Teoman Tinçer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Teoman Tinçer has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
S. Çetin
Department of Chemistry, Middle East Technical University, Ankara 06531, Turkey
2 shared publicationsDeğer Şen
Division of Material Technologies Defense Industries Research and Development Institute Tubitak Sage PK: 16 06261 Ankara Turkey
1 shared publication- Gürkan Atınç Yılmaz
Division of Material Technologies Defense Industries Research and Development Institute Tubitak Sage PK: 16 06261 Ankara Turkey
1 shared publication Levent Toppare
Department of Chemistry , Middle East Technical University , Ankara, 06531, Turkey
1 shared publicationS. Tan
Department of Chemistry, Middle East Technical University, Ankara-TR-06531, Turkey
1 shared publicationSemra Tan
Department of Chemistry, Middle East Technical University, TR-06531 Ankara, Turkey
1 shared publication
Latest Publications
- 18 January 2016
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 133 (17)
Additives for ultraviolet‐induced oxidative degradation of low‐density polyethylene
Polyethylene (PE) is one of the most widely produced and widely used plastics in the world. Saturated hydrocarbons cannot absorb the energy of the light reaching earth, so the degradation process is rather slow; this, in return, causes disposal problems. On the other hand, it was observed that in the presence of oxygen and impurities in the polymer matrix, the degradation could be reduced to shorter time intervals. In this study, vanadium(III) acetyl acetonate (VAc), serpentine (SE), and Cloisite 30B (CL) were used as additives, both together and alone, and we followed the photodegradation of PE. The amount of VAc was kept constant at 0.2 wt %, whereas the amounts of SE and CL were varied between 1 and 4 wt %. The samples were irradiated by UV light for up to 500 h. Mechanical and spectroscopic measurements were carried out during certain time intervals to monitor the degradation. VAc containing PE showed the fastest degradation. The elongation at break values of these samples were reduced to half of the initial value of elongation at break within five days. Combinations of the CL and SE additives were also proven to accelerate the degradation of PE; this was followed by an increase in the carbonyl index, which was observed to be at least 10 times greater than that of pure PE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43354.
- 18 January 2016
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 133 (17)
Additives for ultraviolet‐induced oxidative degradation of low‐density polyethylene
Polyethylene (PE) is one of the most widely produced and widely used plastics in the world. Saturated hydrocarbons cannot absorb the energy of the light reaching earth, so the degradation process is rather slow; this, in return, causes disposal problems. On the other hand, it was observed that in the presence of oxygen and impurities in the polymer matrix, the degradation could be reduced to shorter time intervals. In this study, vanadium(III) acetyl acetonate (VAc), serpentine (SE), and Cloisite 30B (CL) were used as additives, both together and alone, and we followed the photodegradation of PE. The amount of VAc was kept constant at 0.2 wt %, whereas the amounts of SE and CL were varied between 1 and 4 wt %. The samples were irradiated by UV light for up to 500 h. Mechanical and spectroscopic measurements were carried out during certain time intervals to monitor the degradation. VAc containing PE showed the fastest degradation. The elongation at break values of these samples were reduced to half of the initial value of elongation at break within five days. Combinations of the CL and SE additives were also proven to accelerate the degradation of PE; this was followed by an increase in the carbonyl index, which was observed to be at least 10 times greater than that of pure PE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43354.
- 15 May 2014
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 131 (20)
Effect of inert plasticizers on mechanical, thermal, and sensitivity properties of polyurethane‐based plastic bonded explosives
Mechanical, thermal, and sensitivity properties of plastic bonded explosives (PBX) depend on the type of ingredients in their formulation. Aim of the work is to develop aluminized cast PBX formulations and process conditions by using alternative inert plasticizers to have similar or better properties than PBXN‐109 without compromising sensitivity properties. Although very small portion of total production of plasticizers is used for solid rocket propellant and explosive formulations, they play very significant role in that area. Both inert and energetic plasticizers have involved propellant and explosive formulations to improve process parameters, mechanical properties, and even insensitivity properties of them. Isodecyl pelargonate and dioctyl adipate are the most preferred inert plasticizers in polyurethane based thermoset propellant and explosive formulations. In addition to them, diisononyl adipate and diisononyl phthalate were used and screened as inert plasticizer candidates for aluminized cast PBX formulations. Mechanical, thermal, and sensitivity properties of PBX formulations were studied and compared in detail. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 40907.
