Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Christos Karapanagiotis has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Traffic-Induced Structural Response Monitoring of Bridges Using Distributed Fiber Optic Sensing

    by Christos Karapanagiotis, Omar Ettaouaje, Mathias Breithaupt, Aleksander Wosniok

    In this paper, we use distributed fiber optic sensing (DFOS) for traffic load monitoring on a newly constructed bridge instrumented with a network of embedded optical fibers. Specifically, the optical fibers are embedded longitudinally in all bridge girders at two depths, forming a looped sensing configuration that enables the measurement of different stress states when a vehicle passes. The measurements presented here were conducted before the bridge was opened to traffic, using a mobile crane weighing approximately 36 metric tons, with the load distributed evenly across three axles. We show that our DFOS system can effectively capture the bridge structural response to the moving mobile crane and provide estimates of axle weight distribution and spacing. Finally, the results indicate that, although the fibers located in the girders beneath the loaded lane are strongly affected by the traffic, the fibers beneath the unloaded lane show only a negligible response, highlighting the ability to separate the effects of vehicles traveling in neighboring lanes.

  • Open Access

    Implementation of Distributed Fiber Optic Sensors for Structural Health Monitoring in New Bridge Structures

    by Aleksander Wosniok, Hentschke Bau GmbH, Stephan Dunkel, Frank Basedau, Mathias Breithaupt, Christos Karapanagiotis

    Structural health monitoring has traditionally been applied primarily to existing structures that already exhibit damage or load-bearing deficits. In such cases, a customized monitoring concept is typically developed to address the specific condition of the structure. This reactive approach, however, contrasts with the objectives of predictive infrastructure management, which aim to detect changes at an early stage and support long-term planning. For new bridge constructions, a shift toward proactive and integrated monitoring is therefore highly desirable. Key requirements for such an approach include the permanent availability of pre-installed sensing technology, reliable power supply and data transmission, measurement procedures without traffic disruptions, on-demand data retrieval, and the implementation of a reference or baseline measurement immediately after construction. This baseline allows any subsequent structural changes throughout the lifecycle of the bridge to be identified with high accuracy. Moreover, comprehensive monitoring supports efficient maintenance planning by combining sensor data with traditional inspection results. New bridge structures offer ideal conditions for embedded monitoring systems, as modern, robust, and cost-effective sensors can be installed permanently and non-invasively in all relevant components, including those that will later become difficult to access. Continuous monitoring provides several key benefits as early detection of damage such as corrosion or cracking, improved planning of maintenance interventions, optimization of inspection intervals, and reduction of costs and traffic restrictions. Furthermore, real structural loads resulting from variable influences such as traffic, temperature, or wind can be recorded and analyzed in detail, supporting fatigue assessments, remaining service life predictions, and the development of digital twins. Additional advantages include the detection of overloads and unauthorized heavy transports, as well as faster structural assessment following exceptional events such as fires or slope failures. This paper presents the instrumentation of a newly constructed prestressed concrete bridge using distributed fiber optic sensing (DFOS). The fiber optic sensors were integrated into all major components of the structure, including the deck slab, abutments, and all precast girders. The fiber optic sensing cables were designed to allow flexible configuration of measurement sections. During the construction phase, verification measurements and a load test were performed to evaluate installation quality, sensor performance, and data reliability. The results demonstrate that DFOS is a powerful and practical technology for structural health monitoring of new bridge constructions and represents a key enabler for predictive maintenance management.

  • Open Access

    Real-time monitoring of hydrogen composite pressure vessels using surface-applied distributed fiber optic sensors

    by Christos Karapanagiotis, Mathias Breithaupt, Eric Duffner, Marcus Schukar

    In this paper, we report to the best of our knowledge for the first time on continuous real-time monitoring of composite overwrapped pressure vessels (COPVs) designed for hydrogen storage using surface-applied distributed fiber optic sensors (DFOS). We conducted continuous and real-time DFOS measurements during pressure cycling tests consisting of periodic pressure fluctuations between 20 bar and 875 bar, with a rate of 5 cycles min−1. During pressure cycling, the DFOS system measured strain changes, that under normal operating conditions were linearly correlated to changes in pressure. To detect and quantify damage-related anomalies, we trained a simple regression model to predict strain from pressure data and used the difference between predicted and measured values as a damage indicator. With our approach, the DFOS system not only detected and localized the damage but also continuously tracked its evolution in real time under dynamic pressure conditions. Furthermore, unlike previous studies where optical fibers were embedded within the composite structure, we applied them on the COPV surface, reducing both implementation cost and time while eliminating the need to modify the COPV manufacturing process. Based on our results, we are confident that DFOS can enhance safety and facilitate the transition from time-consuming periodic inspections to more efficient, machine learning-based predictive maintenance.


