Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Chang Liu has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Early bird gets the network: The relative importance of reactivity ratios, Ψ parameter, and crosslinker level on gel formation in FRP

    by Yung‐Chun Lin, Chang Liu, Amit K. Tripathi, John G. Tsavalas

    Network topology is manipulated in free‐radical copolymerization via proper selection of crosslinker type and its respective properties when paired with specific monomers. Our prior work has focused on the impact of the reduced reactivity parameter Ψ applied to a pendent vinyl, characteristic for each monomer/crosslinker pair, yet here we assess the relative importance of the comonomer reactivity ratios to see whether one factor can counterbalance the other. The traditional reactivity ratio determines when the crosslinker molecule is incorporated into the polymer backbone, while the reduced reactivity Ψ parameter relates to the efficiency of the resulting pendent side chain vinyl being utilized to form a crosslink node at some later point during the polymerization. Both factors are then contrasted with simply the overall loading of crosslinker. Either n‐butyl methacrylate (n‐BMA) or styrene (STY) was chosen as a primary backbone monomer to copolymerize with one of three crosslinkers: 1,4‐butanediol dimethacylate (BDDMA), 1,4‐butanediol diacrylate (BDDA), or divinylbenzene (DVB). Both kinetics and gel can be most dramatically boosted when a crosslinker is applied having a reactivity ratio favouring early insertion. This in turn leads to an earlier onset of gel formation, which ultimately results in greater final gel content. This amplification of both kinetics and gel can overcome an otherwise small Ψ due to crosslinker or main monomer choice. This reactivity ratio effect was further confirmed by Monte Carlo simulations. By whatever mechanism (higher Ψ, lower rA, or higher crosslinker level), earlier onset of gelation produces more gel overall and a tighter network topology.


  • Open Access

    Crosslinking in Semi-Batch Seeded Emulsion Polymerization: Effect of Linear and Non-Linear Monomer Feeding Rate Profiles on Gel Formation

    by Chang Liu, Amit K. Tripathi, Wei Gao, John G. Tsavalas

    Waterborne latex is often called a product-of-process. Here, the effect of semi-batch monomer feed rate on the kinetics and gel formation in seeded emulsion polymerization was investigated for the copolymerization of n-butyl methacrylate (n-BMA) and ethylene glycol dimethacrylate (EGDMA). Strikingly, the gel fraction was observed to be significantly influenced by monomer feed rate, even while most of the experiments were performed under so-called starve-fed conditions. More flooded conditions from faster monomer feed rates, including seeded batch reactions, counterintuitively resulted in significantly higher gel fraction. Chain transfer to polymer was intentionally suppressed here via monomer selection so as to focus mechanistic insights to relate only to the influence of a divinyl monomer, as opposed to being clouded by contributions to topology from long chain branching. Simulations revealed that the dominant influence on this phenomenon was the sensitivity of primary intramolecular cyclization to the instantaneous unreacted monomer concentration, which is directly impacted by monomer feed rate. The rate constant for cyclization for these conditions was determined to be first order and 4000 s−1, approximately 4 times that typically observed for backbiting in acrylates. This concept has been explored previously for bulk and solution polymerizations, but not for emulsified reaction environments and especially for the very low mole fraction divinyl monomer. In addition, while gel fraction could be dramatically manipulated by variations in linear monomer feed rates, it could be markedly enhanced by leveraging non-linear feed profiles built from combination sequences of flooded and starved conditions. For a 2 h total feed time, a fully linear profile resulted in 30% gel while a corresponding non-linear profile with an early fast-feed segment resulted in 80% gel.