Zuzhong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zuzhong Li has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Rui He
School of Materials Science and Engineering, Chang’an University, Xi’an 710064, China
2 shared publications Yuan Li
Research Institute of Dushanzi Petrochemical Branch Co., CNPC, Karamay, China
2 shared publicationsZepeng Zhao
Research Institute of Dushanzi Petrochemical Branch Co., CNPC, Karamay, China
2 shared publicationsChunguang Fa
School of Materials Science and Engineering, Chang’an University, Xi’an 710061, China
1 shared publication- Dewen Su
School of Materials Science and Engineering, Chang’an University, Xi’an 710064, China
1 shared publication - Fan Li
School of Materials Science and Engineering, Chang’an University, Xi’an 710064, China
1 shared publication
Latest Publications
- Open Access
Preparation Method of Waterborne Epoxy and the Properties of Its Modified Emulsified Asphalt
Micro-surfacing is considered as an effective and economical preventive maintenance technique for asphalt pavement. Its performance largely depends on the material compositions of emulsified asphalt binders. To overcome the deficiencies of ordinary micro-surfacing, waterborne epoxy resin emulsified asphalt (WEREA) micro-surfacing can significantly enhance its pavement performance. This work investigated the preparation of waterborne epoxy resin emulsion (WER), solidification behavior, and rheological properties of the solidified WEREA (S-WEREA) by phase inversion method, viscosity, fluorescence microscopy (FM), Fourier-transform infrared (FTIR), and dynamic shear rheometer (DSR) tests, respectively. The results indicated that the optimal preparation conditions of WER were determined as SDS:Span-80 = 5:13 (HLB value 14.2), a 12% emulsifier dosage, a 4712 s−1 shear rate, and a 60 °C preparation temperature, based on the evaluation of laser particle size for all specimens. The viscosity, FM, and FTIR tests exhibited that a strong chemical reaction occurred between epoxy resin and curing agent to form abundant crosslinked structures and new functional groups, contributing to improving the high temperature stability of S-WEREA. Dynamic shear rheometer (DSR) tests, including frequency sweep, multiple stress creep and recovery (MSCR), and linear amplitude sweep (LAS), indicated that a 15% WER content could balance the high-temperature deformation resistance and anti-fatigue performance, while excessive WER could adversely affect the low-temperature performance of S-WEREA and also lead to macroscopic phase separation at high-temperature. This study is expected to lay an experimental foundation for the wide application of WEREA in micro-surfacing.
Open AccessPreparation Method of Waterborne Epoxy and the Properties of Its Modified Emulsified Asphalt
Micro-surfacing is considered as an effective and economical preventive maintenance technique for asphalt pavement. Its performance largely depends on the material compositions of emulsified asphalt binders. To overcome the deficiencies of ordinary micro-surfacing, waterborne epoxy resin emulsified asphalt (WEREA) micro-surfacing can significantly enhance its pavement performance. This work investigated the preparation of waterborne epoxy resin emulsion (WER), solidification behavior, and rheological properties of the solidified WEREA (S-WEREA) by phase inversion method, viscosity, fluorescence microscopy (FM), Fourier-transform infrared (FTIR), and dynamic shear rheometer (DSR) tests, respectively. The results indicated that the optimal preparation conditions of WER were determined as SDS:Span-80 = 5:13 (HLB value 14.2), a 12% emulsifier dosage, a 4712 s−1 shear rate, and a 60 °C preparation temperature, based on the evaluation of laser particle size for all specimens. The viscosity, FM, and FTIR tests exhibited that a strong chemical reaction occurred between epoxy resin and curing agent to form abundant crosslinked structures and new functional groups, contributing to improving the high temperature stability of S-WEREA. Dynamic shear rheometer (DSR) tests, including frequency sweep, multiple stress creep and recovery (MSCR), and linear amplitude sweep (LAS), indicated that a 15% WER content could balance the high-temperature deformation resistance and anti-fatigue performance, while excessive WER could adversely affect the low-temperature performance of S-WEREA and also lead to macroscopic phase separation at high-temperature. This study is expected to lay an experimental foundation for the wide application of WEREA in micro-surfacing.
