Anjana Dissanayake
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Anjana Dissanayake has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Benton H. Calhoun
Department of Electrical and Computer Engineering, University of Virginia, Charlottesville, VA, USA
6 shared publications - Henry L. Bishop
Amazon.com, Inc., Redmond, WA, USA
5 shared publications - Steven Michael Bowers
Department of Electrical and Computer Engineering, University of Virginia, Charlottesville, USA
4 shared publications Sang-Gug Lee
Department of Electrical Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701, Korea
3 shared publications- Daniel S. Truesdell
University of Virginia
2 shared publications - Divya Duvvuri
Silicon Labs, Austin, TX, USA
2 shared publications
Latest Publications
- Open Access
- 10 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Solid-State Circuits Society
- Vol. 4, 43-56
A–102-dBm Sensitivity Multichannel Heterodyne Wake-Up Receiver With Integrated ADPLL
This paper presents a binary frequency-shift keying (BFSK) heterodyne wake-up receiver (WuRx) with -102 dBm sensitivity at 2.4 GHz. An integrated low-power all-digital phase-locked loop (ADPLL) allows sharp filtering at the intermediate frequency (IF) to improve sensitivity and interference robustness. The WuRx achieves an average current consumption of 2.2 μA to 171 μA range at 16 s to 0.1 s latency with the packet-level-duty-cycling scheme. In addition, it supports up to 60 channels from 2.300 GHz to 2.536 GHz. A signal-to-interference ratio (SIR) of -27/-30/-46 dB is achieved at 3/5/25 MHz offset from the carrier.
- 10 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Solid-State Circuits Society
- Vol. 4, 43-56
Open AccessA–102-dBm Sensitivity Multichannel Heterodyne Wake-Up Receiver With Integrated ADPLL
This paper presents a binary frequency-shift keying (BFSK) heterodyne wake-up receiver (WuRx) with -102 dBm sensitivity at 2.4 GHz. An integrated low-power all-digital phase-locked loop (ADPLL) allows sharp filtering at the intermediate frequency (IF) to improve sensitivity and interference robustness. The WuRx achieves an average current consumption of 2.2 μA to 171 μA range at 16 s to 0.1 s latency with the packet-level-duty-cycling scheme. In addition, it supports up to 60 channels from 2.300 GHz to 2.536 GHz. A signal-to-interference ratio (SIR) of -27/-30/-46 dB is achieved at 3/5/25 MHz offset from the carrier.
- 23 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (1) , 744-757
A 184-nW, −78.3-dBm Sensitivity Antenna-Coupled Supply, Temperature, and Interference-Robust Wake-Up Receiver at 4.9 GHz
This article presents a highly integrated, supply, temperature, and interference-robust, event-driven wake-up receiver (WuRx) achieving$< -78.3$ -dBm sensitivity using a custom-designed antenna at 4.9 GHz or$< -72.3$ -dBm sensitivity when matched to a 50-$\Omega $ source at 5.3 GHz, consuming 184 nW at room temperature. The chip is fabricated in 65-nm CMOS LP technology and powered by a single supply. A novel slot antenna is proposed to directly conjugate match to the input of the chip and eliminate lossy impedance matching networks. The integrated references and regulation enable the receiver to operate for a wide range of temperatures from$-30\,\,^\circ \text{C}$ to 70$^\circ \text{C}$ and a supply range from 1.2 to 1.5 V. The integrated proportional–integral–derivative (PID) control module allows the WuRx to automatically adapt for different temperatures and interference signals present in the ambient environment.- 23 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 70 (1) , 744-757
A 184-nW, −78.3-dBm Sensitivity Antenna-Coupled Supply, Temperature, and Interference-Robust Wake-Up Receiver at 4.9 GHz
This article presents a highly integrated, supply, temperature, and interference-robust, event-driven wake-up receiver (WuRx) achieving$< -78.3$ -dBm sensitivity using a custom-designed antenna at 4.9 GHz or$< -72.3$ -dBm sensitivity when matched to a 50-$\Omega $ source at 5.3 GHz, consuming 184 nW at room temperature. The chip is fabricated in 65-nm CMOS LP technology and powered by a single supply. A novel slot antenna is proposed to directly conjugate match to the input of the chip and eliminate lossy impedance matching networks. The integrated references and regulation enable the receiver to operate for a wide range of temperatures from$-30\,\,^\circ \text{C}$ to 70$^\circ \text{C}$ and a supply range from 1.2 to 1.5 V. The integrated proportional–integral–derivative (PID) control module allows the WuRx to automatically adapt for different temperatures and interference signals present in the ambient environment.- 23 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (3) , 917-931