- 15 May 2014
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 131 (20)
Effect of inert plasticizers on mechanical, thermal, and sensitivity properties of polyurethane‐based plastic bonded explosives
Mechanical, thermal, and sensitivity properties of plastic bonded explosives (PBX) depend on the type of ingredients in their formulation. Aim of the work is to develop aluminized cast PBX formulations and process conditions by using alternative inert plasticizers to have similar or better properties than PBXN‐109 without compromising sensitivity properties. Although very small portion of total production of plasticizers is used for solid rocket propellant and explosive formulations, they play very significant role in that area. Both inert and energetic plasticizers have involved propellant and explosive formulations to improve process parameters, mechanical properties, and even insensitivity properties of them. Isodecyl pelargonate and dioctyl adipate are the most preferred inert plasticizers in polyurethane based thermoset propellant and explosive formulations. In addition to them, diisononyl adipate and diisononyl phthalate were used and screened as inert plasticizer candidates for aluminized cast PBX formulations. Mechanical, thermal, and sensitivity properties of PBX formulations were studied and compared in detail. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 40907.
- 24 February 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 121 (2) , 846-854
Preparation and characterization of polypropylene/serpentine composites
- 24 February 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 121 (2) , 846-854
Preparation and characterization of polypropylene/serpentine composites
- 3 September 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 118 (5) , 3034-3040
Flammability and mechanical properties of Al(OH)3 and BaSO4 filled polypropylene
- 3 September 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 118 (5) , 3034-3040
Flammability and mechanical properties of Al(OH)3 and BaSO4 filled polypropylene
- 28 December 2007
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 108 (1) , 473-482
Thermal stability and decomposition mechanism of poly(p‐acryloyloxybenzoic acid and poly (p‐methacryloyloxybenzoic acid) and their graft copolymers with polypropylene, Part II
Thermal stability and decomposition mechanism of poly(p‐acryloyloxybenzoic) acid (PABA), p‐methacryloyloxybenzoic acid (PMBA), and their graft coproducts of PP were studied by differential scanning calorimetry, direct pyrolysis mass spectrometry, and TG/IR system, combined thermogravimetric analyzer, and FTIR spectrometer. The homopolymers and corresponding grafts were found to be stable in nitrogen atmosphere but started to decompose under atmospheric conditions when heated above 230°C. PABA and PAPA‐g‐PP showed a better thermal stability compared to the other polymer. The degradation proceeded predominantly by decomposition of side groups giving phenol, benzoic acid, hydroxybenzoic acid, carboxylic and carbonyl groups, and by decomposition of phenol into cyclodiene mainly. It was also seen that the degradation path did not greatly changed whether the PABA or PMBA were homopolymers or grafted onto PP but the induction temperature of grafted polymers was seen at some 10–20°C higher. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008
- 28 December 2007
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 108 (1) , 473-482
Thermal stability and decomposition mechanism of poly(p‐acryloyloxybenzoic acid and poly (p‐methacryloyloxybenzoic acid) and their graft copolymers with polypropylene, Part II
Thermal stability and decomposition mechanism of poly(p‐acryloyloxybenzoic) acid (PABA), p‐methacryloyloxybenzoic acid (PMBA), and their graft coproducts of PP were studied by differential scanning calorimetry, direct pyrolysis mass spectrometry, and TG/IR system, combined thermogravimetric analyzer, and FTIR spectrometer. The homopolymers and corresponding grafts were found to be stable in nitrogen atmosphere but started to decompose under atmospheric conditions when heated above 230°C. PABA and PAPA‐g‐PP showed a better thermal stability compared to the other polymer. The degradation proceeded predominantly by decomposition of side groups giving phenol, benzoic acid, hydroxybenzoic acid, carboxylic and carbonyl groups, and by decomposition of phenol into cyclodiene mainly. It was also seen that the degradation path did not greatly changed whether the PABA or PMBA were homopolymers or grafted onto PP but the induction temperature of grafted polymers was seen at some 10–20°C higher. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008
- 28 December 2007
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 108 (1) , 414-422
Graft copolymerization ofp-acryloyloxybenzoic acid andp-methacryloyloxybenzoic acid onto isotactic polypropylene and their thermal properties: Part I
- 28 December 2007
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 108 (1) , 414-422
Graft copolymerization ofp-acryloyloxybenzoic acid andp-methacryloyloxybenzoic acid onto isotactic polypropylene and their thermal properties: Part I