- Open Access
Investigation of the Properties of High-Viscosity Modified Asphalt Binder under Hygrothermal Environments
High-viscosity modified asphalt binder (HVMA) is used widely as a polymer-modified binder in porous asphalt pavement because it can improve the cohesiveness of the asphalt mixture. However, because of the high voidage in the mixture, HVMA is vulnerable to aging induced by temperature, oxygen, water, sunlight, and other climatic conditions, which degrades the performance of pavement. The properties of asphalt binder are affected adversely by the effects of hygrothermal environments in megathermal and rainy areas. Therefore, it is essential to study the aging characteristics of HVMA under the influence of hygrothermal environments to promote its application as a high-viscosity modifier. A hygrothermal cycle aging test (HCAT) was designed to simulate the aging of HVMA when rainwater was kept inside of the pavement after rainfall in megathermal areas. One kind of base bitumen and three kinds of HVMA (referred to as SBS, A, and B, respectively) were selected in this study. Short-term aging tests, hygrothermal cycling aging tests, and long-term aging tests were performed on the base bitumen and three kinds of modified asphalt binder. Fourier-transform infrared spectroscopy (FTIR), thermo-gravimetric analysis (TGA), and dynamic shear rheological (DSR) tests were used to evaluate the properties of the binders on the micro and macro scales. By comparing the index variations of the four binders before and after aging, the effects of the hygrothermal environment on the properties of HVMA were studied. It was found that the effects of the hygrothermal environment expedited the decomposition of the polymer and the formation of carbonyl groups compared with the TFOT and PAV test, which TGA confirmed further. Moreover, the thermal stability of the samples was improved after HCAT. In addition, the master curves of the complex modulus showed that hygrothermal cycles made the high-temperature rutting resistance of asphalt binder increase significantly. All of the results above verified that the effect of hygrothermal cycling could accelerate the aging of HVMA and shorten its service life.
Open AccessInvestigation of the Properties of High-Viscosity Modified Asphalt Binder under Hygrothermal Environments
High-viscosity modified asphalt binder (HVMA) is used widely as a polymer-modified binder in porous asphalt pavement because it can improve the cohesiveness of the asphalt mixture. However, because of the high voidage in the mixture, HVMA is vulnerable to aging induced by temperature, oxygen, water, sunlight, and other climatic conditions, which degrades the performance of pavement. The properties of asphalt binder are affected adversely by the effects of hygrothermal environments in megathermal and rainy areas. Therefore, it is essential to study the aging characteristics of HVMA under the influence of hygrothermal environments to promote its application as a high-viscosity modifier. A hygrothermal cycle aging test (HCAT) was designed to simulate the aging of HVMA when rainwater was kept inside of the pavement after rainfall in megathermal areas. One kind of base bitumen and three kinds of HVMA (referred to as SBS, A, and B, respectively) were selected in this study. Short-term aging tests, hygrothermal cycling aging tests, and long-term aging tests were performed on the base bitumen and three kinds of modified asphalt binder. Fourier-transform infrared spectroscopy (FTIR), thermo-gravimetric analysis (TGA), and dynamic shear rheological (DSR) tests were used to evaluate the properties of the binders on the micro and macro scales. By comparing the index variations of the four binders before and after aging, the effects of the hygrothermal environment on the properties of HVMA were studied. It was found that the effects of the hygrothermal environment expedited the decomposition of the polymer and the formation of carbonyl groups compared with the TFOT and PAV test, which TGA confirmed further. Moreover, the thermal stability of the samples was improved after HCAT. In addition, the master curves of the complex modulus showed that hygrothermal cycles made the high-temperature rutting resistance of asphalt binder increase significantly. All of the results above verified that the effect of hygrothermal cycling could accelerate the aging of HVMA and shorten its service life.
