Tien-Jen Chang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tien-Jen Chang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Line Hagner Nielsen
Department of Health Technology, Technical University of Denmark, Ørsteds Plads 345C, 2800 Kgs. Lyngby, Denmark
3 shared publications - Anja Boisen
Technical University of Denmark
2 shared publications En-Te Hwu
The Danish National Research Foundation and Villum Foundation's Center for Intelligent Drug Delivery and Sensing Using Microcontainers and Nanomechanics (IDUN), Department of Health Technology, Technical University of Denmark, 2800 Kgs. Lyngby, Denmark
2 shared publicationsAnja Boisen
The Danish National Research Foundation and Villum Foundation's Center for Intelligent Drug Delivery and Sensing Using Microcontainers and Nanomechanics (IDUN), Department of Health Technology, Technical University of Denmark, 2800 Kgs. Lyngby, Denmark
1 shared publicationEduard Marzo Vila
The Danish National Research Foundation and Villum Foundation's Center for Intelligent Drug Delivery and Sensing Using Microcontainers and Nanomechanics (IDUN) Department of Health Technology Technical University of Denmark Kgs. Lyngby 2800 Denmark
1 shared publication- En-Te Hwu
Department of Health Technology, Technical University of Denmark, 2800 Lyngby, Denmark
1 shared publication
Latest Publications
- Open Access
- 4 December 2022
- Published by Wiley in Advanced Healthcare Materials
- Vol. 12 (4) , e2201897
3D‐Printed Radiopaque Microdevices with Enhanced Mucoadhesive Geometry for Oral Drug Delivery
During the past decades, microdevices have been evaluated as a means to overcome challenges within oral drug delivery, thus improving bioavailability. Fabrication of microdevices is often limited to planar or simple 3D designs. Therefore, this work explores how microscale stereolithography 3D printing can be used to fabricate radiopaque microcontainers with enhanced mucoadhesive geometries, which can enhance bioavailability by increasing gastrointestinal retention. Ex vivo force measurements suggest increased mucoadhesion of microcontainers with adhering features, such as pillars and arrows, compared to a neutral design. In vivo studies, utilizing planar X‐ray imaging, show the time‐dependent gastrointestinal location of microcontainers, whereas computed tomography scanning and cryogenic scanning electron microscopy reveal information about their spatial dynamics and mucosal interactions, respectively. For the first time, the effect of 3D microdevice modifications on gastrointestinal retention is traced in vivo, and the applied methods provide a much‐needed approach for investigating the impact of device design on gastrointestinal retention.
- 4 December 2022
- Published by Wiley in Advanced Healthcare Materials
- Vol. 12 (4) , e2201897
Open Access3D‐Printed Radiopaque Microdevices with Enhanced Mucoadhesive Geometry for Oral Drug Delivery
During the past decades, microdevices have been evaluated as a means to overcome challenges within oral drug delivery, thus improving bioavailability. Fabrication of microdevices is often limited to planar or simple 3D designs. Therefore, this work explores how microscale stereolithography 3D printing can be used to fabricate radiopaque microcontainers with enhanced mucoadhesive geometries, which can enhance bioavailability by increasing gastrointestinal retention. Ex vivo force measurements suggest increased mucoadhesion of microcontainers with adhering features, such as pillars and arrows, compared to a neutral design. In vivo studies, utilizing planar X‐ray imaging, show the time‐dependent gastrointestinal location of microcontainers, whereas computed tomography scanning and cryogenic scanning electron microscopy reveal information about their spatial dynamics and mucosal interactions, respectively. For the first time, the effect of 3D microdevice modifications on gastrointestinal retention is traced in vivo, and the applied methods provide a much‐needed approach for investigating the impact of device design on gastrointestinal retention.
- Open Access
- 11 February 2021
- Published by Springer Nature in Communications Physics
- Vol. 4 (1) , 1-8
Micro and nanoscale 3D printing using optical pickup unit from a gaming console
Conventional photopolymerization-based 3D printing still requires developing a concise and cost-effective method to improve the printing resolution at the nanoscale. Here, we propose the use of a gaming console optical drive pickup unit for 3D photopolymerization. This mass-produced optical pickup unit features a finely adjustable diode laser, allowing us to adjust the printing resolution from tens of micrometres down to hundreds of nanometres without requiring oxygen radical scavenging or costly femtosecond lasers. We evaluate the 3D printing performance using a commercial photopolymer under different laser exposure parameters. The proposed printing system achieves a resolution of 385 nm along the lateral direction and XYZ nano-resolution linear stages enable a printing volume of up to 50 × 50 × 25 mm3. Finally, we demonstrate the fabrication of 3D stereoscopic microstructures. The substantially simplified optics proposed here paves the way for affordable high-resolution micro/nanoscale 3D fabrication.
- 11 February 2021
- Published by Springer Nature in Communications Physics
- Vol. 4 (1) , 1-8
Open AccessMicro and nanoscale 3D printing using optical pickup unit from a gaming console
Conventional photopolymerization-based 3D printing still requires developing a concise and cost-effective method to improve the printing resolution at the nanoscale. Here, we propose the use of a gaming console optical drive pickup unit for 3D photopolymerization. This mass-produced optical pickup unit features a finely adjustable diode laser, allowing us to adjust the printing resolution from tens of micrometres down to hundreds of nanometres without requiring oxygen radical scavenging or costly femtosecond lasers. We evaluate the 3D printing performance using a commercial photopolymer under different laser exposure parameters. The proposed printing system achieves a resolution of 385 nm along the lateral direction and XYZ nano-resolution linear stages enable a printing volume of up to 50 × 50 × 25 mm3. Finally, we demonstrate the fabrication of 3D stereoscopic microstructures. The substantially simplified optics proposed here paves the way for affordable high-resolution micro/nanoscale 3D fabrication.