Miloš Pjević
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Miloš Pjević has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Ljubodrag Tanović
Університет Белграда, факультет машинобудування, кафедра виробничої техніки
5 shared publications- Mihajlo Popovic
Faculty of Mechanical Engineering, University of Belgrade, Belgrade, Serbia
5 shared publications - Goran Mladenović
University of Belgrade
2 shared publications Natalija Lazarevic
2 shared publicationsAleksandar Lazic
1 shared publicationAleksandar Lazić
1 shared publication
Latest Publications
- Open Access
Experimental Investigation into Tensile Mechanical Properties of the Unidirectional Flax Fibre–Reinforced Vitrimer Composite—Seeking Sustainable Opportunities for the Automotive Industry
Emerging sustainability demands and calls for lowering materials’ environmental impact have directed authors to examine a class of polymers characterised as covalent adaptable networks and referred to as vitrimers. In this study, composite plates were made using vitrimer resin as the matrix material and continuous unidirectional flax fibre fabrics as the reinforcement. A specific early-stage composite part production method is proposed to make the multi-ply flax/vitrimer composite plate. The development of natural fibre–reinforced vitrimer composites is of clear research interest as a promising approach towards sustainable and recyclable novel material systems. Specimens prepared with all the plies oriented 0° exhibited a 129.4 MPa tensile strength and a 12.4 GPa tensile modulus, indicating a 334% increase in tensile strength when compared to the average value of 29.8 MPa obtained for neat vitrimer specimens and a 1140% improvement in the tensile modulus compared to the 1.0 GPa reached for neat vitrimer. The specimens whose plies were oriented 90° are found to deliver a tensile strength of 12.2 MPa and a 1.3 GPa tensile modulus. Applying the classical composite material micromechanics equation to calculate the 0°-direction tensile modulus demonstrated a good agreement with the experimentally obtained value—a 9.6% difference was discovered. Proper fibre/matrix interfacial adhesion was detected when the flax/vitrimer specimens’ surfaces after fracture were examined under scanning electron microscope. The research findings on tensile mechanical properties reveal that the observed flax/vitrimer composites may be potential candidates for replacing typical synthetic fibre–reinforced materials rated for automotive applications and intended for in-plane loaded parts, particularly some inner-body vehicle elements.
Open AccessExperimental Investigation into Tensile Mechanical Properties of the Unidirectional Flax Fibre–Reinforced Vitrimer Composite—Seeking Sustainable Opportunities for the Automotive Industry
Emerging sustainability demands and calls for lowering materials’ environmental impact have directed authors to examine a class of polymers characterised as covalent adaptable networks and referred to as vitrimers. In this study, composite plates were made using vitrimer resin as the matrix material and continuous unidirectional flax fibre fabrics as the reinforcement. A specific early-stage composite part production method is proposed to make the multi-ply flax/vitrimer composite plate. The development of natural fibre–reinforced vitrimer composites is of clear research interest as a promising approach towards sustainable and recyclable novel material systems. Specimens prepared with all the plies oriented 0° exhibited a 129.4 MPa tensile strength and a 12.4 GPa tensile modulus, indicating a 334% increase in tensile strength when compared to the average value of 29.8 MPa obtained for neat vitrimer specimens and a 1140% improvement in the tensile modulus compared to the 1.0 GPa reached for neat vitrimer. The specimens whose plies were oriented 90° are found to deliver a tensile strength of 12.2 MPa and a 1.3 GPa tensile modulus. Applying the classical composite material micromechanics equation to calculate the 0°-direction tensile modulus demonstrated a good agreement with the experimentally obtained value—a 9.6% difference was discovered. Proper fibre/matrix interfacial adhesion was detected when the flax/vitrimer specimens’ surfaces after fracture were examined under scanning electron microscope. The research findings on tensile mechanical properties reveal that the observed flax/vitrimer composites may be potential candidates for replacing typical synthetic fibre–reinforced materials rated for automotive applications and intended for in-plane loaded parts, particularly some inner-body vehicle elements.