- Open Access
Effect of Alkali and Sulfate on the Hydration Characteristic of Cement-Based Materials Containing Coal Gasification Slag
Coal gasification slag is an inevitable by-product of the coal gasification process. This paper explored the feasibility of using activators (calcium hydroxide, sodium hydroxide, calcium sulfate, sodium sulfate) to promote the pozzolanic activity of milled coal gasification coarse slags (MCS), and analyzed the effect of alkali and sulfate activators on the hydration characteristic of cement-based materials containing MCS. Coal gasification slags with ignition lossses more than 15% were removed and the remaining slags were considered as cementitious material after milling. Scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA) and hydration heat tests were employed to analyze the hydration mechanism of the samples. Besides, the compressive strength values of cement mortars with MCS and activators were evaluated. The results showed that calcium hydroxide was conductive to the formation of hydration products and its crystallization could contribute to the strength improvement of the sample. Calcium sulfate mainly participated in the hydration process of cement to form ettringite (AFt) phases. Sodium hydroxide could accelerate the dissolution of active mineral phases of MCS, resulting in the pozzolanic activity being enhanced. Moreover, sodium sulfate could not only increase the formation of AFt phases, but also improved the alkalinity in sample to facilitate the production of gels. Among them, a better promotion effect could be obtained from the combined application of calcium hydroxide and sodium sulfate. In addition, the compressive strength values of cement mortars containing MCS tended to increase when activators were used. The sample activated by calcium hydroxide and sodium sulfate exhibited the highest strength, increasing by 18.55% at 28 days compared with the sample without an activator.
Open AccessEffect of Alkali and Sulfate on the Hydration Characteristic of Cement-Based Materials Containing Coal Gasification Slag
Coal gasification slag is an inevitable by-product of the coal gasification process. This paper explored the feasibility of using activators (calcium hydroxide, sodium hydroxide, calcium sulfate, sodium sulfate) to promote the pozzolanic activity of milled coal gasification coarse slags (MCS), and analyzed the effect of alkali and sulfate activators on the hydration characteristic of cement-based materials containing MCS. Coal gasification slags with ignition lossses more than 15% were removed and the remaining slags were considered as cementitious material after milling. Scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA) and hydration heat tests were employed to analyze the hydration mechanism of the samples. Besides, the compressive strength values of cement mortars with MCS and activators were evaluated. The results showed that calcium hydroxide was conductive to the formation of hydration products and its crystallization could contribute to the strength improvement of the sample. Calcium sulfate mainly participated in the hydration process of cement to form ettringite (AFt) phases. Sodium hydroxide could accelerate the dissolution of active mineral phases of MCS, resulting in the pozzolanic activity being enhanced. Moreover, sodium sulfate could not only increase the formation of AFt phases, but also improved the alkalinity in sample to facilitate the production of gels. Among them, a better promotion effect could be obtained from the combined application of calcium hydroxide and sodium sulfate. In addition, the compressive strength values of cement mortars containing MCS tended to increase when activators were used. The sample activated by calcium hydroxide and sodium sulfate exhibited the highest strength, increasing by 18.55% at 28 days compared with the sample without an activator.
- 13 July 2022
- Published by Springer Nature in Materials and Structures
- Vol. 55 (6) , 1-20
Effect of bitumen composition on micro-structure and rheological properties of styrene–butadiene–styrene modified asphalt before and after aging
- 13 July 2022
- Published by Springer Nature in Materials and Structures
- Vol. 55 (6) , 1-20
Effect of bitumen composition on micro-structure and rheological properties of styrene–butadiene–styrene modified asphalt before and after aging
- 15 January 2022
- Published by Springer Nature in Materials and Structures
- Vol. 55 (1) , 1-17
Influence of residual SB di-block in SBS on the thermo–oxidative aging behaviors of SBS and SBS modified asphalt
- 15 January 2022
- Published by Springer Nature in Materials and Structures
- Vol. 55 (1) , 1-17
Influence of residual SB di-block in SBS on the thermo–oxidative aging behaviors of SBS and SBS modified asphalt
- Open Access
- 1 January 2022
- Published by Wiley in Advances in Civil Engineering
- Vol. 2022 (1)
Characteristic Evolution of GO/SBS‐Modified Asphalt during Aging