- 6 May 2003
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 89 (4) , 1039-1048
Melt blending of poly(ethylene terephthalate) with polypropylene in the presence of silane coupling agent
A silane coupling agent (SCA) was used as a compatibilizer for polypropylene–poly(ethylene teraphthalate) (PP–PET) blends with 20, 40, 50, and 60% PET compositions by weight. PP–PET mixtures were blended with and without an SCA by a single‐screw extruder. The effect of silane modification on the tensile and impact properties of the blends was investigated. The morphology and thermal behavior of the blends were examined with scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), respectively. The presence of the SCA used in this work extensively improved the mechanical properties of the blends. Mechanical properties were found to be highly dependent on the numbers of extrusions. SEM studies showed that substantially different morphology with better adhesion existed when SCA‐treated blends were compared to nontreated PP–PET blends. The presence of individual melting temperatures of the polymers in all compositions with no significant Tm depression indicated that PET and PP were crystallized separately. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1039–1048, 2003
- 6 May 2003
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 89 (4) , 1039-1048
Melt blending of poly(ethylene terephthalate) with polypropylene in the presence of silane coupling agent
A silane coupling agent (SCA) was used as a compatibilizer for polypropylene–poly(ethylene teraphthalate) (PP–PET) blends with 20, 40, 50, and 60% PET compositions by weight. PP–PET mixtures were blended with and without an SCA by a single‐screw extruder. The effect of silane modification on the tensile and impact properties of the blends was investigated. The morphology and thermal behavior of the blends were examined with scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), respectively. The presence of the SCA used in this work extensively improved the mechanical properties of the blends. Mechanical properties were found to be highly dependent on the numbers of extrusions. SEM studies showed that substantially different morphology with better adhesion existed when SCA‐treated blends were compared to nontreated PP–PET blends. The presence of individual melting temperatures of the polymers in all compositions with no significant Tm depression indicated that PET and PP were crystallized separately. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1039–1048, 2003
- 10 January 2003
- Published by Taylor & Francis in Journal of Macromolecular Science, Part A
- Vol. 40 (10) , 1081-1093
Preparation of a Conducting Flexible Material from Silane Coupling Agent and Hydroxyl Terminated Polybutadiene Rubber by Hydrolysis and Condensation
Synthesis and characterization of a flexible polymer produced from silane coupling agent (SCA) and hydroxyl terminated polybutadiene (HTPB) were performed. Mechanical properties of chemically and electrochemically prepared conducting composites synthesized from this polymer were investigated. Conductivities of the composites were also measured. Polypyrrole enhanced the mechanical properties of the chemically prepared conducting composite. Doping with iodine greatly changed the conductivity of the composite. However, the change in mechanical properties and the conductivities of the electrochemically prepared composite were not as significant when compared with the electrochemically prepared polypyrrole. Among the composites, a chemically prepared composite was highly flexible like rubber. However, the electrochemically produced composite possesses two orders of magnitude higher conductivity. Also, this composite revealed higher tensile strength and elasticity with respect to pristine polypyrrole.
- 10 January 2003
- Published by Taylor & Francis in Journal of Macromolecular Science, Part A
- Vol. 40 (10) , 1081-1093
Preparation of a Conducting Flexible Material from Silane Coupling Agent and Hydroxyl Terminated Polybutadiene Rubber by Hydrolysis and Condensation
Synthesis and characterization of a flexible polymer produced from silane coupling agent (SCA) and hydroxyl terminated polybutadiene (HTPB) were performed. Mechanical properties of chemically and electrochemically prepared conducting composites synthesized from this polymer were investigated. Conductivities of the composites were also measured. Polypyrrole enhanced the mechanical properties of the chemically prepared conducting composite. Doping with iodine greatly changed the conductivity of the composite. However, the change in mechanical properties and the conductivities of the electrochemically prepared composite were not as significant when compared with the electrochemically prepared polypyrrole. Among the composites, a chemically prepared composite was highly flexible like rubber. However, the electrochemically produced composite possesses two orders of magnitude higher conductivity. Also, this composite revealed higher tensile strength and elasticity with respect to pristine polypyrrole.