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Additive Technologies in the Service of Advanced Robotics and Vice Versa
For decades, since the introduction of the first industrial robot, Unimate, achieving a harmonious balance between performance and feasible robotic design has been essential. Manufacturing limitations, material availability, and sensor and actuator systems have significantly influenced robotic system design. However, since their commercial debut in 1986, additive manufacturing (AM) technologies have been revolutionizing how once-unimaginable ideas are designed, presented, and ultimately produced. This paper explores the achievements in additive manufacturing with a special focus on its application in advanced robotics. A detailed classification of existing additive technologies is presented, along with a comprehensive review of their advantages in specific robotic applications. The growing role of additive technologies in expanding robotics across industries is also discussed. Furthermore, the increasing presence of advanced robotics in households, alongside AM, is largely driven by the exponential advancement of artificial intelligence (AI). AI contributes not only to the development of control models but also to the structural design of robotic systems. As a result, robotics itself plays a crucial role in the ongoing evolution of additive technologies, a key focus of this paper. One critical aspect explored is the development of models for active vibration damping, addressing vibrations as an undesirable phenomenon in production processes. Additionally, the integration of additive technologies with robotics enhances sustainability by reducing material waste, improving energy efficiency, and enabling the use of eco-friendly materials. These innovations are already reshaping industries such as aerospace, medical robotics, and construction, where additive manufacturing enables the creation of lightweight, customized, and highly functional robotic components. Future advancements in hybrid manufacturing, multi-material printing, and AI-driven process optimization will further enhance the synergy between additive technologies and robotics, paving the way for more autonomous, efficient, and adaptable robotic systems.
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Additive Technologies in the Service of Advanced Robotics and Vice Versa
For decades, since the introduction of the first industrial robot, Unimate, achieving a harmonious balance between performance and feasible robotic design has been essential. Manufacturing limitations, material availability, and sensor and actuator systems have significantly influenced robotic system design. However, since their commercial debut in 1986, additive manufacturing (AM) technologies have been revolutionizing how once-unimaginable ideas are designed, presented, and ultimately produced. This paper explores the achievements in additive manufacturing with a special focus on its application in advanced robotics. A detailed classification of existing additive technologies is presented, along with a comprehensive review of their advantages in specific robotic applications. The growing role of additive technologies in expanding robotics across industries is also discussed. Furthermore, the increasing presence of advanced robotics in households, alongside AM, is largely driven by the exponential advancement of artificial intelligence (AI). AI contributes not only to the development of control models but also to the structural design of robotic systems. As a result, robotics itself plays a crucial role in the ongoing evolution of additive technologies, a key focus of this paper. One critical aspect explored is the development of models for active vibration damping, addressing vibrations as an undesirable phenomenon in production processes. Additionally, the integration of additive technologies with robotics enhances sustainability by reducing material waste, improving energy efficiency, and enabling the use of eco-friendly materials. These innovations are already reshaping industries such as aerospace, medical robotics, and construction, where additive manufacturing enables the creation of lightweight, customized, and highly functional robotic components. Future advancements in hybrid manufacturing, multi-material printing, and AI-driven process optimization will further enhance the synergy between additive technologies and robotics, paving the way for more autonomous, efficient, and adaptable robotic systems.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 346-354
OPTIMIZATION OF THE DELTA 3D PRINTER STRUCTURE
In recent years, additive manufacturing technologies have made significant progress in terms of structural solutions, printing parameters, materials, and software support. This paper presents the process of reconstructing and optimizing a damaged and non-functional Delta 3D printer, with the goal of making it suitable for use in an educational setting. A Delta 3D printer is a type of additive manufacturing system distinguished by its unique kinematic structure, where three vertical arms are arranged in a triangular base configuration and simultaneously control the printhead's position. This design enables high-speed operation, precise movement, and fabrication of models with significant height. This configuration is particularly advantageous in educational environments, as it illustrates the diversity of 3D printer mechanisms and underlying engineering principles. Using reverse engineering methods and modern additive manufacturing technologies – FFF (Fused Filament Fabrication) and SLA (Stereolithography), damaged and worn-out components were replaced and certain technical improvements were implemented. The reconstruction involved replacing key components and improving the printer’s functionality and ease of use, making it more suitable for educational purposes. After the reconstruction, the device was successfully tested and is now capable of reliably producing functional models. The printer is operated using Marlin firmware and the Arduino.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 346-354
OPTIMIZATION OF THE DELTA 3D PRINTER STRUCTURE