Styrene‐butadiene‐styrene (SBS)‐modified asphalt has been widely used in high‐grade pavement due to its excellent road performance. However, environmental factors will lead to continuous deterioration of SBS‐modified asphalt; thus, it is difficult for asphalt pavement to meet the demands of long‐term service. In recent years, graphene oxide (GO) has attracted the attention of scholars due to its excellent compatibility and modification effect when used as an asphalt modifier. Based on previous studies, this study explored the characteristic evolution of GO/SBS composite‐modified asphalt during aging. To achieve this goal, GO and the SBS polymer were blended to prepare GO/SBS composite, which was then used to prepare the modified asphalt. Pure SBS and the GO/SBS composite were investigated by gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), and thermogravimetry (TG). In addition, the GO/SBS‐modified asphalt and SBS‐modified asphalt were studied by FTIR, fluorescence microscope (FM), dynamic shear oscillatory (DSR) test, and multiple‐stress creep recovery (MSCR) test. The results indicated that the incorporation of GO inhibited the deterioration of the asphalt binder and relieved the degradation of the SBS modifier during the thermo‐oxidative aging and photo‐oxidative aging processes. Based on the results extracted from the curves of the original samples in the FTIR analysis, it was concluded that GO was combined by physical blending in SBS and SBS‐modified asphalt. The TG test results verified that the GO powder could ameliorate the thermal stability of SBS. Moreover, GO improved the antirutting performance of the original SBS‐modified asphalt, while the GO/SBS‐modified asphalt had relatively poorer antirutting performance compared to the SBS‐modified asphalt after the same aging tests. The reason was that the increment of antirutting performance of asphalt binder by aging process was inhibited by GO.
- 1 January 2022
- Published by Wiley in Advances in Civil Engineering
- Vol. 2022 (1)
Open AccessCharacteristic Evolution of GO/SBS‐Modified Asphalt during Aging
Styrene‐butadiene‐styrene (SBS)‐modified asphalt has been widely used in high‐grade pavement due to its excellent road performance. However, environmental factors will lead to continuous deterioration of SBS‐modified asphalt; thus, it is difficult for asphalt pavement to meet the demands of long‐term service. In recent years, graphene oxide (GO) has attracted the attention of scholars due to its excellent compatibility and modification effect when used as an asphalt modifier. Based on previous studies, this study explored the characteristic evolution of GO/SBS composite‐modified asphalt during aging. To achieve this goal, GO and the SBS polymer were blended to prepare GO/SBS composite, which was then used to prepare the modified asphalt. Pure SBS and the GO/SBS composite were investigated by gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), and thermogravimetry (TG). In addition, the GO/SBS‐modified asphalt and SBS‐modified asphalt were studied by FTIR, fluorescence microscope (FM), dynamic shear oscillatory (DSR) test, and multiple‐stress creep recovery (MSCR) test. The results indicated that the incorporation of GO inhibited the deterioration of the asphalt binder and relieved the degradation of the SBS modifier during the thermo‐oxidative aging and photo‐oxidative aging processes. Based on the results extracted from the curves of the original samples in the FTIR analysis, it was concluded that GO was combined by physical blending in SBS and SBS‐modified asphalt. The TG test results verified that the GO powder could ameliorate the thermal stability of SBS. Moreover, GO improved the antirutting performance of the original SBS‐modified asphalt, while the GO/SBS‐modified asphalt had relatively poorer antirutting performance compared to the SBS‐modified asphalt after the same aging tests. The reason was that the increment of antirutting performance of asphalt binder by aging process was inhibited by GO.
- Open Access
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Investigation on the Temperature Distribution of Asphalt Overlay on the Existing Cement Concrete Pavement in Hot‐Humid Climate in Southern China
Temperature is known to be one of the most important factors affecting the design and performance of asphalt concrete pavement. The distresses of asphalt overlay are closely related to its temperature, particularly in Guangxi, a hot‐humid‐climate region in China. This research is to analyze the impact of meteorological factors on temperature at 2 cm depth in asphalt overlay by ReliefF algorithm and also obtain the temperature prediction model using MATLAB. Two test sites were installed to monitor the temperatures at different pavement depths from 2014 to 2016; meanwhile, the meteorological data (including air temperature, solar radiation, wind speed, and relative humidity) were collected from the two meteorological stations. It has been found that the temperature at 2 cm depth experiences greater temperature variation, and the maximum and minimum temperatures of asphalt overlay, respectively, occur at 2 cm depth and on the surface. Besides, the results of ReliefF algorithm have also shown that the temperature at 2 cm depth is affected significantly by solar radiation, air temperature, wind speed, and the relative humidity. Based on these analyses, the prediction model of maximum temperature at 2 cm depth is developed using statistical regression. Moreover, the data collected in 2017 are used to validate the accuracy of the model. Compared with the existing models, the developed model was confirmed to be more effective for temperature prediction in hot‐humid region. In addition, the analysis of rutting depth and overlay deformation for the two test sections with different materials is done, and the results have shown that reasonable structure and materials of asphalt overlay are vital to promote the high‐temperature antideforming capability of pavement.