  • Open Access

    Towards predictive maintenance of hydrogen pressure vessels based on multi-sensor data

    by BAM Federal Institute for Materials Research and Testing, Christos Karapanagiotis, Jan Heimann, Eric Duffner, Amir Charmi, Marcus Schukar, Seyedreza Hashemi, Jens Prager

    In this paper, we report on a sensor network for structural health monitoring (SHM) of Type IV composite overwrapped pressure vessels (COPVs) designed for hydrogen storage. The sensor network consists of three different SHM sensing technologies: ultrasonic guided waves (GW), acoustic emission (AE) testing, and distributed fiber optic sensors (DFOS). We present an experimental setup for a lifetime test, where a COPV is subjected to cyclic loading. Data from all sensors are collected and centrally evaluated. The COPV failed after approximately 60,000 load cycles, and the sensor network proved capable of detecting and localizing the damage even before the failure of the COPV. This multi-sensor approach offers significantly more channels of information and could therefore enable a transition from costly and time-consuming periodic inspections to more efficient and modern predictive maintenance strategies, including artificial intelligence (AI)-based evaluation. This not only has a positive effect on operational costs but enhances safety through the early identification of critical conditions in the overall system in real-time. In the future, we aim to integrate the measurement setup into a hydrogen refueling station with the data stream implemented into a digital signal processing chain and a digital twin.


  • Open Access

    How structural health monitoring can be embedded in a digital quality infrastructure: an example.

    by BAM Federal Institute for Materials Research and Testing, Jan Heimann, Amir Charmi, Christos Karapanagiotis, Seyedreza Hashemi, Jens Prager

    The digital Quality Infrastructure (QI) initiative “QI-Digital” in Germany is focusing on implementing new technologies and approaches to ensure that the task of quality assurance is more efficient and ready for the digital and green transformation of the economy. The implementation of quality control key elements, such as Smart Standards, Digital Certificates and QI-cloud solutions shall contribute to solving the socio-economic, ecological, and technological challenges of our time. Hydrogen is a key energy carrier and has the potential to play a significant role in the energy transition, especially in mobility. An essential factor for the broad acceptance of hydrogen-based mobility is the availability of refueling stations that operate reliably and safely. Using the example of a Hydrogen Refueling Station (HRS) build within the QI-Digital initative, the Federal Institute for Material Research and Testing (BAM) aims to establish a real laboratory where modern measurement techniques and new digital methods are implemented to enhance operational safety, availability, and economic efficiency and render the technology more attractive for the industry. In this work, we present an approach to establish a Structural Health Monitoring (SHM) system on a high-pressure buffer inside HRS and show how it could be embedded into a digital QI. The high-pressure buffers are essential components of the plant which are currently inspected periodically without regard to their operating history. Focusing on the transition to a continuous and digitally supported monitoring of the component’s integrity during operation the novel inspection scheme will be linked to a completely digitalized component-related documentation and tested using digital certificates. This allows the operational safety and, if necessary, the remaining useful lifetime to be assessed on an ongoing basis and to be a valuable contribution to increase the sustainability.


  • Open Access

    Structural health monitoring of hydrogen pressure vessels using distributed fiber optic sensing

    by BAM Federal Institute for Materials Research and Testing, Christos Karapanagiotis, Marcus Schukar, Mathias Breithaupt, Eric Duffner, Alexander Ulbricht, Jens Prager, Katerina Krebber