In recent years, additive manufacturing technologies have made significant progress in terms of structural solutions, printing parameters, materials, and software support. This paper presents the process of reconstructing and optimizing a damaged and non-functional Delta 3D printer, with the goal of making it suitable for use in an educational setting. A Delta 3D printer is a type of additive manufacturing system distinguished by its unique kinematic structure, where three vertical arms are arranged in a triangular base configuration and simultaneously control the printhead's position. This design enables high-speed operation, precise movement, and fabrication of models with significant height. This configuration is particularly advantageous in educational environments, as it illustrates the diversity of 3D printer mechanisms and underlying engineering principles. Using reverse engineering methods and modern additive manufacturing technologies – FFF (Fused Filament Fabrication) and SLA (Stereolithography), damaged and worn-out components were replaced and certain technical improvements were implemented. The reconstruction involved replacing key components and improving the printer’s functionality and ease of use, making it more suitable for educational purposes. After the reconstruction, the device was successfully tested and is now capable of reliably producing functional models. The printer is operated using Marlin firmware and the Arduino.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 355-362
IMPLEMENTATION AND OPTIMIZATION OF THE DELTA 3D PRINTER CONTROL SYSTEM
This paper deals with the implementation of a control system for a Delta 3D printer, which was carried out to enable its use in educational applications. A detailed diagnostic was performed on essential hardware components of the Delta 3D printer, including the Arduino MEGA, RAMPS 1.4 board, stepper motors and their drivers, micro switches, display module, and other electronics. A customized version of the Marlin firmware, adapted for a Delta configuration, was then installed on the Arduino MEGA microcontroller. Key parameters such as build plate dimensions, print height, Delta radius, motor microstepping, and maximum motor speed and acceleration were configured. To optimize stepper motor performance, reference voltages were adjusted, and TL smoothers were installed to ensure stable and quieter operation. The final system evaluation included measuring motor voltage levels, verifying filament flow rates, checking the dimensional accuracy of printed parts, and validating the parameter setup. After hardware and firmware calibration, various slicing software tools available online were tested and compared. The aim of the analysis was to identify the most suitable slicing software for the optimized Delta system, as well as the optimal configuration of its parameters, in order to achieve the highest possible print quality.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 355-362
IMPLEMENTATION AND OPTIMIZATION OF THE DELTA 3D PRINTER CONTROL SYSTEM
This paper deals with the implementation of a control system for a Delta 3D printer, which was carried out to enable its use in educational applications. A detailed diagnostic was performed on essential hardware components of the Delta 3D printer, including the Arduino MEGA, RAMPS 1.4 board, stepper motors and their drivers, micro switches, display module, and other electronics. A customized version of the Marlin firmware, adapted for a Delta configuration, was then installed on the Arduino MEGA microcontroller. Key parameters such as build plate dimensions, print height, Delta radius, motor microstepping, and maximum motor speed and acceleration were configured. To optimize stepper motor performance, reference voltages were adjusted, and TL smoothers were installed to ensure stable and quieter operation. The final system evaluation included measuring motor voltage levels, verifying filament flow rates, checking the dimensional accuracy of printed parts, and validating the parameter setup. After hardware and firmware calibration, various slicing software tools available online were tested and compared. The aim of the analysis was to identify the most suitable slicing software for the optimized Delta system, as well as the optimal configuration of its parameters, in order to achieve the highest possible print quality.
- Open Access
- 21 September 2021
- Published by Igor Sikorsky Kyiv Polytechnic Institute in International Scientific and Technical conference "The Progressive Technics, Technology and Engineering Education"
- No. XXII
Higher Education in The Republic of Serbia from the perspective of the European Educational Area
Process of accession of Higher Education Institutions (HEIs) in Serbia to the Bologna Process was requiring realistic solution while concurrently was nurturing both the existing national education system and appreciation of oversea. After fifteen years of EHEA, still there have been significant differences between national and European education. Implementation of European experiences and harmonization of national with the European Education requires dealing with many issues both at the state level and at the level of Universities and Faculties. In the paper it is presented an analysis of the situation of HEIs in Serbia in comparison with the EHEA in terms of the number of students, the number of HEIs, teaching staff, allocations (costs) per student and the impact of the Covid19 pandemic
- 21 September 2021
- Published by Igor Sikorsky Kyiv Polytechnic Institute in International Scientific and Technical conference "The Progressive Technics, Technology and Engineering Education"
- No. XXII
Open AccessHigher Education in The Republic of Serbia from the perspective of the European Educational Area
Process of accession of Higher Education Institutions (HEIs) in Serbia to the Bologna Process was requiring realistic solution while concurrently was nurturing both the existing national education system and appreciation of oversea. After fifteen years of EHEA, still there have been significant differences between national and European education. Implementation of European experiences and harmonization of national with the European Education requires dealing with many issues both at the state level and at the level of Universities and Faculties. In the paper it is presented an analysis of the situation of HEIs in Serbia in comparison with the EHEA in terms of the number of students, the number of HEIs, teaching staff, allocations (costs) per student and the impact of the Covid19 pandemic
