Cleber Luis Pedroso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Cleber Luis Pedroso has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Rodrigo Eduardo Catai
Universidade Tecnológica Federal do Paraná (UTFPR), Graduate Program in Urban Environmental Sustainability (PPGSAU-CT), Curitiba, Brazil
2 shared publications - Vsevolod Mymrin
Federal University of Technology, Curitiba, Brazil
2 shared publications - Alfredo Iarozinski Neto
Universidade Tecnológica Federal do Paraná
1 shared publication - Charles Windson Isidoro Haminiuk
Universidade Tecnológica Federal do Paraná
1 shared publication Daniela E. Evaniki
1 shared publication- Daniela Evaniki Pedroso
University Tuiuti of Paraná, Curitiba, PR
1 shared publication
Latest Publications
- 28 January 2023
- Published by Magnus Med Club LLC - USA in Catalysis Research
- Vol. 3 (1) , 1
Hazardous Bauxite Red Mud and Ferrous Slag Management to Produce Sustainable Construction Materials
INTRODUCTION In one of his interviews, the most celebrated modern-day cosmologist, [1] said that “pollution and human “stupidity” remained the greatest threats to humankind.” He claimed that air pollution had increased 8% within the last five years, and the authors of this paper are convinced that most of that is due to municipal and industrial wastes. According to the authors of this article, the best strategic way to prevent or postpone as much as possible this global ecological tragedy, scientifically predicted by Hawking, is to replace the raw materials with industrial waste. Hawking calculated that, at the current pace, the temperature of the atmosphere would rise, leading to the death of humankind in the next 300 years. It is known that the most significant air pollutants come from industrial and municipal waste dumps. From this, it follows that scientifically based waste disposal will be a crucial factor for the survival of humanity.
- 28 January 2023
- Published by Magnus Med Club LLC - USA in Catalysis Research
- Vol. 3 (1) , 1
Hazardous Bauxite Red Mud and Ferrous Slag Management to Produce Sustainable Construction Materials
INTRODUCTION In one of his interviews, the most celebrated modern-day cosmologist, [1] said that “pollution and human “stupidity” remained the greatest threats to humankind.” He claimed that air pollution had increased 8% within the last five years, and the authors of this paper are convinced that most of that is due to municipal and industrial wastes. According to the authors of this article, the best strategic way to prevent or postpone as much as possible this global ecological tragedy, scientifically predicted by Hawking, is to replace the raw materials with industrial waste. Hawking calculated that, at the current pace, the temperature of the atmosphere would rise, leading to the death of humankind in the next 300 years. It is known that the most significant air pollutants come from industrial and municipal waste dumps. From this, it follows that scientifically based waste disposal will be a crucial factor for the survival of humanity.
- Open Access
- 4 December 2020
- Published by Universidade Federal de Santa Maria in Revista Eletrônica em Gestão, Educação e Tecnologia Ambiental
- Vol. 24, e6
New composites from waste: iron ore, pulp, lime, and concrete
This research aimed at the development of new composites for civil construction using only industrial waste, namely, iron ore tailings (IOT), pulp production waste (PPW), lime production waste (LPW), and concrete waste (CW). The characterization of raw materials was carried out through particle size, specific mass, hydrogen potential (pH), loss on ignition (LOI) tests, and scanning electron microscopy (SEM); and, it was analyzed axial compression resistance and SEM in the developed composites. The specimens for the resistance test were molded, always using the same four types of residues in the mixture, with only water addition and no other type of binder. The residues proportions used were, in percentage, 10% to 40% of IOT and PPW, 25 to 30% of the LPW, and 15% to 25% of CW, distributed in 19 different compositions, that is, the proportions' variation of the residues in each specimen. The specimens were tested at the ages of 3, 7, 14, 28, 60, 90, 180, 365, and 720 days of cure. The results indicated a slight increase in resistance with increasing curing time, with emphasis on compositions 16 and 17, whose 28-day axial compression resistance reached 4.07MPa and 6.92MPa, respectively. In these two compositions (16 and 17), the formation of new structures was observed in the materials due to the neutralization and dissolution of the surfaces, as the alkalinity gradually decreased over time, with the hydrogen potential (pH) around 7.50 that, consequently caused the synthesis of new amorphous and crystalline formations. In this context, the studies allowed to conclude that the association of industrial residues has potential use as civil construction materials, for instance, in concrete artifacts, besides contributing to the reduction of finite natural resources extraction. It also provides a correct destination for the waste disposed of inappropriately, that constantly menaces the environment and the society that lives around it.
- 4 December 2020
- Published by Universidade Federal de Santa Maria in Revista Eletrônica em Gestão, Educação e Tecnologia Ambiental
- Vol. 24, e6
Open AccessNew composites from waste: iron ore, pulp, lime, and concrete
This research aimed at the development of new composites for civil construction using only industrial waste, namely, iron ore tailings (IOT), pulp production waste (PPW), lime production waste (LPW), and concrete waste (CW). The characterization of raw materials was carried out through particle size, specific mass, hydrogen potential (pH), loss on ignition (LOI) tests, and scanning electron microscopy (SEM); and, it was analyzed axial compression resistance and SEM in the developed composites. The specimens for the resistance test were molded, always using the same four types of residues in the mixture, with only water addition and no other type of binder. The residues proportions used were, in percentage, 10% to 40% of IOT and PPW, 25 to 30% of the LPW, and 15% to 25% of CW, distributed in 19 different compositions, that is, the proportions' variation of the residues in each specimen. The specimens were tested at the ages of 3, 7, 14, 28, 60, 90, 180, 365, and 720 days of cure. The results indicated a slight increase in resistance with increasing curing time, with emphasis on compositions 16 and 17, whose 28-day axial compression resistance reached 4.07MPa and 6.92MPa, respectively. In these two compositions (16 and 17), the formation of new structures was observed in the materials due to the neutralization and dissolution of the surfaces, as the alkalinity gradually decreased over time, with the hydrogen potential (pH) around 7.50 that, consequently caused the synthesis of new amorphous and crystalline formations. In this context, the studies allowed to conclude that the association of industrial residues has potential use as civil construction materials, for instance, in concrete artifacts, besides contributing to the reduction of finite natural resources extraction. It also provides a correct destination for the waste disposed of inappropriately, that constantly menaces the environment and the society that lives around it.