    We report on distributed fiber optic sensing-based monitoring of hydrogen composite overwrapped pressure vessels (COPV) to simultaneously increase the operational lifespan and mitigate maintenance costs. Our approach represents, to the best of our knowledge, the first application of distributed fiber optic sensing for COPV Type IV monitoring, where the sensing fibers are attached to the surface, rather than integrated into the composite material. Specifically, we attach an optical fiber of 50 m to the pressure vessel's surface, covering both the cylindrical and dome sections. We note that our fiber optic sensing technique relies on swept wavelength interferometry providing strain information along the entire length of the optical fiber with high spatial resolution even at the millimeter scale. When the vessel is pressurized, the sensing optical fiber shows a linear strain response to pressure at every position along the fiber. After thousands of load cycles, the vessel finally fails with the optical fiber detecting and precisely localizing the damage in the vessel’s blind dome area. Furthermore, we discuss the potential of state-of-the-art signal processing methods and machine learning for advancing predictive maintenance. This could reduce the number of regular inspections, mitigate premature maintenance costs, and simultaneously increase the vessel’s remaining safe service life. We believe that the structural health monitoring of hydrogen pressure vessels with fiber optic sensors can enhance trust in hydrogen technology contributing to the energy transition in the future.


  • Open Access

    Machine Learning Approaches in Brillouin Distributed Fiber Optic Sensors

    by Christos Karapanagiotis, Katerina Krebber

    This paper presents reported machine learning approaches in the field of Brillouin distributed fiber optic sensors (DFOSs). The increasing popularity of Brillouin DFOSs stems from their capability to continuously monitor temperature and strain along kilometer-long optical fibers, rendering them attractive for industrial applications, such as the structural health monitoring of large civil infrastructures and pipelines. In recent years, machine learning has been integrated into the Brillouin DFOS signal processing, resulting in fast and enhanced temperature, strain, and humidity measurements without increasing the system’s cost. Machine learning has also contributed to enhanced spatial resolution in Brillouin optical time domain analysis (BOTDA) systems and shorter measurement times in Brillouin optical frequency domain analysis (BOFDA) systems. This paper provides an overview of the applied machine learning methodologies in Brillouin DFOSs, as well as future perspectives in this area.


  • Open Access

    Distributed fiber optic sensors for structural health monitoring of composite pressure vessels

    by Christos Karapanagiotis, Marcus Schukar, Katerina Krebber

    In this paper, we present a comprehensive overview of our research in the field of distributed fiber optic sensors for structural health monitoring of hydrogen composite pressure vessels. Specifically, we demonstrate how the integration of fiber optic sensors into composite pressure vessels enhances safety while simultaneously reducing maintenance costs. The small size of optical fibers enables their integration into composite structures during the manufacturing process, allowing continuous monitoring and precise detection and localization of structural damages during service life. We also discuss the potential of state-of-the-art signal processing methods and machine learning for advancing predictive maintenance. Our applications of fiber optic sensors demonstrate their potential to contribute significantly to the energy transition towards renewable sources.


  • Machine learning assisted BOFDA for simultaneous temperature and strain sensing in a standard optical fiber

    by Christos Karapanagiotis, Konstantin Hicke, Katerina Krebber

    We report, to our knowledge for the first time on simultaneous distributed temperature and strain sensing in a standard telecom optical fiber using a machine learning assisted Brillouin frequency domain analysis (BOFDA) system. The well-known temperature and strain cross-sensitivity problem is addressed by developing a BOFDA system with a high signal-to-noise ratio and applying machine learning. The spectrum consists of four highly resolved peaks, whose Brillouin frequency shifts are extracted and serve as features for the machine learning algorithms. The spectra result from a 450-m standard SMF-28 optical fiber, and particularly from a segment of 30 m. This fiber segment is coiled around a stretcher and placed in a climate chamber. The applied temperature and strain values range from 20 °C to 40 °C and from 0 µɛ to 1380 µɛ, respectively. The total measurement time to achieve a high SNR and resolve four peaks with a spatial resolution of 6 m is 16 min. To discriminate temperature and strain effects, simple frequentist and more sophisticated Bayesian-based algorithms are employed with the powerful Gaussian process regression (GPR) delivering the best performance in terms of temperature and strain errors, which are found to be 2 °C and 45 µɛ, respectively. These errors are calculated using leave-one-out cross-validation, so that an unbiased estimation of the sensor’s performance is provided.


  • Machine learning for strain, temperature and humidity discrimination in Brillouin optical frequency domain analysis

    by Christos Karapanagiotis, Katerina Krebber

    We propose to our knowledge for the first time an ensemble of probabilistic machine learning models for strain, temperature and humidity discrimination in Brillouin optical frequency domain analysis (BOFDA) applying a two-fiber configuration.