- 1 March 2021
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 9 (1) , 015030
Experimental investigation of the tool radius and micro-cutting speed influence on micro-cutting mechanisms for marble based material
In this paper, a detailed experimental analysis of the effect of tool tip radius and cutting speed on the proposed mechanism of micro-cutting Plavi tok marble was performed. Although Plavi tok marble belongs to extremely brittle materials, experiments have shown that it can be processed in ductile mode (plastic deformation mode), i.e. without the presence of brittle fracturing of the material. Moreover, it has been established that the range of plastic deformation zone is a function of the tool tip radius and the cutting speed. The diamond tools used during the experiments had tip radius values of r = 0.15 and r = 0.2 mm, while cutting speeds were 15 and 25 m s −1 . When using tools with higher tip radius values, with increasing cutting speed, the critical penetration depth (ductile-brittle transition) increased from 8.8 to 9.3 μ m. On the other hand, tools with lower radius value led to a reduction of the plastic deformation zone range. This declining trend of plastic deformation zone continued during increased cutting speed, with critical penetration depths of 8.6 and 8.3 μ m for cutting speeds of 15 and 25 m s −1 , respectively. The intensity of lateral/radial destruction in the brittle fracturing mode was also directly dependent on the processing conditions. The reduction was achieved by using tools with a lower value of the tip radius while processing at lower speeds. In this paper, the identification of the components of the cutting force was carried out, whose intensities indicate the occurrence of the brittle destruction within the material.
- 1 March 2021
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 9 (1) , 015030
Experimental investigation of the tool radius and micro-cutting speed influence on micro-cutting mechanisms for marble based material
In this paper, a detailed experimental analysis of the effect of tool tip radius and cutting speed on the proposed mechanism of micro-cutting Plavi tok marble was performed. Although Plavi tok marble belongs to extremely brittle materials, experiments have shown that it can be processed in ductile mode (plastic deformation mode), i.e. without the presence of brittle fracturing of the material. Moreover, it has been established that the range of plastic deformation zone is a function of the tool tip radius and the cutting speed. The diamond tools used during the experiments had tip radius values of r = 0.15 and r = 0.2 mm, while cutting speeds were 15 and 25 m s −1 . When using tools with higher tip radius values, with increasing cutting speed, the critical penetration depth (ductile-brittle transition) increased from 8.8 to 9.3 μ m. On the other hand, tools with lower radius value led to a reduction of the plastic deformation zone range. This declining trend of plastic deformation zone continued during increased cutting speed, with critical penetration depths of 8.6 and 8.3 μ m for cutting speeds of 15 and 25 m s −1 , respectively. The intensity of lateral/radial destruction in the brittle fracturing mode was also directly dependent on the processing conditions. The reduction was achieved by using tools with a lower value of the tip radius while processing at lower speeds. In this paper, the identification of the components of the cutting force was carried out, whose intensities indicate the occurrence of the brittle destruction within the material.
- 15 December 2020
- Published by Faculty of Technical Sciences in Advanced Technologies & Materials
- Vol. 45 (2) , 17-20
Recycling system for the FDM/FFF method material designed for small and medium-sized production batches
With fast growing industry in the field of additive technology, possibilities of DIY (Do It Yourself) projects grow as well. This also gives the opportunity for non-expert's users to project and develop some complex products on their own. The reaction was global overflow of the 3D printer's sale worldwide. If we look in the long term, environmental pollution caused by their disposed polymer is their biggest flaw. Recycling process sometimes can be very expensive, and in certain cases unavailable for some users. In this paper, low-cost recycling system for materials that are most commonly used for FDM/FFF method is presented. The main goal was to reduce environmental pollution and 3D printing costs by presenting the possibility of making its own polymer made of scrape plastic. Moreover, this allows users to make their own recipe by mixing different types of scrape polymer, or adding reinforcing material such as chopped dry fibre, metal powder, etc.
- 15 December 2020
- Published by Faculty of Technical Sciences in Advanced Technologies & Materials
- Vol. 45 (2) , 17-20
Recycling system for the FDM/FFF method material designed for small and medium-sized production batches
With fast growing industry in the field of additive technology, possibilities of DIY (Do It Yourself) projects grow as well. This also gives the opportunity for non-expert's users to project and develop some complex products on their own. The reaction was global overflow of the 3D printer's sale worldwide. If we look in the long term, environmental pollution caused by their disposed polymer is their biggest flaw. Recycling process sometimes can be very expensive, and in certain cases unavailable for some users. In this paper, low-cost recycling system for materials that are most commonly used for FDM/FFF method is presented. The main goal was to reduce environmental pollution and 3D printing costs by presenting the possibility of making its own polymer made of scrape plastic. Moreover, this allows users to make their own recipe by mixing different types of scrape polymer, or adding reinforcing material such as chopped dry fibre, metal powder, etc.