A 2.4 GHz-91.5 dBm Sensitivity Within-Packet Duty-Cycled Wake-Up Receiver
This article presents a highly integrated 2.4-GHz wake-up receiver (WuRX) achieving 91.5 dBm sensitivity with a state-of-the-art power and latency combination of 2$\mu \text{W}$ at 100 ms. The proposed within-packet duty-cycling method employs a carrier-sense mechanism to turn off the WuRX early under idle channel conditions, which reduces the dc-power compared with conventional asynchronous packet-level duty cycling by$9\times $ at 10 ms latency (21$\mu \text{W}$ ) and$2\times $ at 1 s latency (0.9$\mu \text{W}$ ) at the cost of 2 dB in sensitivity. The uncertain-IF topology with a phase-locked loop (PLL)-aided event-driven calibrated local-oscillator (LO) helps reduce the dc-power while maintaining a fast startup. The channel-embedded OOK scheme is used to create a deterministic IF to enable baseband (BB) channel selection and achieve continuous wave (CW) interference tolerance of −47 dB at 20 MHz offset. Fabricated in 65 nm CMOS, input matching and$LC$ oscillator are all implemented on-chip, and operation is demonstrated with integrated low dropout regulators to capture the degradations in realistic system integration.- 23 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (3) , 917-931
A 2.4 GHz-91.5 dBm Sensitivity Within-Packet Duty-Cycled Wake-Up Receiver
This article presents a highly integrated 2.4-GHz wake-up receiver (WuRX) achieving 91.5 dBm sensitivity with a state-of-the-art power and latency combination of 2$\mu \text{W}$ at 100 ms. The proposed within-packet duty-cycling method employs a carrier-sense mechanism to turn off the WuRX early under idle channel conditions, which reduces the dc-power compared with conventional asynchronous packet-level duty cycling by$9\times $ at 10 ms latency (21$\mu \text{W}$ ) and$2\times $ at 1 s latency (0.9$\mu \text{W}$ ) at the cost of 2 dB in sensitivity. The uncertain-IF topology with a phase-locked loop (PLL)-aided event-driven calibrated local-oscillator (LO) helps reduce the dc-power while maintaining a fast startup. The channel-embedded OOK scheme is used to create a deterministic IF to enable baseband (BB) channel selection and achieve continuous wave (CW) interference tolerance of −47 dB at 20 MHz offset. Fabricated in 65 nm CMOS, input matching and$LC$ oscillator are all implemented on-chip, and operation is demonstrated with integrated low dropout regulators to capture the degradations in realistic system integration.- 12 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (4) , 1058-1070
A 0.6V 785-nW Multimodal Sensor Interface IC for Ozone Pollutant Sensing and Correlated Cardiovascular Disease Monitoring
In this article, we present the design and analysis of a 785-nW multimodal sensor interface IC for ozone pollutant sensing and correlated cardiovascular disease monitoring based on electrocardiography (ECG) and photoplethysmography (PPG). The proposed hybrid dc offset current cancellation (DCOC) along with a 4- MΩ gain-regulated cascode transimpedance amplifier (RGC-TIA) enable PPG readout power reduction by 37×, compared with the state-of-the-art PPG sensor interfaces. The ozone sensing channel proposes an adaptive architecture to enable low V DD operation, achieving a 300× power reduction, compared with the state-of-the-art gas sensing readouts. The ozone sensing channel's performance was also verified using custom resistive metal-oxide sensors for concentrations from 50 to 900 ppb. The sensor interface IC is fabricated in a 65-nm CMOS, integrating a 165-nW voltage-mode ECG channel, a 532-nW current-mode PPG channel, 76-nW resistive-mode ozone channel, and 12.6-nW peripheral circuits, all at 0.6 V. The total system power consumption including the LED and a custom digital readout IC is 10.98- 15.51 μW, which is 41×- 57× less than prior ozone/CVD joint monitoring sensor interface systems.