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Open AccessInvestigation on the Temperature Distribution of Asphalt Overlay on the Existing Cement Concrete Pavement in Hot‐Humid Climate in Southern China
Temperature is known to be one of the most important factors affecting the design and performance of asphalt concrete pavement. The distresses of asphalt overlay are closely related to its temperature, particularly in Guangxi, a hot‐humid‐climate region in China. This research is to analyze the impact of meteorological factors on temperature at 2 cm depth in asphalt overlay by ReliefF algorithm and also obtain the temperature prediction model using MATLAB. Two test sites were installed to monitor the temperatures at different pavement depths from 2014 to 2016; meanwhile, the meteorological data (including air temperature, solar radiation, wind speed, and relative humidity) were collected from the two meteorological stations. It has been found that the temperature at 2 cm depth experiences greater temperature variation, and the maximum and minimum temperatures of asphalt overlay, respectively, occur at 2 cm depth and on the surface. Besides, the results of ReliefF algorithm have also shown that the temperature at 2 cm depth is affected significantly by solar radiation, air temperature, wind speed, and the relative humidity. Based on these analyses, the prediction model of maximum temperature at 2 cm depth is developed using statistical regression. Moreover, the data collected in 2017 are used to validate the accuracy of the model. Compared with the existing models, the developed model was confirmed to be more effective for temperature prediction in hot‐humid region. In addition, the analysis of rutting depth and overlay deformation for the two test sections with different materials is done, and the results have shown that reasonable structure and materials of asphalt overlay are vital to promote the high‐temperature antideforming capability of pavement.
- 13 July 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 1390-1395
Fatigue Test of Composite Pavement on Stress Absorbing Layers for Reflective Cracking
To study the problem of reflective cracking in the composite pavement, the dynamic extension fatigue test device of the asphalt pavement for reflective cracking was developed. The large proportion size anti-cracking fatigue experiment was carried out to test the anti-cracking performance of the stress absorbing layers and to observe the expansion of reflective cracking, which can provide the important experimental data to determine the reasonable thickness of the stress absorbing layers. The results indicated that because of the stress absorbing layers established between Portland cement concrete base and asphalt pavement, the stress concentration in the cracks is reduced significantly, the reflective cracking propagation path is changed, and the service quality of the composite pavement is improved effectively; In order to compare the anti-cracking property of different pavement structures, the anti-cracking ratio R is proposed as the evaluation index. According to the test results and the material properties of the stress absorbing layers, the reasonable thickness of the stress absorbing layers is 2∼3 cm.
- 13 July 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 1390-1395
Fatigue Test of Composite Pavement on Stress Absorbing Layers for Reflective Cracking
To study the problem of reflective cracking in the composite pavement, the dynamic extension fatigue test device of the asphalt pavement for reflective cracking was developed. The large proportion size anti-cracking fatigue experiment was carried out to test the anti-cracking performance of the stress absorbing layers and to observe the expansion of reflective cracking, which can provide the important experimental data to determine the reasonable thickness of the stress absorbing layers. The results indicated that because of the stress absorbing layers established between Portland cement concrete base and asphalt pavement, the stress concentration in the cracks is reduced significantly, the reflective cracking propagation path is changed, and the service quality of the composite pavement is improved effectively; In order to compare the anti-cracking property of different pavement structures, the anti-cracking ratio R is proposed as the evaluation index. According to the test results and the material properties of the stress absorbing layers, the reasonable thickness of the stress absorbing layers is 2∼3 cm.