with DMC exhibited a large second-harmonic suppression. The maximum suppression is -54 dBc at 1.5 GHz, and the average of the suppression from 0.6 to 2.1 GHz is -38.3 dBc.
- 8 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (3) , 1675-1683
A 0.6–2.1-GHz Wideband GaN High-Power Amplifier Using Transmission-Line-Transformer-Based Differential-Mode Combiner With Second-Harmonic Suppression
A wideband gallium nitride (GaN) power amplifier (PA) using a four-way planar differential-mode combiner (DMC) with impedance transformation function based on the transmission line transformer (TLT) technique was fabricated. The performance was compared with a PA using a four-way planar common-mode combiner (CMC), which was recently reported. The fabricated PA with the CMC exhibited an average output power (Pout) of 233 W and an average power-added efficiency (PAE) of 42% in the frequency range of 0.5-2.1 GHz. The fabricated PA with DMC exhibited an average Pout of 282 W and an average PAE of 48% in the frequency range of 0.6-2.1 GHz, which is superior to the PA with CMC. Moreover, the fabricated PA with DMC exhibited a large second-harmonic suppression. The maximum suppression is -54 dBc at 1.5 GHz, and the average of the suppression from 0.6 to 2.1 GHz is -38.3 dBc.
- Open Access
- 6 February 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (SG) , SGGH03
Achieving a high breakdown voltage for GaAsSb-based backward diodes using the carrier depletion effect originating from nanowires
The forward breakdown voltage (BV) of GaAsSb-based backward diodes was significantly increased by using nanowire structures. From the structure analysis of the fabricated devices, it was found that the sidewall of the nanowires was completely covered with thin AlO x film and that the top part of the nanowire sidewalls also contains electrode materials. From device simulations, we found that the increased BV originated from the carrier depletion brought by the metal–semiconductor–insulator structure at the top of the nanowires. In addition, this effect strongly depends on the diameters and doping levels of the nanowire. The increased BV achieved with this effect will increase the dynamic range of rectification.
- 6 February 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (SG) , SGGH03
Open AccessAchieving a high breakdown voltage for GaAsSb-based backward diodes using the carrier depletion effect originating from nanowires
The forward breakdown voltage (BV) of GaAsSb-based backward diodes was significantly increased by using nanowire structures. From the structure analysis of the fabricated devices, it was found that the sidewall of the nanowires was completely covered with thin AlO x film and that the top part of the nanowire sidewalls also contains electrode materials. From device simulations, we found that the increased BV originated from the carrier depletion brought by the metal–semiconductor–insulator structure at the top of the nanowires. In addition, this effect strongly depends on the diameters and doping levels of the nanowire. The increased BV achieved with this effect will increase the dynamic range of rectification.
- 13 January 2017
- Published by IOP Publishing in Applied Physics Express
- Vol. 10 (2) , 024102
Maximum frequency of oscillation of 1.3 THz obtained by using an extended drain-side recess structure in 75-nm-gate InAlAs/InGaAs high-electron-mobility transistors
- 13 January 2017
- Published by IOP Publishing in Applied Physics Express
- Vol. 10 (2) , 024102
Maximum frequency of oscillation of 1.3 THz obtained by using an extended drain-side recess structure in 75-nm-gate InAlAs/InGaAs high-electron-mobility transistors
- 1 October 2010
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 49 (10R) , 104101
Energy Band Control of GaAsSb-Based Backward Diodes to Improve Sensitivity of Millimeter-Wave Detection
The effect of energy band control with varying carrier concentration in GaAsSb-based backward diodes was investigated and diode parameters were analyzed to enhance voltage sensitivity. The backward diodes consisted of a heterojunction of p-GaAs0.51Sb0.49/i-In0.52Al0.48As/n-In0.63Ga0.37As/n-In0.53Ga0.47As, and they were mostly lattice-matched to an InP substrate. The degree of energy band bending at the depletion layer in n-In0.63Ga0.37As was varied on the basis of the carrier concentration in the n-In0.53Ga0.47As band control layer. Voltage sensitivity depends on carrier concentration since the concentration affects the band bending structure at the junction. The parameter analysis indicated that junction capacitance decreased when the carrier concentration in the band control layer decreased. When the carrier concentration in the band control layer was as low as 5×1018 cm-3, with the diode mesa at a diameter of 2.0 µm, an unmatched voltage sensitivity of 1495 V/W was obtained.
- 1 October 2010
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 49 (10R) , 104101
Energy Band Control of GaAsSb-Based Backward Diodes to Improve Sensitivity of Millimeter-Wave Detection
The effect of energy band control with varying carrier concentration in GaAsSb-based backward diodes was investigated and diode parameters were analyzed to enhance voltage sensitivity. The backward diodes consisted of a heterojunction of p-GaAs0.51Sb0.49/i-In0.52Al0.48As/n-In0.63Ga0.37As/n-In0.53Ga0.47As, and they were mostly lattice-matched to an InP substrate. The degree of energy band bending at the depletion layer in n-In0.63Ga0.37As was varied on the basis of the carrier concentration in the n-In0.53Ga0.47As band control layer. Voltage sensitivity depends on carrier concentration since the concentration affects the band bending structure at the junction. The parameter analysis indicated that junction capacitance decreased when the carrier concentration in the band control layer decreased. When the carrier concentration in the band control layer was as low as 5×1018 cm-3, with the diode mesa at a diameter of 2.0 µm, an unmatched voltage sensitivity of 1495 V/W was obtained.
- 1 January 2008
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 47 (1S) , 620
Application of Extremely Thin ZrN Film as Diffusion Barrier between Cu and SiOC
- 1 January 2008
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 47 (1S) , 620
Application of Extremely Thin ZrN Film as Diffusion Barrier between Cu and SiOC
- 27 May 2005
- Published by Springer Nature in Polymer Bulletin
- Vol. 54 (4-5) , 237-242
Synthesis and properties of novel vinyl polymers bearing azacrown ether side chain
- 27 May 2005
- Published by Springer Nature in Polymer Bulletin
- Vol. 54 (4-5) , 237-242
Synthesis and properties of novel vinyl polymers bearing azacrown ether side chain