- 12 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (4) , 1058-1070
A 0.6V 785-nW Multimodal Sensor Interface IC for Ozone Pollutant Sensing and Correlated Cardiovascular Disease Monitoring
In this article, we present the design and analysis of a 785-nW multimodal sensor interface IC for ozone pollutant sensing and correlated cardiovascular disease monitoring based on electrocardiography (ECG) and photoplethysmography (PPG). The proposed hybrid dc offset current cancellation (DCOC) along with a 4- MΩ gain-regulated cascode transimpedance amplifier (RGC-TIA) enable PPG readout power reduction by 37×, compared with the state-of-the-art PPG sensor interfaces. The ozone sensing channel proposes an adaptive architecture to enable low V DD operation, achieving a 300× power reduction, compared with the state-of-the-art gas sensing readouts. The ozone sensing channel's performance was also verified using custom resistive metal-oxide sensors for concentrations from 50 to 900 ppb. The sensor interface IC is fabricated in a 65-nm CMOS, integrating a 165-nW voltage-mode ECG channel, a 532-nW current-mode PPG channel, 76-nW resistive-mode ozone channel, and 12.6-nW peripheral circuits, all at 0.6 V. The total system power consumption including the LED and a custom digital readout IC is 10.98- 15.51 μW, which is 41×- 57× less than prior ozone/CVD joint monitoring sensor interface systems.
- 1 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A- 108dBm Sensitivity, -28dB SIR, 130nW to 41µW, Digitally Reconfigurable Bit-Level Duty-Cycled Wakeup and Data Receiver
A -108dBm sensitivity, 430MHz, 130nW-41µW, 6.25bps-4.2kbps, digitally tunable wake-up and data receiver in 65nm CMOS is presented. Employing 2-tone RF OOK modulation and an AlN MEMS resonator, the receiver attains close-in SIR of -25dB at 0.12% and far-out SIR of -28dB at 0.7% frequency offset from the carrier. Digitally configurable dynamic ranges of 11dB, 410X, 672X are achieved for sensitivity, power, and latency, respectively. The design receives data at a 4.2kbps bit-rate at - 108dBm sensitivity while consuming 41µW. The proposed WuRx is a highly reconfigurable and interference robust candidate for emerging ultra-long range IoT LPWAN applications.
- 1 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A- 108dBm Sensitivity, -28dB SIR, 130nW to 41µW, Digitally Reconfigurable Bit-Level Duty-Cycled Wakeup and Data Receiver
A -108dBm sensitivity, 430MHz, 130nW-41µW, 6.25bps-4.2kbps, digitally tunable wake-up and data receiver in 65nm CMOS is presented. Employing 2-tone RF OOK modulation and an AlN MEMS resonator, the receiver attains close-in SIR of -25dB at 0.12% and far-out SIR of -28dB at 0.7% frequency offset from the carrier. Digitally configurable dynamic ranges of 11dB, 410X, 672X are achieved for sensitivity, power, and latency, respectively. The design receives data at a 4.2kbps bit-rate at - 108dBm sensitivity while consuming 41µW. The proposed WuRx is a highly reconfigurable and interference robust candidate for emerging ultra-long range IoT LPWAN applications.
- Open Access
- 3 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (7) , 1952-1959
A 2.5 ppm/°C 1.05-MHz Relaxation Oscillator With Dynamic Frequency-Error Compensation and Fast Start-Up Time
This paper presents a 1.05 MHz, on-chip RC relaxation oscillator (ROSC) with a temperature coefficient (TC) of 2.5 ppm/°C and an absolute variation of 100 ppm over the body-compatible range of 0-40°C. The TC increases to 4.3 ppm/°C over the range from -15 °C to 55 °C. The high temperature stability is achieved using a PTAT current reference and a TC-tunable resistor bank for first-order frequency error compensation along with a digital frequency compensation (DFC) block using a single-bit temperature sensor for second-order compensation. A measured RMS period jitter of 160 ps is achieved with a high-speed comparator. The active power consumption of the ROSC is 69 μW with a 1-V supply, and the leakage power consumption is 110 nW, while power gated. The ROSC achieves a fast startup time of 8 μs by employing a voltage buffer to quickly stabilize the voltage reference.
- 3 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (7) , 1952-1959
Open AccessA 2.5 ppm/°C 1.05-MHz Relaxation Oscillator With Dynamic Frequency-Error Compensation and Fast Start-Up Time
This paper presents a 1.05 MHz, on-chip RC relaxation oscillator (ROSC) with a temperature coefficient (TC) of 2.5 ppm/°C and an absolute variation of 100 ppm over the body-compatible range of 0-40°C. The TC increases to 4.3 ppm/°C over the range from -15 °C to 55 °C. The high temperature stability is achieved using a PTAT current reference and a TC-tunable resistor bank for first-order frequency error compensation along with a digital frequency compensation (DFC) block using a single-bit temperature sensor for second-order compensation. A measured RMS period jitter of 160 ps is achieved with a high-speed comparator. The active power consumption of the ROSC is 69 μW with a 1-V supply, and the leakage power consumption is 110 nW, while power gated. The ROSC achieves a fast startup time of 8 μs by employing a voltage buffer to quickly stabilize the voltage reference.