- Open Access
- 1 January 2018
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 46 (1) , 80-85
Contemporary approach to the design of circular form tools for complex-geometry part manufacture
Form tools have been used in industry for a number of decades. Their use is booming and such growing popularity can be attributed to minimized manufacturing costs and shorter manufacturing time. On the other side, one of the major drawbacks is the method of their design. It reflects in the constraints present in the machining of straight-line and circular arc segments of a workpiece. For each segment the rake angle has a different value, which imposes an additional constraint. In case it is necessary to use form tools to manufacture complex-geometry parts, the value of the rake angle would require to be zero. The paper presents contemporary design method of circular form tools by implementing CAD system. This way, it is not only provided a constant value of the rake angle across the entire cutting edge, which can be different from zero too, but also optimum tool geometry for machining a desired material. Additionally, the geometry of a form tool designed using a new method was experimentally tested.
- 1 January 2018
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 46 (1) , 80-85
Open AccessContemporary approach to the design of circular form tools for complex-geometry part manufacture
Form tools have been used in industry for a number of decades. Their use is booming and such growing popularity can be attributed to minimized manufacturing costs and shorter manufacturing time. On the other side, one of the major drawbacks is the method of their design. It reflects in the constraints present in the machining of straight-line and circular arc segments of a workpiece. For each segment the rake angle has a different value, which imposes an additional constraint. In case it is necessary to use form tools to manufacture complex-geometry parts, the value of the rake angle would require to be zero. The paper presents contemporary design method of circular form tools by implementing CAD system. This way, it is not only provided a constant value of the rake angle across the entire cutting edge, which can be different from zero too, but also optimum tool geometry for machining a desired material. Additionally, the geometry of a form tool designed using a new method was experimentally tested.
- 16 May 2017
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 139 (4)
Experimental Examination of the Impact of Tool Radius on Specific Energy in Microcutting of Granite
The paper presents experimental results of microcutting brittle materials (granite). The analysis was conceived on the observed interaction between the workpiece and two tools of different shapes. Experiment was based on scratching the workpiece surface with diamond tools. Applied tools had tip radius R0.2 and R0.15 mm. The experiment determined the changes in the value of perpendicular and tangential components of the cutting force based on the geometric properties of tools, as well as the changes of the specific energy of microcutting granite (Jošanica and Bukovik types). The experiment has shown that reduction of tool radius causes reduction of the cutting force intensity and specific cutting energy. Because of its physical/mechanical properties, more energy is required for micromachining granite “Jošanica” than “Bukovik.” Based on the topography of the surface, the value of critical tool penetration depth was established, after which the brittle fracture is no longer present. For granite “Jošanica” values of critical penetration depth are 6 and 5 μm when micromachining with tools R0.2 and R0.15 mm, while for Bukovik those values are 6.5 and 5.5 μm. The paper should form the basis for understanding the phenomena which occur during microcutting brittle materials.
- 16 May 2017
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 139 (4)
Experimental Examination of the Impact of Tool Radius on Specific Energy in Microcutting of Granite
The paper presents experimental results of microcutting brittle materials (granite). The analysis was conceived on the observed interaction between the workpiece and two tools of different shapes. Experiment was based on scratching the workpiece surface with diamond tools. Applied tools had tip radius R0.2 and R0.15 mm. The experiment determined the changes in the value of perpendicular and tangential components of the cutting force based on the geometric properties of tools, as well as the changes of the specific energy of microcutting granite (Jošanica and Bukovik types). The experiment has shown that reduction of tool radius causes reduction of the cutting force intensity and specific cutting energy. Because of its physical/mechanical properties, more energy is required for micromachining granite “Jošanica” than “Bukovik.” Based on the topography of the surface, the value of critical tool penetration depth was established, after which the brittle fracture is no longer present. For granite “Jošanica” values of critical penetration depth are 6 and 5 μm when micromachining with tools R0.2 and R0.15 mm, while for Bukovik those values are 6.5 and 5.5 μm. The paper should form the basis for understanding the phenomena which occur during microcutting brittle materials.