- 26 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 65 (11) , 1579-1583
A 45- $\mu$ W, 162.1-dBc/Hz FoM, 490-MHz Two-Stage Differential Ring VCO Without a Cross-Coupled LatchAn ultra-low-power, start-up and phase noise performance improved 2-stage differential ring voltage-controlled oscillator (VCO) is proposed. The proposed delay cell architecture reduces power consumption by eliminating the cross-coupling latch of the conventional ring VCO. Instead of the latch, the inverters in the proposed delay cell produce negative conductance by insertion of an additional RC network, which improves the start-up performance of the proposed VCO. The proposed delay cell architecture also improves the phase noise performance of the VCO as it sharpens the drain current of the inverter stage such that it resembles an impulse waveform, which reduces the root-mean-square (rms) value of impulse sensitivity function (ISF). Implemented in a 65nm CMOS technology, the measured phase noise of the proposed VCO at 1MHz offset is -94.84dBc/Hz at 490MHz oscillation frequency while dissipating 45lW from a 0.6V supply. The figure of merit (FoM) is 162.1dBc/Hz.
- 26 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 65 (11) , 1579-1583
A 45- $\mu$ W, 162.1-dBc/Hz FoM, 490-MHz Two-Stage Differential Ring VCO Without a Cross-Coupled LatchAn ultra-low-power, start-up and phase noise performance improved 2-stage differential ring voltage-controlled oscillator (VCO) is proposed. The proposed delay cell architecture reduces power consumption by eliminating the cross-coupling latch of the conventional ring VCO. Instead of the latch, the inverters in the proposed delay cell produce negative conductance by insertion of an additional RC network, which improves the start-up performance of the proposed VCO. The proposed delay cell architecture also improves the phase noise performance of the VCO as it sharpens the drain current of the inverter stage such that it resembles an impulse waveform, which reduces the root-mean-square (rms) value of impulse sensitivity function (ISF). Implemented in a 65nm CMOS technology, the measured phase noise of the proposed VCO at 1MHz offset is -94.84dBc/Hz at 490MHz oscillation frequency while dissipating 45lW from a 0.6V supply. The figure of merit (FoM) is 162.1dBc/Hz.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 184-187
A 64 µW, 23 dB gain, 8 dB NF, 2.4 GHz RF front-end for ultra-low power Internet-of-Things transceivers
An ultra-low power (ULP) 2.4 GHz RF front-end which consists of a low noise amplifier (LNA) and a passive mixer in a standard 65nm CMOS is presented. LNA adopts a complementary input stage and a current reused 2 nd gain stage to achieve a high gain under a low power dissipation with an added linearization method. RF Down-conversion is implemented with a highly linearized complementary passive mixer, which adopts transmission gate type switches. With fully on-chip components, the front-end achieves 23 dB conversion gain, 8 dB NF, -36 dBm P1dB and -21 dBm IIP3 while dissipating a 64 μW power from a 0.6 V supply voltage. LNA achieves a high voltage gain of 26.3 dB and minimum NF of 5.5 dB with a P1dB of -27 dBm and IIP3 of -13 dBm.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 184-187
A 64 µW, 23 dB gain, 8 dB NF, 2.4 GHz RF front-end for ultra-low power Internet-of-Things transceivers
An ultra-low power (ULP) 2.4 GHz RF front-end which consists of a low noise amplifier (LNA) and a passive mixer in a standard 65nm CMOS is presented. LNA adopts a complementary input stage and a current reused 2 nd gain stage to achieve a high gain under a low power dissipation with an added linearization method. RF Down-conversion is implemented with a highly linearized complementary passive mixer, which adopts transmission gate type switches. With fully on-chip components, the front-end achieves 23 dB conversion gain, 8 dB NF, -36 dBm P1dB and -21 dBm IIP3 while dissipating a 64 μW power from a 0.6 V supply voltage. LNA achieves a high voltage gain of 26.3 dB and minimum NF of 5.5 dB with a P1dB of -27 dBm and IIP3 of -13 dBm.